bcm63xx/u-boot/configs/draco_defconfig, branch master

configs: Resync with savedefconfig

2019-04-30T01:41:40Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

spl: Kconfig: Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT

2019-02-01T14:12:48Z

Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both SPL and U-Boot. Signed-off-by: Tien Fong Chee Reviewed-by: Simon Goldschmidt Reviewed-by: Tom Rini

configs: Migrate and re-enabled CONFIG_CMD_MTDPARTS

2018-11-14T15:53:27Z

Now that CMD_UBI does not select CMD_MTDPARTS we need to make platforms that had been enabling it turn it on by hand. This exposed that we had not yet migrated CMD_MTDPARTS fully, so do so now. Fixes: 86dfa556d927 ("cmd: ubi: Remove useless call to mtdparts_init()") Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2018-11-14T00:44:53Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2018-09-03T19:26:12Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

Migrate bootlimit to Kconfig

2018-08-17T17:03:59Z

Migrate boards which set bootlimit in the environment to Kconfig. We exclude gurnard_defconfig which includes a bootlimit=, but doesn't set CONFIG_BOOTCOUNT_LIMIT, so we'd fail to include a bootlimit setting if we migrated it. display5_defconfig and display5_factory_defconfig share a SYS_CONFIG_NAME, but only display5_defconfig enables CONFIG_BOOTCOUNT_LIMIT, so we fail to set bootlimit= in display5_factory_defconfig. This is okay because the display5_factory_defconfig doesn't need to have it set, as it is only meant to prepare the board in the factory. Environment changes for all modified configs as seen from buildman: boards.cfg is up to date. Nothing to do. Summary of 3 commits for 32 boards (8 threads, 1 job per thread) 01: Merge git://git.denx.de/u-boot-x86 arm: + draco etamin rastaban pxm2 display5 thuban rut 02: Add BOOTCOUNT_BOOTLIMIT to set reboot limit 03: Migrate bootlimit to Kconfig - display5_factory: bootlimit=3 Signed-off-by: Alex Kiernan Reviewed-by: Lukasz Majewski

configs: Migrate CONFIG_NR_DRAM_BANKS

2018-08-16T20:45:02Z

We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2018-06-04T15:57:37Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

Convert CONFIG_SPI to Kconfig

2018-04-27T18:54:11Z

This converts the following to Kconfig: CONFIG_SPI This partly involves updating code that assumes that CONFIG_SPI implies things that are specific to the MPC8xx SPI driver. For now, just update the CONFIG tests. This also involves reworking the default for CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a reasonable default, as it does not cause any compile failures. Signed-off-by: Adam Ford Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2018-04-17T14:10:47Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini