staging/neocturne/package/firmware, branch main

firmware: intel-microcode: update to 20240531

2024-06-15T09:20:13Z

Debian changelog: intel-microcode (3.20240531.1) unstable; urgency=medium * New upstream microcode datafile 20240531 * Fix unspecified functional issues on Pentium Silver N/J5xxx, Celeron N/J4xxx * Updated Microcodes: sig 0x000706a1, pf_mask 0x01, 2024-04-19, rev 0x0042, size 76800 * source: update symlinks to reflect id of the latest release, 20240531 -- Henrique de Moraes Holschuh Sat, 01 Jun 2024 11:49:47 -0300 intel-microcode (3.20240514.1) unstable; urgency=medium * New upstream microcode datafile 20240514 * Mitigations for INTEL-SA-01051 (CVE-2023-45733) Hardware logic contains race conditions in some Intel Processors may allow an authenticated user to potentially enable partial information disclosure via local access. * Mitigations for INTEL-SA-01052 (CVE-2023-46103) Sequence of processor instructions leads to unexpected behavior in Intel Core Ultra Processors may allow an authenticated user to potentially enable denial of service via local access. * Mitigations for INTEL-SA-01036 (CVE-2023-45745, CVE-2023-47855) Improper input validation in some Intel TDX module software before version 1.5.05.46.698 may allow a privileged user to potentially enable escalation of privilege via local access. * Fix for unspecified functional issues on 4th gen and 5th gen Xeon Scalable, 12th, 13th and 14th gen Intel Core processors, as well as for Core i3 N-series processors. * Updated microcodes: sig 0x000806f8, pf_mask 0x87, 2024-02-05, rev 0x2b0005c0, size 581632 sig 0x000806f7, pf_mask 0x87, 2024-02-05, rev 0x2b0005c0 sig 0x000806f6, pf_mask 0x87, 2024-02-05, rev 0x2b0005c0 sig 0x000806f5, pf_mask 0x87, 2024-02-05, rev 0x2b0005c0 sig 0x000806f4, pf_mask 0x87, 2024-02-05, rev 0x2b0005c0 sig 0x000806f8, pf_mask 0x10, 2024-02-05, rev 0x2c000390, size 614400 sig 0x000806f6, pf_mask 0x10, 2024-02-05, rev 0x2c000390 sig 0x000806f5, pf_mask 0x10, 2024-02-05, rev 0x2c000390 sig 0x000806f4, pf_mask 0x10, 2024-02-05, rev 0x2c000390 sig 0x00090672, pf_mask 0x07, 2023-12-05, rev 0x0035, size 224256 sig 0x00090675, pf_mask 0x07, 2023-12-05, rev 0x0035 sig 0x000b06f2, pf_mask 0x07, 2023-12-05, rev 0x0035 sig 0x000b06f5, pf_mask 0x07, 2023-12-05, rev 0x0035 sig 0x000906a3, pf_mask 0x80, 2023-12-05, rev 0x0433, size 222208 sig 0x000906a4, pf_mask 0x80, 2023-12-05, rev 0x0433 sig 0x000906a4, pf_mask 0x40, 2023-12-07, rev 0x0007, size 119808 sig 0x000b0671, pf_mask 0x32, 2024-01-25, rev 0x0123, size 215040 sig 0x000b06e0, pf_mask 0x11, 2023-12-07, rev 0x0017, size 138240 sig 0x000c06f2, pf_mask 0x87, 2024-02-05, rev 0x21000230, size 552960 sig 0x000c06f1, pf_mask 0x87, 2024-02-05, rev 0x21000230 * source: update symlinks to reflect id of the latest release, 20240514 -- Henrique de Moraes Holschuh Thu, 16 May 2024 21:40:52 -0300 Signed-off-by: Christian Lamparter

