Broadcom-s U-Boot https://git.openwrt.org/project/bcm63xx/u-boot/atom?h=master 2019-04-30T01:41:40Z 2019-04-30T01:41:40Z Simon Goldschmidt 2018-09-30T12:31:53Z urn:sha1:f89d6133eef2e068f9c33853b6584d7fcbfa9d2e Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing values. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> [trini: Re-run migration] Signed-off-by: Tom Rini <trini@konsulko.com> 2019-04-30T01:41:40Z Tom Rini 2019-04-29T19:54:04Z urn:sha1:d168bcb6fe39108042c0c771f0823a95346a8e7e Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2019-04-10T10:04:32Z Paul Kocialkowski 2019-03-14T10:36:16Z urn:sha1:9d0f9e837421c3e6d1e99caed401511d886a1c36 Most of the boards we support with H3/H5 enable DRAM on-die termination, which is consistent with the high DRAM clocks that are used. Make it the default (like it's done for other similar platforms) instead of defining it in each defconfig. Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com> 2019-02-22T15:17:41Z Tom Rini 2019-02-22T15:17:41Z urn:sha1:fca0128da48031286f0cb2414ee6c94e9162943c Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2019-02-11T07:33:07Z Hauke Mehrtens 2019-01-13T16:41:47Z urn:sha1:9b83787c0c3e814638ffcb2199b8ac17cea74e36 The Detection pin is at PF6 and not at PH13 like defined before. I checked the schematics and now I am am not seeing this error message any more: Loading Environment from FAT... Card did not respond to voltage select! CONFIG_MMC_SUNXI_SLOT_EXTRA is also not needed because the second MCC slot is for the Wifi card. Fixes: 76d69eb01de ("sun50i: h5: Add initial Orange Pi Zero Plus support") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Reviewed-by: Jagan Teki <jagan@openedev.com> 2019-02-07T19:53:03Z Tom Rini 2019-02-07T19:53:03Z urn:sha1:7ae2729401bb9cd6bbe233c12a1d0a3404221659 Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2019-01-18T16:49:09Z Jagan Teki 2018-12-22T12:48:10Z urn:sha1:29d280c88a1ff331dce2d4c7a5aaf2402aa0fd8a Onc of key blocker for using USB Generic host controller drivers in Allwinner are CLK and RESET drivers, now these available for USB usage. So switch sunxi USB use EHCI and OHCI Generic controllers. Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD where it already have USB_EHCI_HCD Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> 2018-09-03T19:26:12Z Tom Rini 2018-09-03T19:26:12Z urn:sha1:8c5cad05c97122b33ef8de981b56f701d6bfb6ea Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com> 2018-08-16T20:45:02Z Tom Rini 2018-08-16T12:16:24Z urn:sha1:86cf1c82850f7c226f23684e19616e526ffaf10f We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com> 2018-06-16T09:22:42Z Hauke Mehrtens 2018-06-09T16:34:46Z urn:sha1:76d69eb01dee492f5ecf43c43d7301fec6c5b99f Orange Pi Zero Plus is an open-source single-board computer using the Allwinner H5 SOC. H5 Orangepi Zero Plus has - Quad-core Cortex-A53 - 512MB DDR3 - micrSD slot - 16MBit SPI Nor flash - Debug TTL UART - 1GBit/s Ethernet (RTL8211E) - Wifi (RTL8189FTV) - USB 2.0 Host - USB 2.0 OTG + power supply The device tree file is copied from the Linux kernel 4.17. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>