staging/blocktrron/package/boot, branch master

mediatek filogic: differentiate RUTC50 model

2025-11-12T18:43:27Z

Differentiate the RUTC50 model by variant. Teltonika ships the RUTC50 based on customer order as NAND or eMMC variant without NAND. The eMMC variant supports additional eSIM support, not present in the NAND variant. Variants can be differentiated by order-code as explained in the RUTC50 datasheet. Order-Code "RUTC50 *0****" - NAND Order-Code "RUTC50 *1****" - eMMC + eSIM Signed-off-by: David Bauer

qualcommax: ipq50xx: Add support for CMCC PZ-L8

2025-11-12T13:34:07Z

CMCC PZ-L8 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on IPQ5000. Specifications: - SoC : Qualcomm IPQ5000 - RAM : Integrated 256MiB DDR3L - Flash : 128 MiB SPI-NAND (ESMT F50D1G41LB) - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : Qualcomm IPQ5000 (SoC) - 5 GHz : Qualcomm Atheros QCN6102 - Ethernet : 4x 10/100/1000 Mbps - switch : Qualcomm Atheros QCA8337 - LEDs/Keys (GPIO) : 2x LEDs, 2x Keys - UART : Through-hole on PCB, 4pins in the middle of the black aluminum heat sink - assignment : 3.3V, GND,TX, RX (from left to right) - settings : 115200n8 - Power : 12 VDC, 1 A Flashing Instructions: 1. SSH Method (1) Enable SSH on the stock firmware a. Version 501.8 and 501.9: Log in to http://192.168.10.1 with the password on the sticker Append "/admin/system/admin" to the URL and press Enter Delete "Dropbear instance", click "Add instance", then "Save and Apply" Reboot the router b. Version 501.11 and 501.12: While the router is running the stock firmware, press and hold the reset button for 20-30 seconds Open http://192.168.10.1:56781 and login with username "root" and the password on the sticker Run "vi /etc/config/dropbear" and delete the line "option enable '0'" Reboot the router (2) Upload the factory.ubi file to router's /tmp directory (using scp or wget) and execute the following commands in the router's shell export rootfs=$(cat /proc/mtd | grep rootfs | grep -v _ | cut -d: -f1) ubidetach -f -p /dev/${rootfs} ubiformat /dev/${rootfs} -y -f /tmp/factory.ubi 2. U-Boot Method using UBI Image Place the factory.ubi file on your TFTP server, enter U-Boot CLI and exec these commands tftpboot :factory.ubi flash rootfs reset 3. U-Boot Method using initramfs Image (1) Place the openwrt-*-initramfs-fit-uImage.itb file on your TFTP server and rename it to initramfs.bin (2) Enable serial console, enter to U-Boot CLI and exec these commands tftpboot :initramfs.bin bootm (3) Once boot completed, upload the sysupgrade.bin file to router's /tmp directory (using scp or wget) and execute the following command in openwrt shell sysupgrade -n /tmp/sysupgrade.bin Switching to the Stock Firmware: Please follow the commit https://github.com/openwrt/openwrt/commit/3b7d72bc2ecca2f962319b0a4fb9beb7609a0222 Partition Layout (Stock Firmware): 0x000000000000-0x000000080000 : "0:SBL1" 0x000000080000-0x000000100000 : "0:MIBIB" 0x000000100000-0x000000140000 : "0:BOOTCONFIG" 0x000000140000-0x000000180000 : "0:BOOTCONFIG1" 0x000000180000-0x000000280000 : "0:QSEE" 0x000000280000-0x000000380000 : "0:QSEE_1" 0x000000380000-0x0000003c0000 : "0:DEVCFG" 0x0000003c0000-0x000000400000 : "0:DEVCFG_1" 0x000000400000-0x000000440000 : "0:CDT" 0x000000440000-0x000000480000 : "0:CDT_1" 0x000000480000-0x000000500000 : "0:APPSBLENV" 0x000000500000-0x000000640000 : "0:APPSBL" 0x000000640000-0x000000780000 : "0:APPSBL_1" 0x000000780000-0x000000880000 : "0:ART" 0x000000880000-0x000000900000 : "0:TRAINING" 0x000000900000-0x000004300000 : "rootfs" 0x000004300000-0x000007d00000 : "rootfs_1" Notes: This device is almost the same as ELECOM WRC-X3000GS2, including partition layout and the dual-boot feature. Known Issues: - All Wi-Fi related peripherals are disabled in device tree, since 256 MiB RAM is too few for ath11k. - This device has another version with nand flash FM25SL01, which is not supported at the moment. https://github.com/immortalwrt/immortalwrt/blob/master/target/linux/mediatek/patches-6.12/342-mtd-spinand-Support-fmsh.patch MAC Addresses: Interface MAC Address Location (binary) LAN A4:39:B6:xx:xx:9D (0:ART, 0x00-0x05) WAN A4:39:B6:xx:xx:9E (0:ART, 0x06-0x0B) 2.4 GHz A4:39:B6:xx:xx:9F (0:ART, 0x0C-0x11) 5 GHz A4:39:B6:xx:xx:A0 (0:ART, 0x12-0x17) Signed-off-by: Chang Liu

