staging/hauke/target/linux, branch v21.02.2

ramips: fix NAND flash driver ECC bit position mask

2022-02-16T20:29:10Z

The bit position mask was accidentally made too wide, overlapping with the LSB from the byte position mask. This caused ECC calculation to fail for odd bytes Signed-off-by: Chad Monroe Signed-off-by: Felix Fietkau (cherry-picked from commit 918d4ab41ea34358c747aab5471bbb0a2a786dd8)

kernel: backport fix for initializing skb->cb in the bridge code to 5.4

2022-02-16T19:38:59Z

Fixes issues with proxyarp Signed-off-by: Felix Fietkau (cherry-picked from commit dabc78b644c0fb8f17ff5456f6cb92e78b53f248)

bcm4908: backport watchdog and I2C changes

2022-02-16T08:15:52Z

Signed-off-by: Rafał Miłecki (cherry picked from commit 923cc869a6eec7dd6fdf728b2adb05824e4b9ac0)

bcm4908: backport first 5.18 DTS changes

2022-02-16T08:15:52Z

Signed-off-by: Rafał Miłecki (cherry picked from commit da8b720b0ecbb6d58f28a31b082b0c53be149a5a)

bcm4908: backport bcm_sf2 patch for better LED registers support

2022-02-16T08:15:52Z

Signed-off-by: Rafał Miłecki (cherry picked from commit 840f07e532e081befc2465fd16a0388dd95e55fb)

bcm4908: backport BCM4908 pinctrl driver

2022-02-16T08:15:48Z

Signed-off-by: Rafał Miłecki (cherry picked from commit b0145891676faa38f0a5991e3e229aed7b4a9117)

kernel: bump 5.4 to 5.4.179

2022-02-12T18:41:39Z

Many changes were done in drivers/pinctrl/bcm/pinctrl-bcm2835.c between 5.4.171 and 5.4.179. The following 3 patches do not apply any more: * target/linux/bcm27xx/patches-5.4/950-0316-pinctrl-bcm2835-Add-support-for-BCM2711-pull-up-func.patch This was already integrated in kernel v5.4-rc1, it was never needed. * target/linux/bcm27xx/patches-5.4/950-0328-Revert-pinctrl-bcm2835-Pass-irqchip-when-adding-gpio.patch * target/linux/bcm27xx/patches-5.4/950-0362-pinctrl-bcm2835-Change-init-order-for-gpio-hogs.patch I think these were done to fix the problem which was really fixed in commit 75278f1aff5e ("pinctrl: bcm2835: Change init order for gpio hogs") from v5.4.175 target/linux/generic/backport-5.4/716-v5.5-net-sfp-move-fwnode-parsing-into-sfp-bus-layer.patch Move fwnode_device_is_available to the same position as in kernel 5.10. target/linux/layerscape/patches-5.4/302-dts-0083-arm64-ls1028a-qds-correct-bus-of-rtc.patch Applied in commit 65816c1034769e714edb70f59a33bc5472d9e55f ("arm64: dts: ls1028a-qds: move rtc node to the correct i2c bus") Compile-tested: lantiq/xrx200, bcm27xx/bcm2710 Run-tested: lantiq/xrx200 Signed-off-by: Hauke Mehrtens

ath79: Add support for OpenMesh OM5P-AC v2

2022-02-10T23:28:52Z

Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/200 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * 4x GPIO-LEDs (3x wifi, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + AR8031 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas This device support is based on the partially working stub from commit 53c474abbdfe ("ath79: add new OF only target for QCA MIPS silicon"). Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 .bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp .bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/.bin Signed-off-by: Sven Eckelmann (cherry picked from commit 1699c1dc7f26b332f868d338457abfbe716d6ba0)

lantiq: flag FritzBox 7360 family buttons active-low

2022-01-15T21:49:28Z

All buttons of the FritzBox 7360 family are active-low, not active-high. Corrent the GPIO flag. This fixes release triggers upon push of a button. Reported-by: Jan-Niklas Burfeind Signed-off-by: David Bauer (cherry picked from commit 31545378641d45f5fac5ffc408a31b700b80121f)

kernel: bump 5.4 to 5.4.171

2022-01-13T19:30:59Z

Compile-tested: ath79-generic ipq40xx-generic Run-tested: ath79-generic Signed-off-by: David Bauer