staging/florian/target, branch master

bcm53xx: backport MDIO bus clock initialization fix

2017-05-11T14:04:23Z

Signed-off-by: Rafał Miłecki

bcm53xx: backport USB 3.0 PHY patch cleaning all writes

2017-05-11T14:04:23Z

It doesn't change any bevahior just cleanes up the code. Signed-off-by: Rafał Miłecki

ramips: fixup-mac-address: add missing include

2017-05-10T22:52:03Z

Add missing include of ramips.sh in order to import the missing ramips_board_name() procedure. Fixes FS#774. Signed-off-by: Jo-Philipp Wich

ramips: add support for Asus RT-AC51U

2017-05-10T06:45:12Z

Specification: - SoC: MediaTek MT7620A (580 MHz) - RAM: 64 MiB (Winbond W9751G6JB-25) - Flash: 16 MiB (Spansion S25FL128SAIF00) - LAN: x4 100M - WAN: x1 100M - Others: USB 2.0, reset button, wps button and 9 LEDs Issues: - 5 GHz band is not functional (missing driver support) Installation: Asus windows recovery tool: - install the Asus firmware restoration utility - unplug the router, hold the reset button while powering it on - release when the power LED flashes slowly - specify a static IP on your computer: IP address: 192.168.1.75; Subnet mask 255.255.255.0 - Start the Asus firmware restoration utility, specify the sysupgrade image, and press upload TFTP Recovery method: - set computer to a static ip, 192.168.1.75 - connect computer to the LAN 1 port of the router - hold the reset button while powering on the router for a few seconds - send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put lede-ramips-mt7620-rt-ac51u-squashfs-sysupgrade.bin tftp> quit Signed-off-by: Ørjan Malde

ramips: add new device ZyXEL Keenetic as kn

2017-05-10T06:45:12Z

This device exactly same as NBG-419N but with USB port and USB Led. Specification: - SoC: Ralink RT3052 (MIPS24Kc) @384MHz - RAM: 32 MiB - Flash: 8 MiB - WLAN: WiSoC 2T2R/300Mbps (2.4GHz) - LAN: 4x100M - WAN: 1x100M - USB: 1x2.0 Installation via serial console (57600 8N1) from TFTP server - rename the firmware to something shorter, for example "sysupgrade.bin" (max. 32 chars) - copy firmware TFTP server's directory - when you power on device, and see U-Boot log, immediatly push "2" once. - You will see this message: 2: System Load Linux Kernel then write to Flash via TFTP. Warning!! Erase Linux in Flash then burn new one. Are you sure? - Push "y", and enter: device IP, then TFTP server's IP, and then image firmware file name. The firmware will be downloaded within ~30 seconds and flashed to the device (It will take about 2 minutes). Signed-off-by: Alexey Belyaev [squash commits, compact commit message, fix compatible string, remove superfluous pinmuxes] Signed-off-by: Mathias Kresin

ramips: use GPIO_ACTIVE macros in UBNT-ERX.dts

2017-05-06T07:49:00Z

- reorder includes - use GPIO_ACTIVE_LOW macro instead of hardcoded "1" Signed-off-by: Sven Roederer

ramips: strip padding from TP-Link sysupgrade images

2017-05-05T18:02:19Z

This reduce size of sysupgrade firmware. Signed-off-by: Henryk Heisig

ramips: add factory firmware for Tp-Link C20i/C50

2017-05-05T18:01:28Z

TP-Link firmware doesn't accept sysupgrade.bin with metadata. Signed-off-by: Henryk Heisig

brcm63xx: fix invalid Asmax AR 1004g DTS reference

2017-05-05T17:58:49Z

Build profile for Asmax AR 1004g refers to an invalid DTS "rg100a". The correct DTS for this device is "ar1004g". Signed-off-by: Marcin Jurkowski

lantiq: fix avm fritz box mac addresses

2017-05-05T17:58:49Z

It has been shown that the Fritz boxes have the correct mac address set in the wireless calibration data/eeeprom. Use this mac address as base for the ethernet and xdsl interface increment/decrement the address to match the values stored in the tffs. Signed-off-by: Mathias Kresin