staging/jow/package/firmware, branch main

qualcommax: ipq807x: add support for Linksys HomeWRK

2025-01-15T10:25:01Z

Hardware specification: ======== SoC: Qualcomm IPQ8174 Flash: 1GB (Micron MT29F8G08ABBCAH4 or AMD/Spansion S34MS08G2) RAM: 2GB (2x Kingston B5116ECMDXGJD or ESMT M15T2G16128A DDR3L) Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075) WiFi1: 5GHz ax 2x2 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 (low band) WiFi2: 2.4GHz ax 2x2 (Qualcomm QCN5024 + Skyworks SKY85340-11) WiFi3: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 100-177 (high band) LED: 1x RGB status (NXP PCA9633) USB: 1x USB 3.0 Button: WPS, Reset Flash instructions: ======== 1. Installation from initramfs image using USB drive: Put the initramfs image on the USB drive: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Connect serial console (JST PH 6-pin connector): - 1 - GND, 2 - TX, 4 - RX (115200, 8N1, 3.3V) Stop u-boot and run: - usb start && usbboot 44000000 0 && bootm 44000000 Write firmware to the flash from initramfs: - sysupgrade -n openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-sysupgrade.bin or - ubiformat /dev/mtd22 -y -f openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-factory.ubi 2. USB recovery: Put the initramfs image on the USB: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Set u-boot env: - fw_setenv bootusb 'usb start && usbboot 44000000 0 && bootm 44000000' - fw_setenv bootcmd 'run bootusb; bootipq' Signed-off-by: Paweł Owoc Link: https://github.com/openwrt/openwrt/pull/17463 Signed-off-by: Robert Marko

qualcommax: ipq60xx: add TP-Link EAP610-Outdoor support

2025-01-12T15:54:51Z

TP-Link EAP610-Outdoor is a 802.11ax AP claiming AX1800 support. It is wall or pole mountable, and rated for outdoor use. It can only be powered via PoE. Specifications: --------------- * CPU: Qualcomm IPQ6018 Quad core Cortex-A53 * RAM: 512 MB * Storage: ESMT PSR1GA30DT 128MB NAND * Ethernet: * Gigabit RJ45 port with PoE input * WLAN: * 2.4GHz/5GHz * LEDs: * Multi-color System LED (Green/Amber) * Buttons: * 1x Reset * UART: 4-pin unpopulated header * 1.8 V level, Pinout 1 - TX, 2 - RX, 3 - GND, 4 - 1.8V Installation: ============= Web UI method ------------- Set up the device using the vendor's web UI. After that go to Management->SSH and enable the "SSH Login" checkbox. Select "Save". The connect to the machine via SSH: ssh -o hostkeyalgorithms=ssh-rsa Disable signature verification: cliclientd stopcs Rename the "-web-ui-factory" image to something less than 63 characters, maintaining the ".bin" suffix. * Go to System -> Firmware Update. * Under "New Firmware File", click "Browse" and select the image * Select "Update" and confirm by clicking "OK". If the update fails, the web UI should show an error message. Otherwise, the device should reboot into OpenWRT. TFTP method ----------- To flash via tftp, first place the initramfs image on the TFTP server. setenv serverip setenv ipaddr tftpboot tplink_eap610-outdoor-initramfs-uImage.itb bootm This should boot OpenWRT. Once booted, flash the sysupgrade.bin image using either luci or the commandline. The tplink2022 image format ============================ The vendor images of this device are packaged in a format that does not match any previous tplink formats. In order for flashing to work from the vendor's web UI, firmware updates need to be packaged in this format. The `tplink-mkimage-2022.py` is provided for this purpose. This script can also analyze vendor images, and extract the required "support" string. This string is checked by the vendor firmware, and images with a missing or incorrect string are rejected. Signed-off-by: Alexandru Gagniuc Link: https://github.com/openwrt/openwrt/pull/14922 Signed-off-by: Robert Marko

linux-firmware: package MediaTek MT7925 Bluetooth firmware

2024-12-22T17:33:40Z

`btusb` fails to start on MT7925 hardware without the appropriate firmware being loaded first: ``` bluetooth hci0: Direct firmware load for mediatek/mt7925/BT_RAM_CODE_MT7925_1_1_hdr.bin failed with error -2 bluetooth hci0: Falling back to sysfs fallback for: mediatek/mt7925/BT_RAM_CODE_MT7925_1_1_hdr.bin ``` Package firmware for MediaTek MT7925 Bluetooth from `linux-firmware`. Signed-off-by: Rani Hod Link: https://github.com/openwrt/openwrt/pull/17331 Signed-off-by: Hauke Mehrtens

ipq-wifi: update to Git HEAD (2024-12-18)

2024-12-22T10:36:23Z

4b849214b137 ipq8074: add TP-Link EAP620 HD v1 BDF Add board file for TP-Link EAP620 HD v1. Sourced from bdwlan_US.bin in stock firmware 1.1.0 Build 20211028 Signed-off-by: Shymon Samsel Link: https://github.com/openwrt/openwrt/pull/17254 Signed-off-by: Robert Marko

