staging/hauke/package, branch v21.02.0-rc1

OpenWrt v21.02.0-rc1: adjust config defaults

2021-04-19T19:10:14Z

Signed-off-by: Hauke Mehrtens

realtek: Add ZyXEL GS1900-8

2021-04-18T10:06:18Z

The ZyXEL GS1900-8 is a 8 port switch without any PoE functionality or SFP ports, but otherwise similar to the other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-8 v1.2 * SoC: Realtek RTL8380M 500 MHz MIPS 4KEc * Flash: Macronix MX25L12835F 16 MiB * RAM: Nanya NT5TU128M8GE-AC 128 MiB DDR2 SDRAM * Ethernet: 8x 10/100/1000 Mbit * LEDs: 1 PWR LED (green, not configurable) 1 SYS LED (green, configurable) 8 ethernet port status LEDs (green, SoC controlled) * Buttons: 1 on-off glide switch at the back (not configurable) 1 reset button at the right side, behind the air-vent (not configurable) 1 reset button on front panel (configurable) * Power 12V 1A barrel connector * UART: 1 serial header (JP2) with populated standard pin connector on the left side of the PCB, towards the back. Pins are labelled: + VCC (3.3V) + TX (really RX) + RX (really TX) + GND the labelling is done from the usb2serial connector's point of view, so RX/ TX are mixed up. Serial connection parameters for both devices: 115200 8N1. Installation ------------ Instructions are identical to those for the GS1900-10HP and GS1900-8HP. * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on * Since the GS1900-10HP is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only boot off the first partition anyway (hardcoded in the DTS). To make sure we are manipulating the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade /tmp/openwrt-realtek-generic-zyxel_gs1900-8-squashfs-sysupgrade.bin Signed-off-by: Hauke Mehrtens (cherry picked from commit e6ba970b6ef2289a2a4d3dd6c0c158ee8d10160f)

uboot-envtools: add support for ZyXEL GS-1900-8HP v1 and v2

2021-04-18T10:06:05Z

This adds the necessary nuts and bolts for the uboot settings for both the ZyXEL GS1900-8HP v1 and v2. Signed-off-by: Stijn Segers (cherry picked from commit b5bc53813d28cb4229f9800a36c1e600a239e6a9)

base-files: fix status display command

2021-04-18T10:05:54Z

If service() is called w/o parameter then the status display for services with multiple instances is incorrect. E.g. samba4 or wpad have 2 instances. root@OpenWrt:~# /etc/init.d/samba4 status running root@OpenWrt:~# /etc/init.d/wpad status running Before change: /etc/init.d/samba4 enabled stopped /etc/init.d/wpad enabled stopped After change: /etc/init.d/samba4 enabled running /etc/init.d/wpad enabled running Signed-off-by: Alexander Egorenkov (cherry picked from commit 9318f61556c5443eb66eec7e26715b00f0df86fc)

zram-swap: bail out early if the kernel doesn't support swap

2021-04-18T10:05:53Z

Since KERNEL_SWAP is only enabled by default for !SMALL_FLASH targets, we need to check if the current kernel supports swap before trying to configure zram-swap, as opkg can't check for kernel dependencies. Signed-off-by: Rui Salvaterra (cherry picked from commit 565dfeb1280343fb3f838581169e5d7a1c947862)

uboot-imx6: define 'BUILD_DEVICES' for Toradex Apalis

2021-04-18T10:05:51Z

Without 'BUILD_DEVICES' defined, the U-Boot related package won't be automatically selected when building for Toradex Apalis device. Signed-off-by: Piotr Dymacz (cherry picked from commit 8c3383799a496fda5cfa31000b65c9b8565cf575)

umdns: add missing syscalls to seccomp filter

2021-04-18T10:05:12Z

Looks like 'openat', 'pipe2' and 'ppoll' are now needed, possibly due to changes on libraries used by umdns now using slightly different calls. Found using /etc/init.d/umdns trace now use umdns, ie. cover all ubus call etc., then /etc/init.d/umdns stop find list of syscalls traced in /tmp/umdns.*.json Fixes: FS#3355 ("UMDNS: does not start on master with seccomp") Signed-off-by: Daniel Golle (cherry picked from commit 00a85a163405fdf9bee4d8c3f0ee87ca9ed259d6)

umdns: add syscalls needed on Aarch64

2021-04-18T10:05:08Z

Now that ujail supports seccomp also on Aarch64, add missing syscall 'fstat' to the list of allowed syscalls. Signed-off-by: Daniel Golle (cherry picked from commit d28880cdd86e10142fd86936f5da188eaeeaf9eb)

uboot-envtools: mvebu: add Buffalo LS421DE

2021-04-18T10:04:24Z

The Buffalo Linkstation LS421DE NAS lacks an uboot env config file. Create it via scripts. Signed-off-by: Daniel González Cabanelas (cherry picked from commit 4f8da19572cf1adc480dca42251a4cded0cb3c7c)

kernel: limit crypto-hw-ccp to the x86

2021-04-14T06:42:38Z

CRYPTO_DEV_CCP depends on X86 or ARM64 CRYPTO_DEV_CCP_DD depends on CPU_SUP_AMD or ARM64 Compiling this driver makes sense for x86 mainly. If one day support for ARM64 board with AMD Secure Processor gets added this package may be updated. Trying to build this package on bcm4908 was causing: ERROR: module 'build_dir/target-aarch64_cortex-a53_musl/linux-bcm4908_generic/linux-5.4.110/drivers/crypto/ccp/ccp-crypto.ko' is missing. Signed-off-by: Rafał Miłecki (cherry picked from commit cb3fb45ed1262355e8c31d8e522f411169ee6df8)