staging/xback/scripts, branch v18.06.0-rc1

env: only use color diffs on terminals

2018-05-05T07:44:43Z

When sending script/env diff's output to a file or pipeline, you don't want escape characters for ANSI color sequences fouling the byte stream. Signed-off-by: Philip Prindeville

download.pl: Change OpenWrt mirrors to HTTPS.

2018-05-01T09:12:15Z

These have supported HTTPS for quite a while. I have not seen any obvious breakage. Signed-off-by: Rosen Penev

download.pl: Change SourceForge address to HTTPS.

2018-05-01T09:12:15Z

SourceForge has supported HTTPS for its downloads for a long time now. I have not been able to see any failures resulting from this change. Signed-off-by: Rosen Penev

scripts/feeds: add support for git feeds with submodules

2018-04-27T13:19:19Z

Signed-off-by: Felix Fietkau

scripts: bundle-libraries: fix build on OS X (FS#1493)

2018-04-26T14:06:55Z

This allegedly fixes compilation of the library bundler preload library on Apple OS X. The resulting executables have not been runtime tested due to a lack of suitable test hardware. Signed-off-by: Jo-Philipp Wich

ipq40xx: add support for OpenMesh A62

2018-04-23T20:07:22Z

* QCA IPQ4019 * 256 MB of RAM * 32 MB of SPI NOR flash (s25fl256s1) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62 * 2T2R 5 GHz (channel 36-64) - QCA9888 hw2.0 (PCI) - requires special BDF in QCA9888/hw2.0/board-2.bin bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62 * 2T2R 5 GHz (channel 100-165) - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62 * multi-color LED (controlled via red/green/blue GPIOs) * 1x button (reset; kmod-input-gpio-keys compatible) * external watchdog - triggered GPIO * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio3: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + 802.3at POE+ - phy@mdio4: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 18-24V passive POE (mode B) * powered only via POE The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. The initramfs image can be started using setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)' tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb set fdt_high 0x85000000 bootm 0x84000000 Signed-off-by: Sven Eckelmann

scripts: add EVA ramboot script

2018-03-18T21:22:38Z

Use the EVA bootloader to load a small linux system into the ram and boot it from there: ./scripts/flashing/eva_ramboot.py 192.168.178.1 path/to/initramfs-kernel.bin Signed-off-by: Valentin Spreckels Acked-by: John Crispin [reworded commit message] Signed-off-by: Mathias Kresin

build: Allow to change the FIT config section name

2018-03-17T07:09:04Z

Some devices only boot when a special config is found in the image and completely ignore the default entry during the selection. These devices can now use the variable DEVICE_DTS_CONFIG in their device image definition. Signed-off-by: Sven Eckelmann

scripts/metadata.pm: allow group-only Require-User specs

2018-02-26T06:19:46Z

/lib/functions.sh can deal with Require-User specifications that only contain a group, but no user. Adjust metadata.pm to allow such specifications as well. Signed-off-by: Matthias Schiffer

build: cleanup leftover qconf files

2018-02-13T10:35:35Z

``make xconfig`` toplevel target will invoke ``make qconf`` inside ./scripts/config directory, which results a ``qconf`` executable. This commit removes leftover ``qconf`` executable during ``make config-clean``. Signed-off-by: Alif M. Ahmad