staging/noltari/package/boot, branch master

ramips: add support for SNR-CPE-ME2-SFP

2023-03-08T22:44:59Z

SNR-CPE-ME2-SFP is a wireless router with SFP cage manufactured by SNR/NAG company. Specification: - SoC: MediaTek MT7621A - CPU: 880MHz - Flash: 16 MB (GD25Q127CSIG) - RAM: 256 MB - WLAN: 2.4 GHz, 5 GHz (MediaTek MT7615DN) - Ethernet: 4x 10/100/1000 Mbps - SFP cage (using RTL8211FS-CG) - USB 3.0 port - Power: 12 VDC, 2 A Flash instruction via TFTP: 1. Boot SNR-CPE-ME2 to recovery mode (press reset button and power on device, hold button for ~10 seconds) 2. Send firmware via TFTP client: TFTP Server address: 192.168.1.1 TFTP Client address: 192.168.1.131 3. Wait ~120 seconds to complete flashing 4. Do sysupgrade using web-interface MAC Addresses(stock) -------------------- +----------+------------------+-------------------+ | use | address | example | +----------+------------------+-------------------+ | Device | label | 6A:C4:DD:xx:xx:28 | | Ethernet | + 1 | 6A:C4:DD:xx:xx:29 | | 2g | + 2 | 6A:C4:DD:xx:xx:2A | | 5g | + 3 | 6A:C4:DD:xx:xx:2B | +----------+------------------+-------------------+ Notes: - Reading sfp eeprom is not supported [1] (driver issue). Stock image has the same situation. References: 1. https://forum.openwrt.org/t/mt7621-and-reading-sfp-eeprom/152249 Signed-off-by: Aleksey Nasibulin

mpc85xx: add support for Watchguard Firebox T10

2023-03-07T13:05:02Z

Hardware -------- SoC: Freescale P1010 RAM: 512MB FLASH: 1 MB SPI-NOR 512 MB NAND ETH: 3x Gigabite Ethernet (Atheros AR8033) SERIAL: Cisco RJ-45 (115200 8N1) RTC: Battery-Backed RTC (I2C) Installation ------------ 1. Patch U-Boot by dumping the content of the SPI-Flash using a SPI programmer. The SHA1 hash for the U-Boot password is currently unknown. A tool for patching U-Boot is available at https://github.com/blocktrron/t10-uboot-patcher/ You can also patch the unknown password yourself. The SHA1 hash is E597301A1D89FF3F6D318DBF4DBA0A5ABC5ECBEA 2. Interrupt the bootmenu by pressing CTRL+C. A password prompt appears. The patched password is '1234' (without quotation marks) 3. Download the OpenWrt initramfs image. Copy it to a TFTP server reachable at 10.0.1.13/24 and rename it to uImage. 4. Connect the TFTP server to ethernet port 0 of the Watchguard T10. 5. Download and boot the initramfs image by entering "tftpboot; bootm;" in U-Boot. 6. After OpenWrt booted, create a UBI volume on the old data partition. The "ubi" mtd partition should be mtd7, check this using $ cat /proc/mtd Create a UBI partition by executing $ ubiformat /dev/mtd7 -y 7. Increase the loadable kernel-size of U-Boot by executing $ fw_setenv SysAKernSize 800000 8. Transfer the OpenWrt sysupgrade image to the Watchguard T10 using scp. Install the image by using sysupgrade: $ sysupgrade -n Note: The LAN ports of the T10 are 1 & 2 while 0 is WAN. You might have to change the ethernet-port. 9. OpenWrt should now boot from the internal NAND. Enjoy. Signed-off-by: David Bauer

uboot-mediatek: mark all packages as hidden

2023-03-04T15:27:25Z

They are enabled by selecting devices. Fixes build errors when enabling extra devices without creating a new config from scratch. Signed-off-by: Felix Fietkau

kexec-tools: update to 2.0.26

2023-03-01T21:13:27Z

Release Notes: - 2.0.22: https://www.spinics.net/lists/kexec/msg26864.html - 2.0.23: https://www.spinics.net/lists/kexec/msg27693.html - 2.0.24: https://www.spinics.net/lists/kexec/msg28922.html - 2.0.25: https://lore.kernel.org/all/YuYl22cyGldQQc5m@vergenet.net/ - 2.0.26: https://www.spinics.net/lists/kexec/msg30743.html Remove upstreamed patch: - 001-arm-do-not-copy-magic-4-bytes-of-appended-DTB-in-zIm.patch Tested-by: Linhui Liu # x86_64 Signed-off-by: Nick Hainke

