bcm63xx/u-boot/configs/spear600_defconfig, branch master

configs: Resync with savedefconfig

2019-04-30T01:41:40Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

configs: Migrate and re-enabled CONFIG_CMD_MTDPARTS

2018-11-14T15:53:27Z

Now that CMD_UBI does not select CMD_MTDPARTS we need to make platforms that had been enabling it turn it on by hand. This exposed that we had not yet migrated CMD_MTDPARTS fully, so do so now. Fixes: 86dfa556d927 ("cmd: ubi: Remove useless call to mtdparts_init()") Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2018-11-14T00:44:53Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

Convert CONFIG_MISC_INIT_R to Kconfig

2018-08-17T17:04:00Z

This converts the following to Kconfig: CONFIG_MISC_INIT_R Signed-off-by: Adam Ford [trini: Update the defaults logic slightly] Signed-off-by: Tom Rini

Convert CONFIG_MII et al to Kconfig

2018-08-17T17:03:54Z

This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford Acked-by: Jagan Teki Acked-by: Joe Hershberger

configs: Migrate CONFIG_NR_DRAM_BANKS

2018-08-16T20:45:02Z

We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini

Convert CONFIG_MTD_PARTITIONS et al to Kconfig

2018-07-22T23:20:17Z

This converts the following to Kconfig: CONFIG_MTD_PARTITIONS CONFIG_MTD_DEVICE Signed-off-by: Adam Ford

Convert all of CONFIG_CONS_INDEX to Kconfig

2018-03-16T14:28:52Z

This converts the following to Kconfig: CONFIG_CONS_INDEX We have existing entries for this option in a number of places, with different guards on them. They're also sometimes used for things not directly inside of the serial driver. First, introduce a new symbol to guard the use of CONFIG_CONS_INDEX, so that in the case where we don't need this for the serial driver, but for some other use, we can still do it. Next, consolidate all of these into the single entry in drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that we can imply a correct value here to make the defconfig side of this smaller. Signed-off-by: Adam Ford [trini: Rework a lot of the logic here, such that I took authorship from Adam, but kept his S-o-B line] Signed-off-by: Tom Rini

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

2018-02-24T02:41:49Z

This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: Adam Ford [trini: Re-run the migration] Signed-off-by: Tom Rini

configs: Migrate CONFIG_SYS_TEXT_BASE

2018-02-11T14:30:09Z

On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini