staging/linusw/package/firmware, branch master

linux-firmware: update to 20260110

2026-01-30T15:51:32Z

% log --no-merges --pretty=oneline --abbrev-commit 20260110...20251125 ff2b45687e73 linux-firmware: update firmware for MT7925 WiFi device 1e133c2d1d75 mediatek MT7925: update bluetooth firmware to 20260106153314 2f9b243612ae mediatek MT7920: update bluetooth firmware to 20260105151350 1e92dbe4b49c mediatek MT7922: update bluetooth firmware to 20260106153735 b9a690370724 linux-firmware: update firmware for MT7922 WiFi device 0405e4a1ba66 Mellanox: Add new mlxsw_spectrum firmware xx.2016.3900 10d9e8e00e04 amdgpu: Update dcn314, dcn315 firmware to 0.1.42.0 21d69f404447 qcom: Update DSP firmware for sa8775 platform fa860a865341 QCA: Add Bluetooth firmware for QCC2072 uart interface 3692c4d6e677 i915: Xe3p_LPD DMC v2.33 b69f261cdedf qcom: Update DSP firmware for qcs8300 platform 5e60a4ec91ed linux-firmware: update firmware for MT7920 WiFi device 3ff97fca3ccc qcom: Update aic100 firmware files b85e1561bdfc qca: Update Bluetooth WCN6750 1.1.3-00100 firmware to 1.1.3-00105 acf533d4b3d7 firmware: Revert kernel_boot.elf due to license compliance issue f8a6723505e9 linux-firmware: add firmware for an8811hb 2.5G ethernet phy 2a6b361888e8 i915: Xe3LPD_3002 DMC v2.28 81368cb84b87 i915: Xe3LPD DMC v2.33 c360f595d977 intel_vpu: Add firmware for 50xx NPUs and update older ones 13786e87c7e9 linux-firmware: Update AMD SEV firmware 993573ac3dc6 amdgpu: DMCUB updates for various ASICs 19b55776b5b5 qcom: venus-5.4: fix ELF segment alignment to 4 bytes e56e0a4c8985 mediatek MT7925: update bluetooth firmware to 20251210093205 9ba3cd479466 linux-firmware: update firmware for MT7925 WiFi device 56bb432a65bc rcar_gen4_pcie: add firmware for Renesas R-Car Gen4 PCIe controller 154d3ad0864a qcom: Update CDSP firmware for qcm6490 platform 39fdaba4a719 rtl_bt: Update RTL8852BT/RTL8852BE-VT BT USB FW to 0x488C_DB55 f383a26428bf linux-firmware: Add firmware file for Intel Scorpius core fed51005f935 rtw89: 8852b: update fw to v0.29.29.15 fe9e5c89d5e8 cirrus: cs35l41: Update firmware and tuning for various HP laptops 1466bd681b4c cirrus: cs35l41: Add support for new HP Clipper laptop 950e89fddc4c qcom: drop compatibility a640_zap.mdt symlink 8715f3da4832 qcom: add version for a530v3_gpmu.fw2 3b34b3b938be xe: Update GUC to v70.55.3 for BMG, PTL 0a041632c156 iwlwifi: add Bz/Sc FW for core101-82 release 41b492fc7464 