grub2: re-add test module

2023-02-26T21:22:48Z

It seems more hardware needs early load of firmware when initialised to work properly (at least Intel hardware). One of previous case is CPU microcode, which this series[1] tried to change. The second one is Intel graphics IC, which needs firmware for controlling DMC circuit (switch conncted display to DC6 power state). As it stands, the i915 module is built-in and it seems the hardware can't cope with firmware loaded later from rootfs, it needs to be supplied when the module is loaded. Unfortunately we need bootloader to handle the load of firmware in this case, but as previously mentioned series[1], there was an error when initrd was hardcoded, instead of testing existence for it and then loading. To remedy this in later the 55b808e0c4be ('x86: image: add test module to bootloader') was commited. Which was later accidentally dropped when grub2 image creation was moved to packages. Therefore bring back test module, so we can test for cases of existing firmware in grub.cfg. 1. https://patchwork.ozlabs.org/project/openwrt/cover/20181120162044.16371-1-tomek_n@o2.pl Fixes: 5a5df62d95f5 ("x86/grub2: move grub2 image creation to package") Signed-off-by: Tomasz Maciej Nowak

mvebu: add support for Buffalo LinkStation LS220DE

2023-02-26T21:22:48Z

The Buffalo LinkStation LS220DE is a dual bay NAS, based on Marvell Armada 370 Hardware: SoC: Marvell Armada 88F6707 CPU: Cortex-A9 800 MHz, 1 core Flash 1: SPI-NOR 1 MiB (U-Boot) Flash 2: NAND 512 MiB (OS) RAM: DDR3 256 MiB Ethernet: 1x 1GbE USB: 1x 2.0 SATA: 2x 3Gb/s LEDs/Input: 5x / 2x (1x button, 1x slide-switch) Fan: 1x casing Flash instructions, from hard drive: 1. Get access to the "boot" partition at the hard drive where the stock firmware is installed. It can be done with acp-commander or by plugging the hard drive to a computer. 2. Backup the stock uImage: mv /boot/uImage.buffalo /boot/uImage.buffalo.bak 3. Move and rename the Openwrt initramfs image to the boot partition: mv openwrt-initramfs-kernel.bin /boot/uImage.buffalo 4. Power on the Linkstation with the hardrive inside. Now Openwrt will boot, but still not installed. 5. Connect via ssh to OpenWrt: ssh root@192.168.1.1 6. Rename boot files inside boot partition mount -t ext3 /dev/sda1 /mnt mv /mnt/uImage.buffalo /mnt/uImage.buffalo.openwrt.bak mv /mnt/initrd.buffalo /mnt/initrd.buffalo.bak 7. Format ubi partitions at the NAND flash ("kernel_ubi" and "ubi"): ubiformat /dev/mtd0 -y ubidetach -p /dev/mtd1 ubiformat /dev/mtd1 -y 8. Flash the sysupgrade image: sysupgrade -n openwrt-squashfs-sysupgrade.bin 9. Wait until it finish, the device will reboot with OpenWrt installed on the NAND flash. Restore the stock firmware: 1. Take the hard drive used for the installation and restore boot backup files to their original names: mount -t ext3 /dev/sda1 /mnt mv /mnt/uImage.buffalo.bak /mnt/uImage.buffalo mv /mnt/initrd.buffalo.bak /mnt/initrd.buffalo 2. Boot from the hard drive and perform a stock firmware update using the Buffalo utility. The NAND will be restored to the original state. Signed-off-by: Daniel González Cabanelas