linux-firmware: Update to version 20240513

2024-05-28T20:04:34Z

This updates the following firmware files: airoha-en8811h-firmware/lib/firmware/airoha/EthMD32.DSP.bin airoha-en8811h-firmware/lib/firmware/airoha/EthMD32.dm.bin amdgpu-firmware/ (Many files) ibt-firmware/lib/firmware/intel/ibt-0040-0041.sfi ibt-firmware/lib/firmware/intel/ibt-0040-1020.sfi ibt-firmware/lib/firmware/intel/ibt-0040-1050.sfi ibt-firmware/lib/firmware/intel/ibt-0040-2120.sfi ibt-firmware/lib/firmware/intel/ibt-0040-4150.sfi ibt-firmware/lib/firmware/intel/ibt-0041-0041.sfi ibt-firmware/lib/firmware/intel/ibt-0180-0041.sfi ibt-firmware/lib/firmware/intel/ibt-0180-1050.sfi ibt-firmware/lib/firmware/intel/ibt-0180-4150.sfi ibt-firmware/lib/firmware/intel/ibt-0291-0291.ddc ibt-firmware/lib/firmware/intel/ibt-0291-0291.sfi ibt-firmware/lib/firmware/intel/ibt-1040-0041.sfi ibt-firmware/lib/firmware/intel/ibt-1040-1020.sfi ibt-firmware/lib/firmware/intel/ibt-1040-1050.sfi ibt-firmware/lib/firmware/intel/ibt-1040-2120.sfi ibt-firmware/lib/firmware/intel/ibt-1040-4150.sfi ibt-firmware/lib/firmware/intel/ibt-17-16-1.sfi ibt-firmware/lib/firmware/intel/ibt-17-2.sfi ibt-firmware/lib/firmware/intel/ibt-18-16-1.sfi ibt-firmware/lib/firmware/intel/ibt-18-2.sfi ibt-firmware/lib/firmware/intel/ibt-19-0-0.sfi ibt-firmware/lib/firmware/intel/ibt-19-0-1.sfi ibt-firmware/lib/firmware/intel/ibt-19-0-4.sfi ibt-firmware/lib/firmware/intel/ibt-19-16-4.sfi ibt-firmware/lib/firmware/intel/ibt-19-240-1.sfi ibt-firmware/lib/firmware/intel/ibt-19-240-4.sfi ibt-firmware/lib/firmware/intel/ibt-19-32-0.sfi ibt-firmware/lib/firmware/intel/ibt-19-32-1.sfi ibt-firmware/lib/firmware/intel/ibt-19-32-4.sfi ibt-firmware/lib/firmware/intel/ibt-20-0-3.sfi ibt-firmware/lib/firmware/intel/ibt-20-1-3.sfi ibt-firmware/lib/firmware/intel/ibt-20-1-4.sfi iwlwifi-firmware-ax200/lib/firmware/iwlwifi-cc-a0-77.ucode iwlwifi-firmware-ax201/lib/firmware/iwlwifi-QuZ-a0-hr-b0-77.ucode iwlwifi-firmware-ax210/lib/firmware/iwlwifi-ty-a0-gf-a0.pnvm iwlwifi-firmware-be200/lib/firmware/iwlwifi-gl-c0-fm-c0.pnvm iwlwifi-firmware-iwl9000/lib/firmware/iwlwifi-9000-pu-b0-jf-b0-46.ucode iwlwifi-firmware-iwl9260/lib/firmware/iwlwifi-9260-th-b0-jf-b0-46.ucode mt7921bt-firmware/lib/firmware/mediatek/BT_RAM_CODE_MT7961_1_2_hdr.bin mt7922bt-firmware/lib/firmware/mediatek/BT_RAM_CODE_MT7922_1_1_hdr.bin rtl8852ce-firmware/lib/firmware/rtw89/rtw8852c_fw.bin Signed-off-by: Hauke Mehrtens

ppfe-firmware: Bump to lf-6.6.3-1.0.0

2024-05-25T18:18:23Z

Bump ppfe-firmware package to lf-6.6.3-1.0.0 Signed-off-by: Pawel Dembicki

ls-rcw: Bump to lf-6.6.3-1.0.0

2024-05-25T18:18:23Z

Bump ls-rcw package to lf-6.6.3-1.0.0. Signed-off-by: Pawel Dembicki

ls-ddr-phy: bump to lf-6.6.3-1.0.0

2024-05-25T18:18:23Z

Bump ls-ddr-phy to version lf-6.6.3-1.0.0. Signed-off-by: Pawel Dembicki

fman-ucode: Bump to lf-6.6.3-1.0.0

2024-05-25T18:18:23Z

Bump fman-ucode to version lf-6.6.3-1.0.0. Signed-off-by: Pawel Dembicki

qualcommax: ipq807x support Netgear Orbi Pro SXK80

2024-05-22T12:51:36Z

This commit adds support for Netgear Orbi Pro SXR80 and SXS80 (collectively known as SXK80) Specifications: --------------- * CPU: Qualcomm IPQ8074A Quad core Cortex-A53 * RAM: 1024MB * Storage: SPI-NAND 512 MiB (Winbond W29N04GZ) * Ethernet: 4x 1G RJ45 ports (QCA8075) 1x 2.5G RJ45 LAN/WAN (QCA8081) * WLAN: - 2.4 GHz: Qualcomm QCN5024 4x4 - 2x 5 GHz: Qualcomm QCN5054 4x4 (second radio high channels only) * LEDs: - Power: (Green and red) - Front: (Blue, green, red and white) * Buttons: - 1x Soft reset - 1x Sync/WPS * Power: 12V DC Jack Installation instructions (Telnet): ----------------------------------- *Note, this guide assumes SXR80, for SXS80 change the firmware file name as appropriate 1. Put firmware file openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb in root of TFTP server available at 192.168.1.10. 2. Enable telnet by going to http://[ip of device]/debug.htm and clicking on the tickbox 'Enable telnet' 3. Telnet into the device and login using the same username and password as the web interface: 4. Run the following command: `fw_setenv bootcmd 'env default -a; saveenv; reset'` 5. Reboot the router, once the web interface is available again re-enable telnet via http://[ip of device]/debug.htm and telnet into the device. 6. Run the following command: `fw_printenv` It should look similar to the below: ``` baudrate=115200 bootargs=console=ttyMSM0,115200n8 bootcmd=mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot bootdelay=2 ipaddr=192.168.1.1 netmask=255.255.255.0 serverip=192.168.1.10 soc_version_major=2 soc_version_minor=0 ``` **If you see the message:** `Warning: Bad CRC, using default environment` **DO NOT CONTINUE, YOU WILL BRICK YOUR DEVICE** 7. Run the following command: `fw_setenv originalboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot'` (This should match what's in the bootcmd variable displayed in step 6) 8. Run the following commands: ``` fw_setenv wrttftp 'mii write 0x0 0x0 0x800; sleep 1; nmrp; if tftpboot openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb; then bootm; fi; bootdni; boot_DNI_secureboot' fw_setenv wrtboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; nand read 0x40000000 0x1980000 0x06d00000; bootm 0x40000000' fw_setenv bootcmd 'run wrttftp' ``` 9. Ensure SXR/S device is attached via ethernet (LAN port) to the same ethernet segment as the TFTP server. 10. Reboot the device, it should reboot into OpenWrt and be available on 192.168.1.1 11. Once OpenWrt has booted, update the bootcmd using the following command: `fw_setenv bootcmd 'run wrtboot'` 12. Flash the sysupgrade image 13. It should boot into OpenWrt References to SXK80 GPL source: https://www.downloads.netgear.com/files/GPL/SXK80-V3.2.0.108_gpl_src.tar.bz2.zip Signed-off-by: Flole Systems Signed-off-by: Andrew Smith Link: https://github.com/openwrt/openwrt/pull/14939 Signed-off-by: Robert Marko

linux-firmware: realtek: update rtl8821ae firmware

2024-05-20T13:06:42Z

A newer version, rtl8821aefw_29.bin, has been available for over 7 years [1]. Let's use it. [1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit?id=f70e4df2b384d21e36a7c30a591639592692e0ec Signed-off-by: Rui Salvaterra

wireless-regdb: update to 2024.05.08

2024-05-19T13:17:44Z

Changes: 73529a8 Revert "wireless-regdb: Update and disable 5470-5730MHz band according to TPC requirement for Singapore (SG)" 87941e4 wireless-regdb: Update regulatory rules for Taiwan (TW) on 6GHz 33797ae wireless-regdb: update regulatory database based on preceding changes Signed-off-by: Yuu Toriyama

qualcommax: ipq807x: add support for Linksys MX8500

2024-05-16T18:27:36Z

Hardware specification: ======== SoC: Qualcomm IPQ8072A Flash: 512MB (Fidelix FMND4G08S3J-ID) RAM: 1GB (2x Kingston DDR3L D2516ECMDXGJD) Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C) Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075) WiFi1: 6GHz ax 4x4 (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229 WiFi2: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-177 WiFi3: 2.4GHz ax 4x4 (Qualcomm QCN5024 + Skyworks SKY8340-11) IoT: Bluetooth 5, Zigbee and Thread (NXP K32W041) LED: 1x RGB status (NXP PCA9633) USB: 1x USB 3.0 Button: WPS, Reset Flash instructions: ======== 1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin image. More details can be found here: https://www.linksys.com/support-article?articleNum=47547 After first boot check actual partition: - fw_printenv -n boot_part and install firmware on second partition using command in case of 2: - mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel and in case of 1: - mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel 2. Installation using serial connection from OEM firmware (default login: root, password: admin): - fw_printenv -n boot_part In case of 2: - flash_erase /dev/mtd21 0 0 - nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin or in case of 1: - flash_erase /dev/mtd23 0 0 - nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin After first boot install firmware on second partition: - mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel or: - mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel 3. Installation from initramfs image using USB drive: Put the initramfs image on the USB drive: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda Stop u-boot and run: - usb start && usbboot $loadaddr 0 && bootm $loadaddr Write firmware to the flash from initramfs: - mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel and: - mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel 4. Back to the OEM firmware: - mtd -e kernel -n write FW_MX8500_1.0.11.208937_prod.img kernel and: - mtd -r -e alt_kernel -n write FW_MX8500_1.0.11.208937_prod.img alt_kernel 5. USB recovery: Put the initramfs image on the USB: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda Set u-boot env: - fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr' - fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi' AQR firmware: ======== 1. Firmware loading: To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function. To do this, you need to modify u-boot env: With USB recovery: - fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi' and without: - fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi' 2. Firmware updating: Newer firmware (AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld) is available in the latest OEM firmware. To load this firmware via u-boot, we need to add the MBN header and update 0:ethphyfw partition. For MBN header we can use script from this repository: https://github.com/testuser7/aqr_mbn_tool - python aqr_mbn_tool.py AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld To update partition we need to install kmod-mtd-rw package first: - insmod mtd-rw.ko i_want_a_brick=1 - mtd -e /dev/mtd26 -n write aqr_fw.mbn /dev/mtd26 Signed-off-by: Paweł Owoc Link: https://github.com/openwrt/openwrt/pull/14883 Signed-off-by: Robert Marko