iwlwifi: Add Sc/Gf firmware for core101-82 release 8e39678cd6fb iwlwifi: update ty/So/Ma firmwares for core101-82 release 06bee1b5023d iwlwifi: update cc/Qu/QuZ firmwares for core101-82 release 9c9bdaab22a7 amdgpu: DMCUB updates for various ASICs d718d6300100 qcom: Add firmwares for sm8150 GPU 42e9d5a5994c qcom: Add firmwares for sm8450 GPU 30979b116b5c qcom: Add firmwares for sm8550 GPU 1304566db9cc qcom: Add firmwares for sm8650 GPU 3d89ec352d12 qcom: Add firmwares for sm8750 GPU 1d02df5c1ada Makefile: add licence header 9eca984de60d ath10k: WCN3990 hw1.0: update board-2.bin 89ef5c5da944 ath10k: QCA9888 hw2.0: update board-2.bin e6e77dccf149 ath10k: QCA4019 hw1.0: update board-2.bin 1774b2a25c75 cirrus: cs35l41: Add support for new HP laptops 3d5c8135206c Revert "amdgpu: update GC 11.5.0 firmware" e399bb332bda linux-firmware: Update amd-ucode copyright information 2b318c8e4159 linux-firmware: Update AMD cpu microcode c56e10ea830f linux-firmware: Update firmware file for Intel Scorpius core ee03c5fb3d99 linux-firmware: Update firmware file for Intel BlazarIGfP core 70a4bb64e5b3 linux-firmware: Update firmware file for Intel BlazarI core de8211b56b76 linux-firmware: Update firmware file for Intel BlazarU-HrPGfP core 4d8ef73cb73e linux-firmware: Update firmware file for Intel BlazarU core 15f854368441 ath11k: QCA6698AQ hw2.1: update to WLAN.HSP.1.1-04866-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1 b38214c8f31c ath11k: QCA2066 hw2.1: update board-2.bin c277a009eb05 qcom: update ADSP firmware for x1e80100 platform, change the license 6e06e5eac797 qcom: reorder ADSP, CDSP firmware entries for qcs8300 in WHENCE 9db3ba0dbc95 Reapply "amdgpu: update SMU 14.0.3 firmware" 5698af42f16e Revert "amdgpu: update SMU 14.0.3 firmware" baf6c2f67a24 Revert "amdgpu: update GC 10.3.6 firmware" c092c7487eb7 Revert "amdgpu: update GC 11.5.1 firmware" 5b890c92e78b linux-firmware: update firmware for MT7925 WiFi device 474cca8b3fd3 mediatek MT7925: update bluetooth firmware to 20251124093155 214b4374c0e9 intel_vpu: Update NPU firmware c91948d8a672 WHENCE: fix version string for video firmware 095130d8e395 qcom: vpu: update video firmware binary for SM8250 323507dc0c43 xe: Update GUC to v70.54.0 for BMG, PTL Build system: x86/64 Build-tested: x86/64-glibc Run-tested: x86/64-glibc (Intel N150) Signed-off-by: John Audia Link: https://github.com/openwrt/openwrt/pull/21497 Signed-off-by: Hauke Mehrtens

