Broadcom-s U-Boot https://git.openwrt.org/project/bcm63xx/u-boot/atom?h=master 2019-04-30T01:41:40Z 2019-04-30T01:41:40Z Simon Goldschmidt 2018-09-30T12:31:53Z urn:sha1:f89d6133eef2e068f9c33853b6584d7fcbfa9d2e Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing values. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> [trini: Re-run migration] Signed-off-by: Tom Rini <trini@konsulko.com> 2019-04-30T01:41:40Z Tom Rini 2019-04-29T19:54:04Z urn:sha1:d168bcb6fe39108042c0c771f0823a95346a8e7e Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2019-02-22T15:17:41Z Tom Rini 2019-02-22T15:17:41Z urn:sha1:fca0128da48031286f0cb2414ee6c94e9162943c Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2018-11-14T00:44:53Z Tom Rini 2018-11-14T00:44:53Z urn:sha1:4114a2614b0b7e3f147e2903a8e1d498c4cfb4ba Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2018-08-17T17:04:00Z Adam Ford 2018-08-06T19:26:50Z urn:sha1:cc3fedb2046962c6a11e16b1d73d98b4e108a651 This converts the following to Kconfig: CONFIG_TWL4030_LED CONFIG_TWL4030_INPUT This also removes dead references to: CONFIG_TWL4030_KEYPAD Signed-off-by: Adam Ford <aford173@gmail.com> 2018-08-16T20:45:02Z Tom Rini 2018-08-16T12:16:24Z urn:sha1:86cf1c82850f7c226f23684e19616e526ffaf10f We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com> 2018-04-27T18:54:11Z Adam Ford 2018-04-15T17:51:26Z urn:sha1:f1b1f77060beadbfe9f42a3be00019bd025afbd6 This converts the following to Kconfig: CONFIG_SPI This partly involves updating code that assumes that CONFIG_SPI implies things that are specific to the MPC8xx SPI driver. For now, just update the CONFIG tests. This also involves reworking the default for CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a reasonable default, as it does not cause any compile failures. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> 2018-04-08T00:37:13Z Tom Rini 2018-04-08T00:27:54Z urn:sha1:c9542eae0bf815e8196dd9238c38290de173725a Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2018-03-16T14:28:52Z Tom Rini 2018-03-07T00:02:27Z urn:sha1:6f6b7cfa89e5aa3b643196a4ccc8b1ba5d6fa7a4 This converts the following to Kconfig: CONFIG_CONS_INDEX We have existing entries for this option in a number of places, with different guards on them. They're also sometimes used for things not directly inside of the serial driver. First, introduce a new symbol to guard the use of CONFIG_CONS_INDEX, so that in the case where we don't need this for the serial driver, but for some other use, we can still do it. Next, consolidate all of these into the single entry in drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that we can imply a correct value here to make the defconfig side of this smaller. Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rework a lot of the logic here, such that I took authorship from Adam, but kept his S-o-B line] Signed-off-by: Tom Rini <trini@konsulko.com> 2018-02-27T21:25:30Z Michal Simek 2018-02-26T15:01:02Z urn:sha1:3b3ea2c56ec4bc5588281fd103c744e608f8b25c Enable networking command only when NET is enabled. And remove selecting NET for CMD_NET Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Tom Rini <trini@konsulko.com>