ramips: add support for Senao Engenius EPG600

2023-02-18T15:55:35Z

FCC ID: A8J-EPG600 Engenius EPG600 is an indoor wireless router with 1 Gb ethernet switch, dual-band wireless, internal antenna plates, USB, and phone lines (not supported) this board is a Senao device: the hardware is equivalent to EnGenius ESR600 (except for phone lines) the software is Senao SDK which is based on openwrt and uboot which uses the legacy Senao header with Vendor / Product IDs to verify the firmware upgrade image. **Specification:** - MT7620 SOC MIPS 24kec, 2.4 GHz WMAC, 2x2 - RT5592N WLAN PCI chip, 5 GHz, 2x2 - QCA8337N Gb SW RGMII GbE, SW P0 -- SOC P5, 5 LEDs - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 64 MB RAM NT5TU32M16 - UART console J2, populated - USB 2.0 port direct to SOC - 6 GPIO LEDs power, 2G, 5G, wps2g, wps5g, line - 3 buttons reset, wps, "reg" (registeration) - 4 antennas internal omni-directional plates NOT YET SUPPORTED: VoIP - Si3050-FT + Si3019-FT Voice DAA, SPI control, PCM data - Phone Ports "TEL", "LINE" RJ11, 4P2C (2 pins) **MAC addresses:** MAC address labeled as MAC ADDRESS MACs present in both wifi cal data and uboot environment eth0.1/phy1 ---- *:82 rf 0x4 phy0 ---- *:83 factory 0x4 eth0.2 MAC *:b8 "wanaddr" **Installation:** Method 1: Firmware upgrade page: (if you cannot access the APs webpage) factory reset with the reset button connect ethernet to a computer OEM webpage at 192.168.0.1 username and password 'admin' Navigate to gear icon, "Device Management", "Tools" select the factory.dlf image Upload and verify checksum Method 2: Serial to upload initramfs: Follow directions for TFTP recovery upload and boot initramfs and do a sysupgrade **TFTP recovery:** Requires UART serial console, reset button does nothing rename initramfs-kernel.bin to 'uImageEPG600' make available on TFTP server at 192.168.99.8 power board, interrupt boot with "4" execute `tftpboot` and `bootm` (with the load address) **Return to OEM:** Images from OEM are provided, but not compatible with openwrt sysupgrade. So it must be modified. Alternatively, back up all mtd partitions before flashing **Note on switch registers:** The necessary registers needed for the QCA8337 switch can be read from interrupted boot (tftpboot, bootm) by using the following lines in the switch driver ar8327.c in the function 'ar8327_hw_config_of' where 'qca,ar8327-initvals' is parsed from DTS before the new register values are written: pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE)); pr_info("0x08 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD5_MODE)); pr_info("0x0c %08x\n", ar8xxx_read(priv, AR8327_REG_PAD6_MODE)); pr_info("0x10 %08x\n", ar8xxx_read(priv, AR8327_REG_POWER_ON_STRAP)); Signed-off-by: Michael Pratt

uboot-envtools: add support for APRESIA ApresiaLightGS120GT-SS

2023-02-13T11:22:17Z

This patch adds support for APRESIA ApresiaLightGS120GT-SS to uboot-envtools. Signed-off-by: INAGAKI Hiroshi

ramips: add support for ASUS RT-AX54

2023-02-12T17:27:45Z

Specifications: - Device: ASUS RT-AX54 (AX1800S/HP,AX54HP) - SoC: MT7621AT - Flash: 128MB - RAM: 256MB - Switch: 1 WAN, 4 LAN (10/100/1000 Mbps) - WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G - LEDs: 1x POWER (blue, configurable) 1x LAN (blue, configurable) 1x WAN (blue, configurable) 1x 2.4G (blue, not configurable) 1x 5G (blue, not configurable) Flash by U-Boot TFTP method: - Configure your PC with IP 192.168.1.2 - Set up TFTP server and put the factory.bin image on your PC - Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key Select "2. Upgrade firmware" Press enter when show "Run firmware after upgrading? (Y/n):" Select 0 for TFTP method Input U-Boot's IP address: 192.168.1.1 Input TFTP server's IP address: 192.168.1.2 Input IP netmask: 255.255.255.0 Input file name: openwrt-ramips-mt7621-asus_rt-ax1800hp-squashfs-factory.bin - Restart AP aftre see the log "Firmware upgrade completed!" Signed-off-by: Karl Chan

uboot-envtools: filogic: bpi-r3: fix env selection

2023-01-29T03:43:58Z

Selecting the environment when booting from SD card has been broken by a previous commit. Fix it. Fixes: f46355b4d7 ("uboot-envtools: mediatek_filogic: fix BPi-R3 when no OS is installed") Signed-off-by: Daniel Golle