staging/lynxis/tools/Makefile, branch master

tools: cbootimage: depend on automake

2019-04-07T13:25:28Z

Fix missing aclocal reported by buildbot. Fixes: 8595bb0 ("tools: add cbootimage for tegra") Signed-off-by: Tomasz Maciej Nowak

tools: add cbootimage-configs for tegra

2019-04-06T12:48:46Z

This provides board configuraion tables for various Tegra boards needed by cbootimage tool to create flashable bootloader images. Signed-off-by: Tomasz Maciej Nowak

tools: add cbootimage for tegra

2019-04-06T12:48:46Z

Tegra BCT and bootable flash image generator/compiler >From documentation: This project provides a tool which compiles BCT (Boot Configuration Table) images to place into the boot flash of a Tegra-based device. The tool will either: a) Compile a textual representation of a BCT into a binary image. b) Generate an entire boot image from a previously compiled BCT and a bootloader binary. Signed-off-by: Tomasz Maciej Nowak

tools: squashfskit4 should only depend on coreutils on non-linux systems

2019-03-03T19:58:52Z

Signed-off-by: Felix Fietkau

tools/squashfskit: fix version detection on non-linux system

2019-03-03T18:45:10Z

gnu date is present in our staging_dir which means squashfskit will fail to build. Prevent also a race condition if coreutils is build after squashfskit. To prevent a race condition, depend on coreutils. Acked-by: Kevin Darbyshire-Bryant Signed-off-by: Felix Fietkau Signed-off-by: Alexander Couzens

tools: migrate from squashfs4 to squashfskit4

2019-02-28T00:38:46Z

squashfskit is a fork of the squashfs-tools. squashfskit creates reproducible filesystems and includes many of the distro patches. Signed-off-by: Alexander Couzens Tested-by: Paul Spooren

gemini: Generate harddisk image for DNS-313

2019-02-20T17:51:31Z

This makes OpenWrt build an Ext2+Ext4 partitioned image for the D-Link DNS-313 with two blank partitions, a boot partition on /dev/sda3 and a rootfs partition on /dev/sda4. This uses the methods already used in apm821xx including the tricks to convert the generated Ext2 filesystem partition to version 1 so that the firmware bootloader will properly recognize it. We patch a bit around the build files to make sure we get the rootfs size set and that genext2fs is properly built. Tested on the D-Link DNS-313. Signed-off-by: Christian Lamparter [Fixing and tricksing] Signed-off-by: Linus Walleij

tools/sed: fix incorrect dependency.

2019-01-22T10:28:49Z

sed shall depend on xz instead of xz depends on sed. Signed-off-by: Kuang Rufan

tools: add zip utility

2019-01-15T18:11:53Z

One image requires a zip compressed image, so add the zip util found in the packages feed, and extend it with some useful debian patches. Signed-off-by: Mathias Kresin

tools: patch: Fix build by not modifing Makefile.am

2018-10-14T14:47:15Z

A new test case was adding in one of the patches fixing a problem, this also included a change in the test/Makefile.am to add this test case. The build system detected a change in the Makefile.am and wants to regenerate the Makefile.in, but this fails because automake-1.15 is not installed yet. As automake depends on patch being build first, make sure we do not modify the Makefile.am. This fixes build problem seen by the build bots. Fixes: 4797dddfde6 ("patch: apply upstream cve fixes") Signed-off-by: Hauke Mehrtens