ipq-wifi: Add entry for TP-Link TL-WA1201 v2

2026-01-28T11:05:55Z

Add IPQ Wifi entry for ath79 TP-Link TL-WA1201 v2. Signed-off-by: Christoph Krapp Link: https://github.com/openwrt/openwrt/pull/21736 Signed-off-by: Robert Marko

ipq-wifi: update to Git HEAD (2026-01-28)

2026-01-28T11:02:27Z

88514e5aab3e qca9888: add bdf for TP-Link TL-WA1201 v2 Signed-off-by: Robert Marko

qualcommax: ipq807x: add support for TCL LINKHUB HH500V

2026-01-25T21:21:58Z

TCL LINKHUB HH500V also known as Vodafone Gigacube B157 is a dual band 802.11ax 5G NR CPE with an FXS port. Specifications: * SoC: Qualcomm IPQ8072A * RAM: 1024 MB * NAND flash: 256MB NAND (MT29F2G08ABBGAH4) * NOR flash: 64MB NOR (MX25U25635F) - only in some variants * WiFi 5G: Qualcomm QCN5054 * WiFi 2.4G: Qualcomm QCN5024 * Ethernet 2.5G: Qualcomm QCA8081 * Ethernet 1G: Qualcomm QCA8075 * Modem: GosunCn GM800 (Qualcomm Snapdragon X55) * SIM: 1 nano-SIM card slot * Buttons: Power, Reset, WPS * LEDs: Power (B/R), WiFi (B), 4G (B/Y/R), 5G (B/Y/R) * VoIP: 1 FXS RJ11 port (not supported in OpenWrt) * Power: 12V, 3A UART serial console: * 115200,8N1,1.8V * Three unmarked test points next to QJ2012A: +---------+ | QJ2012A | +---------+ o TX o GND o RX o o o Installation via OEM firmware: * Use the following process to obtain root ssh access https://forum.openwrt.org/t/150371/24 * Connect using root with no password on port 42000 * Optionally for serial bootloader access run : fw_setenv bootdelay=3 * SCP factory.bin to /tmp * Run: sysupgrade -n /tmp/factory.bin Installation via serial console and OEM firmware:: * Use console to access OEM firmware shell * Proceed with SCP & sysupgrade as described above Other notes: * This device uses active partition rotation * Some versions (TCL branded?) have a NOR chip in addition to NAND * The above is supported by u-boot patching DT partitions * DT patching does NOT occur on tftpboot/bootm * Modem is detected as foxconn-sdx55 by kernel (same VID/PID) * This works OK-ish and should be improved if we can get OEM modem details Signed-off-by: Milan Krstic Link: https://github.com/openwrt/openwrt/pull/19182 Signed-off-by: Robert Marko

qualcommax: ipq60xx: add support for TP-Link EAP620HD v3

2026-01-25T15:17:08Z

Specifications: * SoC: Qualcomm IPQ6018/AP-CP03-C1 (64-bit Quad-core Arm Cortex-A53 @ 1.2 GHz) * RAM: 2x Zentel A3T4GF40BBF-HP (1 GiB DDR3-1866 (13-13-13)) * Serial Port: 1v8 TTL 115200n8 * Wi-Fi: Qualcomm QCN5022 (802.11ax/b/g/n) * Wi-Fi: Qualcomm QCN5052 (802.11ac/ax/n) * Ethernet: RTL8211FS (10/100/1000BASE-T) * Flash: GigaDevice PSR1GA30DT (128 MiB) * LEDs: 1x Blue Status (GPIO 35 Active High) * Buttons: 1x Reset (GPIO 9 Active Low) * FCCID: 2AXJ4EAP620HDV3 * UART: 4-pin unpopulated header by the J1 footprint Installation Instructions (Serial+TFTP): 1. Locate the J1 footprint which contains 4 unpopulated pins where starting from the arrow, the pins are TX, RX, VCC and GND respectively. 2. Connect a 1v8 TTL port to the 4 pins. Ensure RX and TX are crossed over. 3. Copy openwrt-qualcommax-ipq60xx-tplink_eap620-hd-v3-initramfs-uImage.itb to your TFTP server. 4. Power up the AP and hold Ctrl+B in the serial console (115200n8) until autoboot is halted. 5. Run the following commands in the U-boot prompt: IPQ6018# setenv serverip IPQ6018# setenv ipaddr IPQ6018# tftpboot 0x44000000 openwrt-qualcommax-ipq60xx-tplink_eap620-hd-v3-initramfs-uImage.itb IPQ6018# bootm 0x44000000 You may need to type Ctrl+C and Enter before running these commands to clear invisible characters from the buffer. 6. Run the following command in a terminal to copy the sysupgrade image to be installed (check IP address): $ scp -O openwrt-qualcommax-ipq60xx-tplink_eap620-hd-v3-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/ 7. Activate the OpenWrt serial console and run the following commands: # cd /tmp # sysupgrade -n openwrt-qualcommax-ipq60xx-tplink_eap620-hd-v3-squashfs-sysupgrade.bin 8. The AP will reboot and OpenWrt will be successfully installed. Installation Instructions (Web UI method): 1. Set up the device using the vendor's web UI. Navigate to Management->SSH and enable the "SSH Login" checkbox. Select "Save". 2. Connect to the machine via SSH: $ ssh -o hostkeyalgorithms=ssh-rsa 3. Disable signature verification: $ cliclientd stopcs 4. Rename the "-web-ui-factory" image to something less than 63 characters, maintaining the ".bin" suffix. 5. Go to System -> Firmware Update. Under "New Firmware File", click "Browse" and select the image. Select "Update" and confirm by clicking "OK". 6. If the update fails, the web UI should show an error message. Otherwise, the device should reboot into OpenWrt. Device support followed from EAP620HD v2 and eap6xx-outdoor for DTS. Links: openwrt/openwrt#18227 Signed-off-by: John Christoforidis Link: https://github.com/openwrt/openwrt/pull/21467 Signed-off-by: Robert Marko

ipq-wifi: update to Git HEAD (2026-01-24)

