staging/jogo/package/firmware, branch master

ipq40xx: add support for EnGenius EAP2200

2020-02-28T21:29:10Z

SOC: IPQ4019 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB FLASH: NOR 4 MiB + NAND 128 MiB ETH: Qualcomm Atheros QCA8072 WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11a/n/ac 2:2x2 WLAN2: Qualcomm Atheros QCA9888 5GHz 802.11a/n/ac 2:2x2 INPUT: WPS Button LEDS: Power, LAN1, LAN2, WLAN 2.4GHz, WLAN 5GHz-1, WLAN 5GHz-2, OPMODE 1. Load Ramdisk via U-Boot To set up the flash memory environment, do the following: a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters: * 115200bps * 8N1 b. Confirm that the PC is connected to the board using one of the Ethernet ports. c. Set a static ip 192.168.99.8 for Ethernet that connects to board. d. The PC must have a TFTP server launched and listening on the interface to which the board is connected. e. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown. U-BOOT> set serverip 192.168.99.9 && tftpboot 0x84000000 192.168.99.8:openwrt.itb && bootm Signed-off-by: Steven Lin [copied 4.19 dts to 5.4] Signed-off-by: Christian Lamparter

linux-firmware: update to 20200122

2020-02-22T15:38:41Z

Update linux-firmware to 20200122 git log --pretty=oneline --abbrev-commit 20191215..20200122 1eb2408 linux-firmware: Update firmware file for Intel Bluetooth AX200 0dc1611 linux-firmware: Update firmware file for Intel Bluetooth AX201 d03f79c linux-firmware: Update firmware file for Intel Bluetooth 9560 aab62bc linux-firmware: Update firmware file for Intel Bluetooth 9260 ed0aa3a nvidia: add TU102/TU104/TU106 signed firmware 9c340bd amdgpu: update navi10 firmware for 19.50 3b4a503 amdgpu: Add navi10 TA ucode 16cc13a Merge branch 'v1.1.3' of https://github.com/ruiwang-mtk/linux_fw_vpu_v1.1.37f3177d mediatek: update MT8173 VPU firmware to v1.1.3 67d4ff5 Mellanox: Add new mlxsw_spectrum firmware xx.2000.2714 f1c9e7b radeon: update oland rlc microcode from amdgpu b1dafb7 amdgpu: update vega20 microcode for 19.50 c38789e amdgpu: update vega12 microcode for 19.50 5a141c1 amdgpu: update vega10 microcode for 19.50 a03173a amdgpu: update picasso microcode for 19.50 86e9a5f amdgpu: update raven2 microcode for 19.50 febe09a amdgpu: update raven microcode for 19.50 af76fd0 amdgpu: update navi10 microcode for 19.50 b5b176a amdgpu: update navi14 microcode for 19.50 ad90178 amdgpu: add TA microcode for Raven asics 379551b qed: Add firmware 8.42.2.0 58b4003 Merge branch 'RB3-wlan-firmware-1387-v2' of https://github.com/andersson/linux-firmware 5967a45 Adjust WHENCE entry to check_whence doesn't complain d1e743d Merge branch 'master' of https://github.com/NXP/mwifiex-firmware d6219ab qcom: Switch SDM845 WLAN firmware e65245c linux-firmware: add NXP firmware licence file 6871bff Merge branch 'ath10k-20191220' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/linux-firmware b142c2e ath10k: WCN3990 hw1.0: add firmware WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1 8809b87 ath10k: QCA9984 hw1.0: update firmware-5.bin to 10.4-3.9.0.2-00070 513d70c ath10k: QCA988X hw2.0: update firmware-5.bin to 10.2.4-1.0-00047 203435b ath10k: QCA9888 hw2.0: update firmware-5.bin to 10.4-3.9.0.2-00070 a66d2fc ath10k: QCA9887 hw1.0: update firmware-5.bin to 10.2.4-1.0-00047 6d19154 ath10k: QCA6174 hw3.0: update board-2.bin c4586ff linux-firmware: Update AMD cpu microcode Signed-off-by: DENG Qingfang

brcm2708: rename target to bcm27xx

2020-02-14T13:10:51Z

This change makes the names of Broadcom targets consistent by using the common notation based on SoC/CPU ID (which is used internally anyway), bcmXXXX instead of brcmXXXX. This is even used for target TITLE in make menuconfig already, only the short target name used brcm so far. Despite, since subtargets range from bcm2708 to bcm2711, it seems appropriate to use bcm27xx instead of bcm2708 (again, as already done for BOARDNAME). This also renames the packages brcm2708-userland and brcm2708-gpu-fw. Signed-off-by: Adrian Schmutzler Acked-by: Álvaro Fernández Rojas

ath10k-firmware: update ath10k-ct firmware

2020-02-13T16:45:46Z

This supports better per-chain noise floor reporting, which in turn allows for better RSSI reporting in the driver. Wave-2 fixes a long-standing rate-ctrl problem when connected to xbox (and probably other devices). Wave-2 has fix for crash likely related to rekeying. Wave-1 has some debugging code added where a user reported a crash. Tested-by: Stefan Lippers-Hollmann [ipq806x+qca9984,ipq4019+qca9986] Signed-off-by: Michael Yartys

cypress-firmware: update to v4.14.77-2020_0115

2020-02-01T09:59:51Z

Signed-off-by: Álvaro Fernández Rojas

ipq-wifi: drop deprecated .bin support

2020-01-26T00:20:46Z

This patch converts the Qxwlan E2600AC image away from the deprecated .bin file and to the new .qca4019 method. As a result, we no longer need to carry around the legacy support for handling .bin files. Signed-off-by: Christian Lamparter

