bcm63xx/u-boot/board/mscc, branch masterBroadcom-s U-Boothttps://git.openwrt.org/project/bcm63xx/u-boot/atom?h=master2019-05-03T14:46:36Zboard: mscc: luton: Update MSCC Luton board2019-05-03T14:46:36ZHoratiu Vultur2019-05-01T11:16:59Zurn:sha1:bd9216e29b81ff2e35d203668f319aaaf396e018
Implement method board_phy_config to configure the external phys
on the pcb90.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
board: mscc: ocelot: Update MSCC Ocelot board.2019-05-03T14:42:23ZHoratiu Vultur2019-04-24T09:27:58Zurn:sha1:06d270cf57a48abbb71daa2ea30178ab04dc9cef
Implement method board_phy_config to configure the phy for pcb120.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
board: mscc: serval: Update MSCC Serval boards2019-05-03T14:42:23ZHoratiu Vultur2019-04-11T12:11:33Zurn:sha1:d2691b4af2cd2c3cb7f385938fcd63af7de74fca
In Serval SoC family there are 2 different pcb, both of them have the same
phy, but with different version. Therefore implement board_phy_config
and set all the phys in the same way.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
board: mscc: serval: Fix board detect2019-05-03T14:42:23ZHoratiu Vultur2019-04-15T09:56:37Zurn:sha1:c6b2e7117db83e9aaba5d47b56c5d918ce92fcf0
When detecting the board, it was reading a register in the GPIO page of
the phy and based on that value it was making a decision. The bug was that
after the GPIO page for the first phy was set it was not reseted back.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
board: mscc: jr2: Update MSCC Jaguar2 boards2019-04-12T15:32:51ZHoratiu Vultur2019-04-03T17:54:46Zurn:sha1:6aa50ae22c63e2b509bad2a815c12946b8a9aaf8
In Jaguar2 SoC family there are 3 different pcb. Each of this needs
to configure the phys in different ways. Therefore implement the
function board_phy_config and based on pcb configure them accordingly.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
MSCC: Fix Jaguar2 board detection.2019-02-01T13:09:31ZHoratiu Vultur2019-01-29T09:58:34Zurn:sha1:78b543141090b7c35a64418157b5194588a9f955
When power cycle the Jaguar2 boards, it couldn't read the
phys, therefore it always deduce that the board type is
pcb111.
Add a small delay after setting the gpio pins, fix the
issue.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
MSCC: Jaguar2 enable debug uart2019-02-01T13:08:54ZHoratiu Vultur2019-01-29T09:50:16Zurn:sha1:45988b123cf40bb651d7c48e913b010a8e255643
Enable debug uart for Jaguar2 SoC family.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
MSCC: Add board support for Serval SoC family.2019-01-23T17:28:09ZHoratiu Vultur2019-01-23T15:39:45Zurn:sha1:a834cb817fb1a11607ea8e6394235843be079fdd
Add board support and configuration for Jaguar2 SoC family.
The detection of the board type is based on the phy ids.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
MSCC: Add board support for Servalt SoC family2019-01-23T17:27:26ZHoratiu Vultur2019-01-17T14:33:28Zurn:sha1:036d95958bdb7555e61ccb7f9654319fee612e51
Add board support, configuration and DTS for Servalt SoC
family. Currently there is one board in this family.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
MIPS: mscc: ocelot: add switch reset support2019-01-23T17:26:44ZGregory CLEMENT2019-01-17T16:07:14Zurn:sha1:2f8d0677366d859bd2f23fc58280e913f15a4f61
On some ocelots platform a workaround is needed in order to be able to
reset the switch without resetting the DDR.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>