2026-01-25T10:39:25Z

38804f59fbb9 ci: add ath12k BDF-s d28bc0724dc6 ipq8074: add TCL LINKHUB HH500V BDF 8e1fb2f59893 ipq6018:add TP-Link EAP620 HD v3 BDF Add board file for TP-Link EAP620 HD v3. bdwlan_US.bin sourced from EAP620 HD(US)_V3_1.4.4 Build 20250718 stock firmware. Signed-off-by: Robert Marko

qualcommax: ipq60xx: add JDCloud RE-CS-02 support

2026-01-18T10:13:54Z

Specifications: SoC: Qualcomm IPQ6010 1.8GHz RAM: K4A4G165WF-BCTD x2 1GiB Flash: FORESEE 128GB/256GB eMMC ETH: 4x 1Gbps + 1x 2.5Gbps WLAN1: QCN5022 2.4GHz AX 2x2 WLAN2: QCN5052 5.8GHz AX 2x2 WLAN2: QCN9024 5.2GHz AX 4x4 Button: Reset, Screen, Wps Power: DC 12V 3A USB: 1x 3.0 Flash instructions: 1. Download the initramfs image, rename it to initramfs.itb, host it with the tftp server. 2. If the stock firmware version is 4.3.0.r4211 or higher, enter "jdmt018R" to interrupt U-Boot when the following statement appears: "disabled console and autoboot in 2 seconds" 3. Run these commands in U-Boot console: tftpboot initramfs.itb bootm 4. After openwrt boots up, use scp or luci web to upload sysupgrade.bin to upgrade. Signed-off-by: Chukun Pan Link: https://github.com/openwrt/openwrt/pull/19840 Signed-off-by: Robert Marko

qualcommax: ipq60xx: add JDCloud RE-SS-01 support

2026-01-17T15:18:13Z

Specifications: SoC: Qualcomm IPQ6000 1.2GHz RAM: NT52CB256MB16DP 512MiB Flash: FORESEE 64GB/128GB eMMC ETH: QCA8075 (3x LAN, 1x WAN) WLAN1: QCN5022 2.4GHz AX 2x2 WLAN2: QCN5052 5GHz AX 2x2 Power: DC 12V 2A Button: Reset, Wps USB: 1x 3.0 Flash instructions: 1. Download the initramfs image, rename it to initramfs.itb, host it with the tftp server. 2. If the stock firmware version is 4.3.0.r4211 or higher, enter "jdmt018R" to interrupt U-Boot when the following statement appears: "disabled console and autoboot in 2 seconds" 3. Run these commands in U-Boot console: tftpboot initramfs.itb bootm 4. After openwrt boots up, use scp or luci web to upload sysupgrade.bin to upgrade. Signed-off-by: Chukun Pan Link: https://github.com/openwrt/openwrt/pull/19780 Signed-off-by: Robert Marko

