staging/chunkeey/package/boot, branch master

ipq40xx: add support for Linksys WHW01 v1

2022-05-19T14:39:11Z

This patch adds support for Linksys WHW01 v1 ("Velop") [FCC ID Q87-03331]. Specification ------------- SOC: Qualcomm IPQ4018 WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n WiFi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac Bluetooth: Qualcomm CSR8811 (A12U) Ethernet: Qualcomm QCA8072 (2-port) SPI Flash 1: Mactronix MX25L1605D (2MB) SPI Flash 2: Winbond W25M02GV (256MB) DRAM: Nanya NT5CC128M16IP-DI (256MB) LED Controller: NXP PCA963x (I2C) Buttons: Single reset button (GPIO). Notes ----- There does not appear to be a way to trigger TFTP recovery without entering U-Boot. The device must be opened to access the serial console in order to first flash OpenWrt onto a device from factory. The device has automatic recovery backed by a second set of partitions on the larger of the two SPI flash ICs. Both the primary and secondary must be flashed to prevent accidental rollback to "factory" after 3 failed boot attempts. Serial console -------------- A serial console is available on the following pins of the populated J2 connector on the device mainboard (115200 8n1). (<-- Top of PCB / Device) J2 [o o o o o o] | | | | | `-- GND | `---- TX `--------- RX Installation instructions ------------------------- 1. Setup TFTP server with server IP set to 192.168.1.236. 2. Copy compiled `...squashfs-factory.bin` to `nodes-jr.img` in tftp root. 3. Connect to console using pinout detailed in the serial console section. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash first partition device via `run flashimg`. 6. Once complete, reset device and allow to power up completely. 7. Once comfortable with device upgrade reboot and drop back into U-Boot. 8. Flash the second partition (recovery) via `run flashimg2`. Revert to "factory" ------------------- 1. Download latest firmware update from vendor support site. 2. Copy extracted `.img` file to `nodes-jr.img` in tftp root. 3. Connect to console using pinout detailed in the serial console section. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash first partition device via `run flashimg`. 6. Once complete, reset device and allow to power up completely. 7. Once comfortable with device upgrade reboot and drop back into U-Boot. 8. Flash the second partition (recovery) via `run flashimg2`. Signed-off-by: Peter Adkins (calibration from nvmem, updated to 5.10+5.15) Signed-off-by: Christian Lamparter

uboot-fritz4040: Add support for Toshiba NAND

2022-05-14T09:08:45Z

From Andreas Böhler: "Some revisions of the FRITZ!7530 use a Toshiba NAND with 8 bit ECC in contrast to the Macronix NAND with 4 bit ECC.". Uboot needs to know this in order to have a chance to load from the NAND. Signed-off-by: Christian Lamparter

realtek: add support for ZyXEL GS1900-16

2022-05-07T15:23:45Z

The ZyXEL GS1900-16 is a 16 port gigabit switch similar to other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-16 * SoC: Realtek RTL8382M 500 MHz MIPS 4KEc * Flash: 16 MiB Macronix MX25L12835F * RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8HE * Ethernet: 16x 10/100/1000 Mbps * LEDs: 1 PWR LED (green, not configurable) 1 SYS LED (green, configurable) 16 ethernet port link/activity LEDs (green, SoC controlled) * Buttons: 1 "RESET" button on front panel * Power 120-240V AC C13 * UART: 1 serial header (J12) with populated standard pin connector on the right back of the PCB. Pinout (front to back): + Pin 1 - VCC marked with white dot + Pin 2 - RX + Pin 3 - TX + PIn 4 - GND Serial connection parameters: 115200 8N1. Installation ------------ OEM upgrade method: * Log in to OEM management web interface * Navigate to Maintenance > Firmware * Select the HTTP radio button * Select the Active radio button * Use the browse button to locate the realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin file amd select open so File Path is update with filename. * Select the Apply button. Screen will display "Prepare for firmware upgrade ...". *Wait until screen shows "Do you really want to reboot?" then select the OK button * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. U-Boot TFTP method: * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on * Since the GS1900-16 is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only boot from the first partition anyway (hardcoded in the DTS). To make sure we are manipulating the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. Signed-off-by: Raylynn Knight [removed duplicate patch title, align RAM specification] Signed-off-by: Sander Vanheule