uboot-airoha: drop HIDDEN option

2025-11-10T18:16:01Z

Drop HIDDEN option from U-Boot default for Airoha while support for ATF gets pushed. Signed-off-by: Christian Marangi

uboot-rockchip: add support for LinkEase EasePi R1

2025-11-09T22:13:25Z

generic-rk3568 is enough Signed-off-by: Liangbin Lian Link: https://github.com/openwrt/openwrt/pull/20147 Signed-off-by: Hauke Mehrtens

uboot-d1: fix build with swig 4.3.0

2025-11-09T22:00:44Z

Swig 4.3.0 has changed SWIG_Python_AppendOutput, which now requires an additional parameter `is_void`. SWIG_AppendOutput remains unchanged. This was fixed upstream in u-boot/u-boot@a63456b ``` scripts/dtc/pylibfdt/libfdt_wrap.c: In function ‘_wrap_fdt_next_node’: scripts/dtc/pylibfdt/libfdt_wrap.c:5581:17: error: too few arguments to function ‘SWIG_Python_AppendOutput’ 5581 | resultobj = SWIG_Python_AppendOutput(resultobj, val); | ^~~~~~~~~~~~~~~~~~~~~~~~ ``` This is the same fix as applied in 363e07d. Fixes: #20619 Link: #20620 Signed-off-by: Trix Taiclet Link: https://github.com/openwrt/openwrt/pull/20620 Signed-off-by: Hauke Mehrtens

mediatek: add support for COMFAST CF-WR632AX

2025-11-09T18:33:18Z

COMFAST CF-WR632AX is a compact/travel (123.4 mm * 88.7 mm * 34 mm) wireless WiFi 6 router. Specification ------------- - SoC : MediaTek MT7981B dual-core ARM Cortex-A53 1.3 GHz - RAM : DDR3 512 MiB - Flash : SPI-NAND 128 MiB (Winbond) - WLAN : MediaTek MT7976CN dual-band WiFi 6 - 2.4 GHz : b/g/n/ax, MU-MIMO (2x 5 dBi antennas) - 5 GHz : a/n/ac/ax, MU-MIMO (2x 5 dBi antennas) - Ethernet : - LAN x1 : 10/100/1000 Mbps (MT7981 internal PHY) - WAN x1 : 10/100/1000/2500 Mbps (Maxlinear GPY211C) - USB x1 : 3.0 - UART : through-hole on PCB - assignment : (RX), (TX), (GND), [VCC] - settings : 115200n8 - Buttons x1 : Reset - LEDs x3 : Status (Blue, Green, Red) - Fan x1 : PWM, 4-wire, 5 V, 0.3 A, 45 mm * 10 mm - Power : 5 VDC, 3 A, Type-C Flash instructions ------------------ WebUI Method: 1. Install the *squashfs-sysupgrade.bin image using the stock WebUI update page. 2. Press and hold the reset button after reboot to wipe the stock config. SSH Method: 1. Import stock firmware settings from backup file github.com/andros-ua/owrt-misc/blob/main/cf-wr632ax/backup.file Note: WebUI password will be reset to admin1234 after import. 2. Connect via SSH using root:openwrt credentials. 3. Upload the *squashfs-sysupgrade.bin image. 4. Use the command: sysupgrade -n All checks should pass. Return to stock --------------- Flash a stock firmware using the OpenWrt sysupgrade method. Recovery -------- Power on the router while holding the Reset button until the LED flashes 5 times. The U-Boot Flash WebUI will be available at http://192.168.1.1 or Connect UART and use the U-Boot menu to flash the firmware image or boot an OpenWrt initramfs image. OpenWrt U-Boot flash instructions --------------------------------- 1. Flash ordinary OpenWrt image. 2. Login into the device and backup everything, especially 'Factory' part. 3. Unlock mtd partitions: apk add kmod-mtd-rw insmod mtd-rw i_want_a_brick=1 4. Write new BL2 and FIP: mtd write openwrt-mediatek-filogic-comfast_cf-wr632ax-ubootmod-preloader.bin BL2 mtd write openwrt-mediatek-filogic-comfast_cf-wr632ax-ubootmod-bl31-uboot.fip FIP 5. Set static IP on your PC: ip 192.168.1.254 mask 255.255.255.0 6. Serve OpenWrt initramfs image using TFTP server. 7. Reboot device, wait for TFTP recovery to complete. 8. After OpenWrt has booted, perform sysupgrade. MAC Addresses: ---------------------------------------------------------- | Interface | MAC | Source | ---------------|-------------------|---------------------- | WAN (label) | 40:A5:EF:xx:xx:xx | Factory, 0xe000 | | LAN | 40:A5:EF:xx:xx:xx | Factory, 0xe000 + 1 | | WLAN 2.4 GHz | 40:A5:EF:xx:xx:xx | Factory, 0x4 | | WLAN 5 GHz | 40:A5:EF:xx:xx:xx | Factory, 0x8000 | ---------------------------------------------------------- Signed-off-by: Andrii Kuiukoff Link: https://github.com/openwrt/openwrt/pull/20382 Signed-off-by: Hauke Mehrtens