qoriq: add support for NXP T4240RDB board

2026-01-09T16:45:02Z

Hardware specs: - NXP T4240, 12C/24T @ 1.67 GHz - 3 × 2 GB DDR3 SO-DIMM - 128 MB NOR flash - 2 GB SLC NAND - SD card interface - PCIe: x4 and x8 - SATA 3 Gbps - 8 × 1 GbE - 4 × 10 GbE SFP - RTC This commit adds the sysupgrade and factory images for T4240RDB board in both variants: - nor: for booting and read whole system from NOR memory - sdboot: for booting and read whole system from SD card SD Card images install: - Burn image to sdcard. E.g: gunzip -c gunzip -c openwrt-qoriq-generic-fsl_T4240RDB-squashfs-sdcard.img.gz | \ sudo dd of=/dev/mmcblk0 conv=fsync,notrunc status=progress bs=4M && sync - Download lastest Cortina PHY firmware from NXP github [1], if you accept their EULA [2]. - Install Cortina PHY on image, E.g: dd if=cs4315-cs4340-PHY-ucode.txt of=/dev/mmcblk0 bs=1 seek=2M - Insert SD-Card to SD slot - Switch SW3.4 to OFF - Configre mac addresses from sticker in u-boot. E.g: setenv ethaddr 00:10:f3:3a:a8:66 setenv eth1addr 00:10:f3:3a:a8:67 setenv eth2addr 00:10:f3:3a:a8:68 setenv eth3addr 00:10:f3:3a:a8:69 setenv eth4addr 00:10:f3:3a:a8:6a setenv eth5addr 00:10:f3:3a:a8:6b setenv eth6addr 00:10:f3:3a:a8:6c setenv eth7addr 00:10:f3:3a:a8:6d setenv eth8addr 00:10:f3:3a:a8:6e setenv eth9addr 00:10:f3:3a:a8:6f setenv eth10addr 00:10:f3:3a:a8:70 setenv eth11addr 00:10:f3:3a:a8:71 saveenv - reset and boot NOR images install: - download and extract factory image on tftp server root - boot device and stop in u-boot (from nor or sd card u-boot) - configure server and ip address. E.g: setenv ipaddr 192.168.1.2 setenv serverip 192.168.1.1 - Download image and run flashing: tftpboot $loadaddr openwrt-qoriq-generic-fsl_T4240RDB-squashfs-factory-nor.bin protect off all erase $fwaddr +$filesize cp.b $loadaddr $fwaddr $filesize - Switch SW3.4 to ON - Switch SW3.1-3 to OFF - reboot - Do postprocessing (see bellow) NOR images post processing: - Configre mac addresses from sticker in u-boot. E.g: setenv ethaddr 00:10:f3:3a:a8:66 setenv eth1addr 00:10:f3:3a:a8:67 setenv eth2addr 00:10:f3:3a:a8:68 setenv eth3addr 00:10:f3:3a:a8:69 setenv eth4addr 00:10:f3:3a:a8:6a setenv eth5addr 00:10:f3:3a:a8:6b setenv eth6addr 00:10:f3:3a:a8:6c setenv eth7addr 00:10:f3:3a:a8:6d setenv eth8addr 00:10:f3:3a:a8:6e setenv eth9addr 00:10:f3:3a:a8:6f setenv eth10addr 00:10:f3:3a:a8:70 setenv eth11addr 00:10:f3:3a:a8:71 saveenv - boot - Download and refresh RCW stored in eeprom: tr '\0' '\377' < /dev/zero | dd bs=256 of=/sys/bus/i2c/devices/0-0050/eeprom cat /tmp/openwrt-qoriq-generic-fsl_T4240RDB-squashfs-rcw.bin > /sys/bus/i2c/devices/0-0050/eeprom - Download lastest Cortina PHY firmware from NXP github [1], if you accept their EULA [2]. - Install Cortina PHY on image, E.g: mtd write cs4315-cs4340-PHY-ucode.txt /dev/mtd4 - reset and boot [1] https://raw.githubusercontent.com/nxp-qoriq/qoriq-firmware-cortina/refs/tags/lf-6.12.34-2.1.0/cs4315-cs4340-PHY-ucode.txt [2] https://github.com/nxp-qoriq/qoriq-firmware-cortina/blob/lf-6.12.34-2.1.0/EULA.txt Signed-off-by: Pawel Dembicki Link: https://github.com/openwrt/openwrt/pull/10941 Signed-off-by: Stijn Tintel

ipq-wifi: rename BDF for EAP623-Outdoor HD v1

2026-01-08T10:18:23Z

BDF for EAP623-Outdoor HD v1 was renamed in the repo, but ipq-wifi was not updated to reflect that, so do it now to fix broken wifi. Fixes: #21432 Signed-off-by: Robert Marko