staging/pepe2k/target/linux, branch v22.03.5

ramips: reduce Archer AX23 / MR70X SPI-frequency

2023-04-27T20:28:15Z

It was brought to attention the Archer AX23 v1 fails to read jffs2 data from time to time. While this is not reproducible on my unit, it is on others. Reducing the SPI frequency does the trick. While it worked with at lest 40 MHz, opt for the cautious side and choose a save frequency of 25 MHz. Apply the same treatment to the Mercusys MR70X which uses a similar design just in case. Signed-off-by: David Bauer (cherry picked from commit 2c530fcb972c112e7a2b10f9c21ac6d276624b5e)

ramips: fix lzma-loader for buffalo_WSR_600DHP

2023-04-23T12:15:54Z

This fixes a well known "LZMA ERROR 1" error, reported previously on numerous of similar devices. Fixes: #11919 Signed-off-by: Haoan Li (cherry picked from commit c7b484f3647c58da2f86395228a9927290a6f6ed)

ath79: create Aruba AP-105 APBoot compatible image

2023-04-18T10:08:45Z

Alter the Aruba AP-105 image generation process so OpenWrt can be loaded with the vendor Aruba APBoot. This works by prepending the OpenWrt LZMA loader to the uImage and jumping directly to the loader. Aruba does not offer bootm on these boards. This approach keeps compatibility to devices which had their U-Boot replaced. Both bootloaders can boot the same image. The same modification is most likely also possible for the Aruba AP-175. With this patch, new installations do not require replacing the bootloader and can be performed from the serial console without opening the case. Installation ------------ 1. Attach to the serial console of the AP-105. Interrupt autoboot and change the U-Boot env. $ setenv apb_rb_openwrt "setenv ipaddr 192.168.1.1; setenv serverip 192.168.1.66; netget 0x84000000 ap105.bin; go 0x84000040" $ setenv apb_fb_openwrt "cp.b 0xbf040000 0x84000000 0x10000; go 0x84000040" $ setenv bootcmd "run apb_fb_openwrt" $ saveenv 2. Load the OpenWrt initramfs image on the device using TFTP. Place the initramfs image as "ap105.bin" in the TFTP server root directory, connect it to the AP and make the server reachable at 192.168.1.66/24. $ run apb_rb_openwrt 3. Once OpenWrt booted, transfer the sysupgrade image to the device using scp and use sysupgrade to install the firmware. Signed-off-by: David Bauer (cherry picked from commit e11d00d44c66b1534fbc399fda55951cd0a2168a)

kernel: backport fix for recently introduced UBI bug

2023-04-15T02:32:41Z

Import commit "ubi: Fix failure attaching when vid_hdr offset equals to (sub)page size" which did not yet make it to stable upstream Linux trees. Fixes: #12232 Fixes: #12339 Signed-off-by: Daniel Golle (cherry picked from commit aad34818b50029e07ed9221ae46f9770d6e29785)

ramips: define remapping-range for DAP-X1860

2023-04-08T16:10:34Z

Prevent the BBT translation layer from remapping the UBI used for storing rootfs. Explicitly define the number of blocks reserved for remapping. Signed-off-by: David Bauer (cherry picked from commit 076da59f17803e9412ef5e50988aff6c7e536292)

ramips: add support for D-Link DAP-X1860 A1

2023-04-08T16:10:33Z

The DAP-X1860 is a wall-plug AX1800 repeater. Specifications: - MT7621, 256 MiB RAM, 128 MiB SPI NAND - MT7915 + MT7975 2x2 802.11ax (DBDC) - Ethernet: 1 port 10/100/1000 - LED RSSI bargraph (2x green, 1x red/orange), status and RSSI LEDs are incorrectly populated red/orange (should be red/green according to documentation) Installation: - Keep reset button pressed during plug-in - Web Recovery Updater is at 192.168.0.50 - Upload factory.bin, confirm flashing (seems to work best with Chromium-based browsers) Revert to OEM firmware: - tar -xvf DAP-X1860_RevA_Firmware_101b94.bin - openssl enc -d -md md5 -aes-256-cbc -in FWImage.st2 \ -out FWImage.st1 -k MB0dBx62oXJXDvt12lETWQ== - tar -xvf FWImage.st1 - flash kernel_DAP-X1860.bin via Recovery Signed-off-by: Sebastian Schaper (cherry picked from commit 3c31f6b521bb5fc49e222a8f2bcd454b73452a0e)

ramips: lower re305-v3 spi-max-frequency

2023-04-08T12:56:28Z

Fix flash I/O instability observed in newer devices with cFeon QH64A-104HIP (detected as en25qh64). Ref: https://forum.openwrt.org/t/support-for-tp-link-re305-v3/75893/91 Reported-by: Dimitri Souza Tested-by: Dimitri Souza Signed-off-by: Joe Mullally [alter commit-message - target master] Signed-off-by: David Bauer (cherry picked from commit 2122c80b321d439cf8b669ae26fcfeec605cf2cc)

lantiq: fix lzma-loader for Netgear DGN 3500(B)

2023-04-02T21:01:44Z

Fixes Uncompressing Kernel Image ... ERROR: LzmaDecode.c, 561 Fixes: #11701 for both 3500(B) Signed-off-by: Maik Goette (cherry picked from commit 4d9c38d654fdfb72ef641573bbf5b0f73f638f2e)

ath79: tiny: Do not build TPLink WPA8630Pv2 by default

2023-04-02T20:25:49Z

22.03.1+ and snapshot builds no longer fit the 6M flash space available for these models. This disables failing buildbot image builds for these devices. Images can still be built manually with ImageBuilder. Signed-off-by: Joe Mullally (cherry picked from commit 4965cbd259bb9001e8724f53520f4be1e4723212)

ramips: mt7621: mikrotik 760igs (hEX S) fix SFP

2023-04-02T20:25:49Z

This device uses an AR8031/AR8033 chip to convert SoC gmac1 RGMII to 1000base-x or sgmii for the SFP fibre cage. The SFP cage requires phy-mode rgmii-rxid, and without it will not recieve any packets: ethtool -S sfp rx_fcs_errors will increase when packets should be being received, but no other _rx counters will change. Fixes: c77858aa792 ("ramips: mt7621-dts: change phy-mode of gmac1 to rgmii") Reviewed-by: Robert Marko Reviewed-by: Arınç ÜNAL Signed-off-by: John Thomson (cherry picked from commit 7ea965b57803ceec20222279377e611652ac217f)