bcm63xx/u-boot/configs/vinco_defconfig, branch master

Convert CONFIG_SUPPORT_EMMC_BOOT to Kconfig

2019-05-04T17:04:12Z

This converts the following to Kconfig: CONFIG_SUPPORT_EMMC_BOOT As requested by Michal Simek , these boards have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated: xilinx_zynqmp_zc1275_revB xilinx_zynqmp_zc1751_xm018_dc4 xilinx_zynqmp_zc1751_xm019_dc5 xilinx_zynqmp_zcu100_revC xilinx_zynqmp_zcu102_rev1_0 xilinx_zynqmp_zcu102_revA xilinx_zynqmp_zcu102_revB xilinx_zynqmp_zcu104_revA xilinx_zynqmp_zcu104_revC xilinx_zynqmp_zcu106_revA xilinx_zynqmp_zcu111_revA Signed-off-by: Alex Kiernan Acked-by: Lukasz Majewski Acked-by: Patrick Delaunay Acked-by: Ramon Fried Reviewed-by: Andy Shevchenko Tested-by: Sébastien Szymanski

configs: Resync with savedefconfig

2019-04-30T01:41:40Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

Convert CONFIG_SF_DEFAULT_* to Kconfig

2019-03-25T21:36:53Z

This converts the following to Kconfig: CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_MODE CONFIG_SF_DEFAULT_SPEED I use moveconfig script and then manual check on generated u-boot.cfg to solve the remaining issue. Signed-off-by: Patrick Delaunay

configs: Resync with savedefconfig

2018-09-03T19:26:12Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

configs: Migrate CONFIG_NR_DRAM_BANKS

2018-08-16T20:45:02Z

We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2018-04-17T14:10:47Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

at91: vinco: Add FDT support

2018-04-06T20:11:09Z

Sync DTS from Linux and add FDT support for AT91 vinco board. usb0, usb1, and usb2 nodes removed, since there is no support it. Cc: Gregory CLEMENT Signed-off-by: Jagan Teki

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

2018-02-24T02:41:49Z

This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: Adam Ford [trini: Re-run the migration] Signed-off-by: Tom Rini

configs: Migrate CONFIG_SYS_TEXT_BASE

2018-02-11T14:30:09Z

On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini

cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGA

2018-02-06T01:58:11Z

cmd/Makefile has: ifdef CONFIG_FPGA obj-$(CONFIG_CMD_FPGA) += fpga.o endif which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently does nothing. Let's remove that Makefile conditional and instead express this equivalent dependency in Kconfig, so a lot of redundant # CONFIG_CMD_FPGA is not set can be removed from board defconfigs that don't actually have an FPGA. Signed-off-by: Tuomas Tynkkynen