bcm63xx/u-boot/configs/mx7dsabresd_defconfig, branch master

Convert CONFIG_SUPPORT_EMMC_BOOT to Kconfig

2019-05-04T17:04:12Z

This converts the following to Kconfig: CONFIG_SUPPORT_EMMC_BOOT As requested by Michal Simek , these boards have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated: xilinx_zynqmp_zc1275_revB xilinx_zynqmp_zc1751_xm018_dc4 xilinx_zynqmp_zc1751_xm019_dc5 xilinx_zynqmp_zcu100_revC xilinx_zynqmp_zcu102_rev1_0 xilinx_zynqmp_zcu102_revA xilinx_zynqmp_zcu102_revB xilinx_zynqmp_zcu104_revA xilinx_zynqmp_zcu104_revC xilinx_zynqmp_zcu106_revA xilinx_zynqmp_zcu111_revA Signed-off-by: Alex Kiernan Acked-by: Lukasz Majewski Acked-by: Patrick Delaunay Acked-by: Ramon Fried Reviewed-by: Andy Shevchenko Tested-by: Sébastien Szymanski

configs: Resync with savedefconfig

2019-04-30T01:41:40Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

Kconfig: Migrate BOUNCE_BUFFER

2019-01-19T14:49:26Z

The bounce buffer is used by a few drivers (most of the MMC drivers) to overcome limitations in their respective DMA implementation. This moves the configuration to Kconfig and makes it user-selectable (even though it will be a required feature to make those drivers work): the expected usage is for drivers depending on this to 'select' it unconditionally from their respective Kconfig (see follow-up patches). This commit includes a full migration using moveconfig.py to ensure that each commit compiles. To ensure bisectability we update dependencies of various drivers to now select BOUNCE_BUFFER when needed. [trini: Squash all patches to ensure bisectability] Signed-off-by: Tom Rini Signed-off-by: Philipp Tomsich Reviewed-by: Otavio Salvador [dw_mmc portion] Reviewed-by: Fabio Estevam [mxsmmc portion] Reviewed-by: Simon Glass [tegra portion]

configs: Resync with savedefconfig

2018-09-03T19:26:12Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

Convert CONFIG_MII et al to Kconfig

2018-08-17T17:03:54Z

This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford Acked-by: Jagan Teki Acked-by: Joe Hershberger

configs: Migrate CONFIG_NR_DRAM_BANKS

2018-08-16T20:45:02Z

We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2018-08-08T01:40:14Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

Merge git://git.denx.de/u-boot-imx

2018-04-30T11:14:05Z

Convert CONFIG_SPI to Kconfig

2018-04-27T18:54:11Z

This converts the following to Kconfig: CONFIG_SPI This partly involves updating code that assumes that CONFIG_SPI implies things that are specific to the MPC8xx SPI driver. For now, just update the CONFIG tests. This also involves reworking the default for CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a reasonable default, as it does not cause any compile failures. Signed-off-by: Adam Ford Signed-off-by: Tom Rini

mx7dsabresd: Remove the mx7dsabresd_secure_defconfig target

2018-04-26T06:57:52Z

mx7dsabresd_secure_defconfig was introduced to allow booting NXP kernel that has CAAM support and needs to boot in secure mode. Instead of keeping two different config targets for the same board, remove mx7dsabresd_secure_defconfig and select CONFIG_ARMV7_BOOT_SEC_DEFAULT inside mx7dsabresd_defconfig so that this target could be used to boot both mainline and the vendor kernel. This makes maintenance task easier and avoid potentially confusion for the end user. Signed-off-by: Fabio Estevam Acked-by: Bryan O'Donoghue