mediatek: filogic: add support for TP-LINK BE450

2025-11-08T22:39:59Z

This commit adds support for TP-LINK BE450. Device specification -------------------- SoC Type: MediaTek MT7988D, Cortex-A73, 64-bit RAM: 512MB Flash: SPI NAND GigaDevice (128 MiB) Ethernet: MediaTek MT7531AE (3 Ports) + 2.5GbE (internal MT7988 phy) + 10GbE (RTL8261N) WLAN: MT7992 WLAN 2g: MediaTek MT7975N, b/g/n/ax/be, MIMO 4x4 WLAN 5g: MediaTek MT7979N, a/n/ac/ax/be, MIMO 4x4 LEDs: 8 LEDs, 1 status blue, 2x WIFI blue, 2x Internet blue/orange, 1 LAN blue, 1 usb blue, 1 wps blue, gpio-controlled Button: 2 (Reset, WPS) USB port: Yes Power: 12 VDC, 2 A Connector: Barrel Bootloader: Main U-Boot - U-Boot 2023.10-rc4. Additionally, ubi0 partition contain "seconduboot" (also U-Boot 2023.10-rc4) Serial console (UART), unpopulated, located near the power connector --------------------- heatsink | | | | | | +----+-----+------+-------+ +-----------------+ | | | TX | RX | GND | +3.3V | | power connector | +---+ +----+-----+------+-------+ +-----------------+ | Don't connect ----+ Disassemble: rm the 2 screws at the bottom and the one at the backside. un-clip the case starting at the edge above the LEDs. Installation (UART) ------------------- 1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2 2. Attach UART, switch on the router and interrupt the boot process by pressing 'Ctrl-C' 3. Load and run OpenWrt initramfs image: tftpboot 0x50000000 openwrt-mediatek-filogic-tplink_be450-initramfs-kernel.bin && bootm 0x50000000 4. Run 'sysupgrade -n' with the sysupgrade OpenWrt image Note: the 10GbE (RTL8261N) is only working if reverting this Realtek target specific commit: https://github.com/openwrt/openwrt/commit/b77fa45d1278443d534919598c0301719fed2784 The second ubi partition (ubi1) is empty and there is no known dual-partition mechanism, neither in u-boot nor in the stock firmware. NMBM is not used. Not Working: WED, if activated, MT7992 isn't recognized any more. Signed-off-by: Dirk Buchwalder Link: https://github.com/openwrt/openwrt/pull/20398 Signed-off-by: Hauke Mehrtens

uboot-envtools: handle U-Boot environment on the BPi-R4 Lite

2025-11-05T14:19:40Z

The BPi-R4 Lite uses the same defaults like all other BananaPi boards to store the bootloader environment on the boot media. Signed-off-by: Daniel Golle

uboot-mediatek: add support for the BananaPi BPi-R4 Lite

2025-11-05T14:19:40Z

The BPi R4 Lite can boot from microSD, SPI-NAND, SPI-NOR and eMMC. Build menu-driven U-Boot for each storage option. Provide options for installation from microSD to SPI-NAND and SPI-NOR, and from SPI-NAND to eMMC (similar to BPi-R3). Signed-off-by: Daniel Golle

uboot-mediatek: add builds for the MediaTek MT7987 reference board

2025-11-05T14:19:39Z

Build the (upstream) configuration for the MT7987 reference board, and enable support for DT-overlay application which will be necessary to use the image for the MT7987 RFB generated in OpenWrt. Adapt our downstream patches (generic reset button, rootdisk selection) for MT7987 to prepare for real-world boards. Signed-off-by: Daniel Golle