bcm63xx/u-boot/configs/devkit8000_defconfig, branch master

configs: move CONFIG_SPL_TEXT_BASE to Kconfig

2019-04-30T01:41:40Z

Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing values. Signed-off-by: Simon Goldschmidt [trini: Re-run migration] Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2019-04-30T01:41:40Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2018-11-14T00:44:53Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

Convert CONFIG_TWL4030_LED et al to Kconfig

2018-08-17T17:04:00Z

This converts the following to Kconfig: CONFIG_TWL4030_LED CONFIG_TWL4030_INPUT This also removes dead references to: CONFIG_TWL4030_KEYPAD Signed-off-by: Adam Ford

configs: Migrate CONFIG_NR_DRAM_BANKS

2018-08-16T20:45:02Z

We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini

net: Add Kconfig option for BOOTP_NTPSERVER

2018-05-15T01:28:38Z

Add a Kconfig option for BOOTP_NTPSERVER to enable the DHCP/BOOTP option to configure the sntp server address. Signed-off-by: Chris Packham Acked-by: Joe Hershberger

configs: Resync with savedefconfig

2018-04-08T00:37:13Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

Convert all of CONFIG_CONS_INDEX to Kconfig

2018-03-16T14:28:52Z

This converts the following to Kconfig: CONFIG_CONS_INDEX We have existing entries for this option in a number of places, with different guards on them. They're also sometimes used for things not directly inside of the serial driver. First, introduce a new symbol to guard the use of CONFIG_CONS_INDEX, so that in the case where we don't need this for the serial driver, but for some other use, we can still do it. Next, consolidate all of these into the single entry in drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that we can imply a correct value here to make the defconfig side of this smaller. Signed-off-by: Adam Ford [trini: Rework a lot of the logic here, such that I took authorship from Adam, but kept his S-o-B line] Signed-off-by: Tom Rini

configs: Re-sync with CONFIG_DISTRO_DEFAULTS

2018-02-23T15:21:41Z

A number of platforms include config_distro_defaults.h but do not enable CONFIG_DISTRO_DEFAULTS. As they plainly intended to, set that flag and re-sync config files. Signed-off-by: Tom Rini

cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGA

2018-02-06T01:58:11Z

cmd/Makefile has: ifdef CONFIG_FPGA obj-$(CONFIG_CMD_FPGA) += fpga.o endif which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently does nothing. Let's remove that Makefile conditional and instead express this equivalent dependency in Kconfig, so a lot of redundant # CONFIG_CMD_FPGA is not set can be removed from board defconfigs that don't actually have an FPGA. Signed-off-by: Tuomas Tynkkynen