Broadcom-s U-Boot https://git.openwrt.org/project/bcm63xx/u-boot/atom?h=master 2019-04-30T01:41:40Z 2019-04-30T01:41:40Z Simon Goldschmidt 2018-09-30T12:31:53Z urn:sha1:f89d6133eef2e068f9c33853b6584d7fcbfa9d2e Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing values. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> [trini: Re-run migration] Signed-off-by: Tom Rini <trini@konsulko.com> 2019-04-30T01:41:40Z Tom Rini 2019-04-29T19:54:04Z urn:sha1:d168bcb6fe39108042c0c771f0823a95346a8e7e Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2019-04-10T10:04:32Z Paul Kocialkowski 2019-03-14T10:36:16Z urn:sha1:9d0f9e837421c3e6d1e99caed401511d886a1c36 Most of the boards we support with H3/H5 enable DRAM on-die termination, which is consistent with the high DRAM clocks that are used. Make it the default (like it's done for other similar platforms) instead of defining it in each defconfig. Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com> 2019-04-10T10:04:32Z Paul Kocialkowski 2019-03-14T10:36:15Z urn:sha1:882b71e47df2889c77105ddcfe34cbafa762a208 Most H3/H5 boards we support have the DRAM ZQ value set to 3881979, which is also consistent with the default set for the R40. Make this value the default on H3/H5 instead of 123. Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com> 2019-02-07T19:53:03Z Tom Rini 2019-02-07T19:53:03Z urn:sha1:7ae2729401bb9cd6bbe233c12a1d0a3404221659 Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2019-01-18T16:49:09Z Jagan Teki 2018-12-22T12:48:10Z urn:sha1:29d280c88a1ff331dce2d4c7a5aaf2402aa0fd8a Onc of key blocker for using USB Generic host controller drivers in Allwinner are CLK and RESET drivers, now these available for USB usage. So switch sunxi USB use EHCI and OHCI Generic controllers. Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD where it already have USB_EHCI_HCD Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> 2018-09-03T19:26:12Z Tom Rini 2018-09-03T19:26:12Z urn:sha1:8c5cad05c97122b33ef8de981b56f701d6bfb6ea Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2018-08-16T20:45:02Z Tom Rini 2018-08-16T12:16:24Z urn:sha1:86cf1c82850f7c226f23684e19616e526ffaf10f We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com> 2018-04-16T22:45:35Z Alexander Graf 2018-04-12T07:58:44Z urn:sha1:4f67b93fb7f558dbdd5f7a3e763ec19b6ec62460 We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot could load distro images that usually get shipped as iso images. These images usually come with a board agnostic boot environment. However, there is very little point in having ISO support enabled (for anyone really) in SPL, as the whole idea of SPL is to load U-Boot proper which again is board specific. So the fact that we enable ISO support in U-Boot proper does not mean at all that we want ISO support in U-Boot SPL. Hence, let's remove the Kconfig dependency. Along the way, let's also clean up all those default configs that disabled SPL ISO support. Signed-off-by: Alexander Graf <agraf@suse.de> 2018-04-08T00:37:13Z Tom Rini 2018-04-08T00:27:54Z urn:sha1:c9542eae0bf815e8196dd9238c38290de173725a Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>