bcm63xx/u-boot/configs/nokia_rx51_defconfig, branch master

Convert CONFIG_TWL4030_LED et al to Kconfig

2018-08-17T17:04:00Z

This converts the following to Kconfig: CONFIG_TWL4030_LED CONFIG_TWL4030_INPUT This also removes dead references to: CONFIG_TWL4030_KEYPAD Signed-off-by: Adam Ford

configs: Migrate CONFIG_NR_DRAM_BANKS

2018-08-16T20:45:02Z

We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini

Convert CONFIG_SPI to Kconfig

2018-04-27T18:54:11Z

This converts the following to Kconfig: CONFIG_SPI This partly involves updating code that assumes that CONFIG_SPI implies things that are specific to the MPC8xx SPI driver. For now, just update the CONFIG tests. This also involves reworking the default for CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a reasonable default, as it does not cause any compile failures. Signed-off-by: Adam Ford Signed-off-by: Tom Rini

Convert all of CONFIG_CONS_INDEX to Kconfig

2018-03-16T14:28:52Z

This converts the following to Kconfig: CONFIG_CONS_INDEX We have existing entries for this option in a number of places, with different guards on them. They're also sometimes used for things not directly inside of the serial driver. First, introduce a new symbol to guard the use of CONFIG_CONS_INDEX, so that in the case where we don't need this for the serial driver, but for some other use, we can still do it. Next, consolidate all of these into the single entry in drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that we can imply a correct value here to make the defconfig side of this smaller. Signed-off-by: Adam Ford [trini: Rework a lot of the logic here, such that I took authorship from Adam, but kept his S-o-B line] Signed-off-by: Tom Rini

Kconfig: cmd: Make networking command dependent on NET

2018-02-27T21:25:30Z

Enable networking command only when NET is enabled. And remove selecting NET for CMD_NET Signed-off-by: Michal Simek Signed-off-by: Tom Rini

cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGA

2018-02-06T01:58:11Z

cmd/Makefile has: ifdef CONFIG_FPGA obj-$(CONFIG_CMD_FPGA) += fpga.o endif which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently does nothing. Let's remove that Makefile conditional and instead express this equivalent dependency in Kconfig, so a lot of redundant # CONFIG_CMD_FPGA is not set can be removed from board defconfigs that don't actually have an FPGA. Signed-off-by: Tuomas Tynkkynen

Convert CONFIG_TWL4030_USB to Kconfig

2018-01-22T21:43:30Z

This converts the following to Kconfig: CONFIG_TWL4030_USB Signed-off-by: Adam Ford

Convert CONFIG_USB_MUSB_HCD et al to Kconfig

2018-01-22T21:43:29Z

This converts the following to Kconfig: CONFIG_USB_MUSB_HCD CONFIG_USB_MUSB_UDC CONFIG_USB_DAVINCI CONFIG_USB_OMAP3 CONFIG_USB_DA8XX CONFIG_USB_AM35X Signed-off-by: Adam Ford

configs: Resync with savedefconfig

2017-10-30T16:58:33Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

cmd: Toggle the default value of CONFIG_CMD_IMLS

2017-10-10T21:51:04Z

Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: Tuomas Tynkkynen