bcm63xx/u-boot/drivers/pinctrl/meson, branch master

pinctrl: meson-gxbb: add hdmi related pins

2019-06-12T09:50:02Z

The GXBB pinctrl is missing pins related to HDMI, namely hot plug detection (hpd) and I2C (sda + scl). This fixes HDMI support for GXBB in u-boot. Reported-by: Mohammad Rasim Signed-off-by: Maxime Jourdan Acked-by: Neil Armstrong Tested-by: Mohammad Rasim Signed-off-by: Neil Armstrong

pinctrl: meson: g12a: add DS bank value

2019-06-12T09:50:02Z

add drive-strength bank regiter and bit value for G12A SoC Signed-off-by: Guillaume La Roque Tested-by: Neil Armstrong Signed-off-by: Neil Armstrong

pinctrl: meson: add support of drive-strength-microamp

2019-06-12T09:50:02Z

drive-strength-microamp is a new feature needed for G12A SoC. the default DS setting after boot is usually 500uA and it is not enough for many functions. We need to be able to set the drive strength to reliably enable things like MMC, I2C, etc ... Signed-off-by: Guillaume La Roque Tested-by: Neil Armstrong Signed-off-by: Neil Armstrong

pinctrl: meson-axg: add support for getting pinmux status

2019-06-12T09:50:02Z

In order to support the "pinmux status" command, use the common functions to get the pins count and names, and add the AXG specific function to get the current function from registers. Signed-off-by: Neil Armstrong

pinctrl: meson-gx: add support for getting pinmux status

2019-06-12T09:50:02Z

In order to support the "pinmux status" command, use the common functions to get the pins count and names, and add the GX specific function to get the current function from registers. Signed-off-by: Neil Armstrong Tested-by: Maxime Jourdan

pinctrl: meson: add common function to get pins name

2019-06-12T09:50:02Z

In order to support the "pinmux status" command, add common function to get pins count and pin name. Signed-off-by: Neil Armstrong

pinctrl: meson-gx: fix GPIO_TEST_N and GPIOCLK_ groups

2019-06-12T09:50:02Z

The GPIO_TEST_N was in the wrong pmx group table, move it back with the AO groups, GPIODV_18 was missing, add it back, and finally the GPIOCLK_* group names were missing. Signed-off-by: Neil Armstrong

pinctrl: meson: add g12a support

2019-04-23T09:19:09Z

Add pinctrl support for the Amlogic G12A SoC, which is very similar to the Amlogic AXG support but with an additionnal drive-strength register bank. Signed-off-by: Jerome Brunet Signed-off-by: Neil Armstrong

pinctrl: meson: axg: Fix PIN and BANK offsets

2019-04-10T14:54:59Z

Periphs bank offset must be applied on all pins and PMX bank to prevent issue in meson_pinconf_set call. Without offset on pins when a call to pinconf is done meson_gpio_calc_reg_and_bit return wrong offset. To avoid breaking pmx function offset is needed in pmx bank structure too. Signed-off-by: Guillaume La Roque Signed-off-by: Neil Armstrong

pinctrl: meson: add pinconf support

2019-01-29T10:19:15Z

Adding pinconf support is necessary to enable boot from SPI without breaking the eMMC. When booting from SPI, the ROM code leave pull downs on the eMMC pad. We need to set pinconf provided in DT to solve this Signed-off-by: Jerome Brunet Signed-off-by: Neil Armstrong [narmstrong: added missing comma in pinctrl-meson-axg-pmx.c]