ipq40xx: add support for EnGenius EMD1

2020-01-26T00:20:45Z

SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8072 (1 port) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button LEDS: White, Blue, Red, Orange Flash instruction: From EnGenius firmware to OpenWrt firmware: In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emd1-squashfs-factory.bin directly. From OpenWrt firmware to EnGenius firmware: 1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8 Put the EnGenius firmware in the TFTP server directory on your computer. 2. Power up EMD1. Press 4 and then press any key to enter u-boot. 3. Download EnGenius firmware (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emd1-nor-fw-s.img 4. Flash the firmware (IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script 5. Reboot (IPQ40xx) # reset Signed-off-by: Yen-Ting-Shen [removed BOARD_NAME] Signed-off-by: Christian Lamparter

ipq40xx: Add support for D-Link DAP-2610

2020-01-26T00:20:45Z

Specifications ============== - SOC: IPQ4018 - RAM: DDR3 256MB - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: IPQ4018, 2x2, front end SKY85303-11 - 5GHz: IPQ4018, 2x2, front end SKY85717-21 - Ethernet: 1x 10/100/1000Mbps, POE 802.3af - PHY: QCA8072 - UART: GND, blocked, 3.3V, RX, TX / 115200 8N1 - LED: 1x red / green - Button: 1x reset / factory default - U-Boot bootloader with tftp and "emergency web server" accessible using serial port. Installation ============ Flash factory image from D-Link web UI. Constraints in the D-Link web UI makes the factory image unnecessarily large. Flash again using sysupgrade from inside OpenWrt to reclaim some flash space. Return to stock D-Link firmware =============================== Partition layout is preserved, and it is possible to return to the stock firmware simply by downloading it from D-Link and writing it to the firmware partition. # mtd -r write dap2610-firmware.bin firmware Quirks ====== To be flashable from the D-Link http server, the firmware must be larger then 6MB, and the size in the firmware header must match the actual file size. Also, the boot loader verifies the checksum of the firmware before each boot, thus the jffs2 must be after the checksum covered part. This is solved in the factory image by having the rootfs at the very end of the image (without pad-rootfs). The sysupgrade image which does not have to be flashable from the D-Link web UI may be smaller, and the checksum in the firmware header only covers the kernel part of the image. Signed-off-by: Fredrik Olofsson [added WRGG Variables to DEVICE_VARS, squashed spi pinconf/mux, added emd1's gmac0 config,fix dtc warnings] Signed-off-by: Christian Lamparter

ath10k-firmware: fix mirror hash

2020-01-24T07:21:04Z

Fix PKG_MIRROR_HASH hash mismatch. Fixes: 641a93f0f226 ("ath10k-firmware: update wave 1 firmware to 10.2.4-1.0-00047") Signed-off-by: DENG Qingfang [added missing commit description] Signed-off-by: Petr Štetiar

ipq40xx: add support for EZVIZ CS-W3-WD1200G EUP

2020-01-12T14:57:58Z

Hardware: SOC: Qualcomm IPQ4018 RAM: 128 MB Nanya NT5CC64M16GP-DI FLASH: 16 MB Macronix MX25L12805D ETH: Qualcomm QCA8075 (4 Gigabit ports, 3xLAN, 1xWAN) WLAN: Qualcomm IPQ4018 (2.4 & 5 Ghz) BUTTON: Shared WPS/Reset button LED: RGB Status/Power LED SERIAL: Header J8 (UART, Left side of board). Numbered from top to bottom: (1) GND, (2) TX, (3) RX, (4) VCC (White triangle next to it). 3.3v, 115200, 8N1 Tested/Working: * Ethernet * WiFi (2.4 and 5GHz) * Status LED * Reset Button (See note below) Implementation notes: * The shared WPS/Reset button is implemented as a Reset button * I could not find a original firmware image to reverse engineer, meaning currently it's not possible to flash OpenWrt through the Web GUI. Installation (Through Serial console & TFTP): 1. Set your PC to fixed IP 192.168.1.12, Netmask 255.255.255.0, and connect to one of the LAN ports 2. Rename the initramfs image to 'C0A8010B.img' and enable a TFTP server on your pc, to serve the image 2. Connect to the router through serial (See connection properties above) 3. Hit a key during startup, to pause startup 4. type `setenv serverip 192.168.1.12`, to set the tftp server address 5. type `tftpboot`, to load the image from the laptop through tftp 6. type `bootm` to run the loaded image from memory 6. (If you want to return to stock firmware later, create an full MTD backup, e.g. using instructions here https://openwrt.org/docs/guide-user/installation/generic.backup#create_full_mtd_backup) 7. Transfer the 'sysupgrade' OpenWrt firmware image from PC to router, e.g.: `scp xxx-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/upgrade.bin` 8. Run sysupgrade to permanently install OpenWrt to flash: `sysupgrade -n /tmp/upgrade.bin` Revert to stock: To revert to stock, you need the MTD backup from step 6 above: 1. Unpack the MTD backup archive 2. Transfer the 'firmware' partition image to the router (e.g. mtd8_firmware.backup) 3. On the router, do `mtd write mtd8_firmware.backup firmware` Signed-off-by: Tom Brouwer [removed BOARD_NAME, OpenWRT->OpenWrt, changed LED device name to board name] Signed-off-by: Christian Lamparter