ipq806x: add support for Arris TR4400 v2 / RAC2V1A

2022-05-05T00:19:00Z

Hardware specs: SoC: Qualcomm IPQ8065 (dual core Cortex-A15) RAM: 512 MB DDR3 Flash: 256 MB NAND, 32 MB NOR WiFi: QCA9983 2.4 GHz, QCA9984 5 GHz Switch: QCA8337 Ethernet: 5x 10/100/1000 Mbit/s USB: 1x USB 3.0 Type-A Buttons: WPS, Reset Power: 12 VDC, 2.5 A Ethernet ports: 1x WAN: connected to eth2 4x LAN: connected via the switch to eth0 and eth1 (eth0 is disabled in OEM firmware) MAC addresses (OEM and OpenWrt): fw_env @ 0x00 d4:ab:82:??:??:?a LAN (eth1) fw_env @ 0x06 d4:ab:82:??:??:?b WAN (eth2) fw_env @ 0x0c d4:ab:82:??:??:?c WLAN 2.4 GHz (ath1) fw_env @ 0x12 d4:ab:82:??:??:?d WLAN 5 GHz (ath0) fw_env @ 0x18 d4:ab:82:??:??:?e OEM usage unknown (eth0 in OpenWrt) OID d4:ab:82 is registered to: ARRIS Group, Inc., 6450 Sequence Drive, San Diego CA 92121, US More info: https://openwrt.org/inbox/toh/arris/tr4400_v2 IMPORTANT: This port requires moving the 'fw_env' partition prior to first boot to consolidate 70% of the usable space in flash into a contiguous partition. 'fw_env' contains factory-programmed MAC addresses, SSIDs, and passwords. Its contents must be copied to 'rootfs_1' prior to booting via initramfs. Note that the stock 'fw_env' partition will be wiped during sysupgrade. A writable 'stock_fw_env' partition pointing to the old, stock location is included in the port to help rolling back this change if desired. Installation: - Requires serial access and a TFTP server. - Fully boot stock, press ENTER, type in: mtd erase /dev/mtd21 dd if=/dev/mtd22 bs=128K count=1 | mtd write - /dev/mtd21 umount /config && ubidetach -m 23 && mtd erase /dev/mtd23 - Reboot and interrupt U-Boot by pressing a key, type in: set mtdids 'nand0=nand0' set mtdparts 'mtdparts=nand0:155M@0x6500000(mtd_ubi)' set bootcmd 'ubi part mtd_ubi && ubi read 0x44000000 kernel && bootm' env save - Setup TFTP server serving initramfs image as 'recovery.bin', type in: set ipaddr 192.168.1.1 set serverip 192.168.1.2 tftpboot recovery.bin && bootm - Use sysupgrade to install squashfs image. This port is based on work done by AmadeusGhost . Signed-off-by: Rodrigo Balerdi [add 5.15 changes for 0069-arm-boot-add-dts-files.patch] Signed-off-by: Sungbo Eo

uboot-mvebu: update to version v2022.04

2022-04-30T22:42:30Z

Release announcement: https://lore.kernel.org/u-boot/20220404143253.GQ14476@bill-the-cat/ Release notes between tags: https://source.denx.de/u-boot/u-boot/-/compare/v2022.01...v2022.04?from_project_id=531 All patches were removed, since they are included in this release. Run tested: Turris Omnia, mvebu/cortex-a9, OpenWrt daily snapshots Signed-off-by: Josef Schlehofer