ipq807x: add support for TP-Link EAP620 HD v1

2024-12-22T10:36:23Z

Specifications: * SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 1.4 GHz) * Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13) * Serial Port: 3v3 TTL 115200n8 * Wi-Fi: QCA5054 (4x4 5 GHz 802.11ax) * Wi-Fi: QCN5024 (2x2 2.4 GHz 802.11b/g/n/ax) * Ethernet: AR8031 (10/100/1000BASE-T) * Flash: Winbond W29N01HZSINF (128 MiB) * LEDs: 1x Blue Status (GPIO 42 Active High) * Buttons: 1x Reset (GPIO 50 Active Low) Installation Instructions (Serial+TFTP): 1. Solder 4 pin header to JP1 and bridge pads of R58 and R62. 2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2, and 3 respectively. Be sure to crossover TX and RX. 3. Copy RAM firmware openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb to a TFTP server's root that is in the same subnet as your AP. 4. Power up the AP hold Ctrl+B in the serial console (115200n8) until autoboot is halted. 5. Run the following commands in the U-boot prompt: # setenv serverip # setenv ipaddr # tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb # bootm You may need to type Ctrl+C and Enter before running these commands to clear invisible characters from the buffer. 6. Run the following command in a terminal to copy the sysupgrade image to be installed (check IP address): $ scp -O openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/ 7. Activate the OpenWrt serial console and run the following commands: # cd /tmp # sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin 8. The AP will reboot and OpenWrt will be successfully installed. Known Issues: * 5GHz radio instability (upstream current ath11k build bug maybe?) Device support directly followed from EAP660HDv1 support Links: #15832 Signed-off-by: Shymon Samsel Link: https://github.com/openwrt/openwrt/pull/17254 Signed-off-by: Robert Marko

linux-firmware: ath11k: add QCA2066 firmware

2024-12-18T10:01:23Z

Add QCA2066 firmware package, ath11k is already supported. Signed-off-by: Chukun Pan Link: https://github.com/openwrt/openwrt/pull/17260 Signed-off-by: Robert Marko

lantiq/xrx200: move 8M flash devices to a small flash subtarget

2024-12-15T23:59:55Z

Images for xrx200 8M flash are either not building due to image size (TD-W8970, TD-W8980) or building such that the available free space in the overlayfs is too little to be useful. To keep images for these devices buildable, move them into a small flash variant of the xrx200 subtarget. As these devices are NOR flash only, remove NAND and UBI references from the kernel config to gain some additional image size reduction. The apparent 8M flash devices Arcadyan VGV7510KW22-brn, Arcadyan VGV7519-brn and Lantiq Easy80920-nor seem to exist in order to create special "factory" installation images for these devices (which actually have larger flash: 16MB for the Arcardyan devices; 64MB for the Lantiq device). As a considerable amount of surgery would appear to be required to the uboot-lantiq package structure to separate the "factory" from the "sysupgrade" device recipes for these devices they remain in the xrx200 target - if factory images aren't now created, 23.05.x factory images should suffice for initial installation. Tested on: Netgear DM200, TP-Link TD-W8980, AVM Fritz7490 (xrx200 subtarget: image build only) Fixes: https://github.com/openwrt/openwrt/issues/16761 Signed-off-by: Andrew MacIntyre Link: https://github.com/openwrt/openwrt/pull/17113 Signed-off-by: Hauke Mehrtens

qualcommax: ipq60xx: add Linksys MR7350 support

2024-12-07T15:00:58Z

Linksys MR7350 is a 802.11ax Dual-band router/AP. Specifications: * CPU: Qualcomm IPQ6000 Quad core Cortex-A53(A73) 1.5GHz * RAM: 512MB of DDR3 * Storage: 256Mb NAND * Ethernet: 5x1G RJ45 ports (QCA8075) * WLAN: * 2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5052 2x2@80MHz or 802.11a/b/g/n/ac/ax 1201 Mbps PHY rate * LED-s: * RGB system led * USB blue led * Buttons: 1x Soft reset 1x WPS * Power: 12V DC Jack Installation instructions: Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup. Login with your admin password. The default password can be found on a sticker under the device. To enter into the support mode, click on the “CA” link and the bottom of the page. Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button. Click start. Ignore all the prompts and warnings by click “yes” in all the popups. The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device. Then you would need to write openwrt to the other partition for it to work - First Check booted partition: fw_printenv -n boot_part - Change the partition: fw_setenv boot_part 1 or fw_setenv boot_part 2 depending on the current partition - Then install Openwrt to the other partition if booted in slot 1: mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin alt_kernel - If in slot 2: mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin kernel Co-Authored-by: Chukun Pan Co-Authored-by: Robert Marko Signed-off-by: Vladyslav Andreichykov Link: https://github.com/openwrt/openwrt/pull/14807 Signed-off-by: Robert Marko

qualcommax: ipq60xx: add Qihoo 360V6 support

2024-12-06T09:59:38Z

Specifications: SoC: Qualcomm IPQ6000 1.5GHz RAM: NTCC256M16ER-EK 512MiB Flash: W29N01HZSINA 128MiB ETH: QCA8075 (3x LAN, 1x WAN) WLAN1: 2.4GHz 802.11b/g/n/ax 2x2 WLAN2: 5GHz 802.11a/n/ac/ax 2x2 Power: DC 12V 1.5A Button: Reset, Wps USB: 1x 2.0 Flash instructions: 1. Download the initramfs image, rename it to initramfs.itb, host it with the tftp server. 2. Interrupt U-Boot and run these commands: tftpboot initramfs.itb bootm 3. After openwrt boots up, use scp or luci web to upload sysupgrade.bin to upgrade. Signed-off-by: Chukun Pan Link: https://github.com/openwrt/openwrt/pull/15940 Signed-off-by: Robert Marko

ipq-wifi: update to version 2024-11-28

2024-12-06T09:59:38Z

Contains following updates: * ipq8074: add TP-Link_deco-x80-5g BDF * ipq6018: add BDF for Qihoo 360V6 Signed-off-by: Chukun Pan Link: https://github.com/openwrt/openwrt/pull/15940 Signed-off-by: Robert Marko