uboot-mvebu: remove enabled CONFIG_CMD_SETEXPR

2022-04-30T22:42:30Z

We don't need to make sure that we want to have enabled CONFIG_CMD_SETEXPR by default, since this is already done in U-boot [1]. This was actually needed only for clearfog board [2], which was added in commit: da0005a6d08ae33d958a6d8a6c0c12dc07b5b2b8 ("uboot-mvebu: add patch to enable setexpr for clearfog boards) and send to U-boot to fix it properly. After a while, there was added support for Turris Omnia, which uses setexpr as well [3], but for this board, there are no fixes needed in U-boot and that's why we can remove this option here. It is helpful with shell scripting. If some downstream distributions are using it, they should correct it in defconfig for related boards. [1] https://source.denx.de/u-boot/u-boot/-/blob/e95afa56753cebcd20a5114b6d121f281b789006/cmd/Kconfig#L1504 [2] https://github.com/openwrt/openwrt/blob/852126680e21edc71c0c66561ae5a6d7479dcc67/target/linux/mvebu/image/clearfog.bootscript#L7 [3] https://github.com/openwrt/openwrt/blob/852126680e21edc71c0c66561ae5a6d7479dcc67/target/linux/mvebu/image/turris-omnia.bootscript#L2 Signed-off-by: Josef Schlehofer

uboot-mvebu: add patch to enable setexpr for clearfog boards

2022-04-30T22:42:30Z

Option CMD_SETEXPR is already default in U-boot [1], since this was disabled since initial version for this board, there is send this patch to U-boot mailing list to enable it. It is required to use in OpenWrt bootscript for these boards [2]. [1] https://source.denx.de/u-boot/u-boot/-/blob/e95afa56753cebcd20a5114b6d121f281b789006/cmd/Kconfig#L1504 [2] https://github.com/openwrt/openwrt/blob/852126680e21edc71c0c66561ae5a6d7479dcc67/target/linux/mvebu/image/clearfog.bootscript#L7 Signed-off-by: Josef Schlehofer

uboot-envtools: add WS-AP3825i config

2022-04-25T22:57:22Z

Add configuration to use uboot-envtools with the Extreme Networks WS-AP3825i. Signed-off-by: David Bauer

ramips: add support for YunCore AX820/HWAP-AX820

2022-04-23T18:46:25Z

There are two versions which are identical apart from the enclosure: YunCore AX820: indoor ceiling mount AP with integrated antennas YunCore HWAP-AX820: outdoor enclosure with external (N) connectors Hardware specs: SoC: MediaTek MT7621DAT Flash: 16 MiB SPI NOR RAM: 128MiB (DDR3, integrated) WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN) LED: Status (green) Button: Reset Power: 802.11af/at PoE; DC 12V,1A Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external Flash instructions: The "OpenWRT support" version of the AX820 comes with a LEDE-based firmware with proprietary MTK drivers and a luci webinterface and ssh accessible under 192.168.1.1 on LAN; user root, no password. The sysupgrade.bin can be flashed using luci or sysupgrade via ssh, you will have to force the upgrade due to a different factory name. Remember: Do *not* preserve factory configuration! MAC addresses as used by OEM firmware: use address source 2g 44:D1:FA:*:0b Factory 0x0004 (label) 5g 46:D1:FA:*:0b LAA of 2g lan 44:D1:FA:*:0c Factory 0xe000 wan 44:D1:FA:*:0d Factory 0xe000 + 1 The wan MAC can also be found in 0xe006 but is not used by OEM dtb. Due to different MAC handling in mt76 the LAA derived from lan is used for 2g to prevent duplicate MACs when creating multiple interfaces. Signed-off-by: Clemens Hopfer

uboot-mediatek: replace patch with accepted commit

2022-04-20T14:22:45Z

Replace pending patch with version accepted upstream. Other than in the first suggested version, the new property is now called 'u-boot,bootconf' instead of 'bootconf'. Signed-off-by: Daniel Golle