bcm63xx/u-boot/include/configs/ls1088a_common.h, branch master

configs: move CONFIG_SPL_TEXT_BASE to Kconfig

2019-04-30T01:41:40Z

Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing values. Signed-off-by: Simon Goldschmidt [trini: Re-run migration] Signed-off-by: Tom Rini

mc : Reduce MC memory size to 128M

2019-03-15T06:22:00Z

ls2088, ls1088 : minimum MC Memory size is 128 MB lx2 : minimum MC memory size is 256 MB Signed-off-by: Meenakshi Aggarwal Acked-by: Joe Hershberger Reviewed-by: Prabhakar Kushwaha

configs: fsl: move DDR specific defines to Kconfig

2019-03-03T15:26:01Z

Moves below DDR specific defines to Kconfig: CONFIG_FSL_DDR_BIST CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE CONFIG_FSL_DDR_INTERACTIVE CONFIG_FSL_DDR_SYNC_REFRESH Signed-off-by: Rajesh Bhagat Reviewed-by: York Sun Reviewed-by: Prabhakar Kushwaha

armv8: layerscape: move CONFIG_LAYERSCAPE to Kconfig

2019-02-19T04:56:44Z

Moves CONFIG_LAYERSCAPE for all NXP Layerscape platforms. Signed-off-by: Rajesh Bhagat Reviewed-by: Prabhakar Kushwaha

armv8: ls1088ardb: Add TFABOOT support

2019-01-17T21:16:04Z

TFABOOT support includes: - ls1088ardb_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - MC address changes for TFABOOT - define BOOTCOMMAND for TFABOOT - ifc chip select changes for TFABOOT Signed-off-by: Rajesh Bhagat Signed-off-by: Pankit Garg Reviewed-by: York Sun

armv8: ls1088ardb_pb: Add support for board detection

2018-12-06T22:37:19Z

ls1088ardb-pb and ls1088ardb both boards are ls1088a based soc, board type detection is dynamic at boot time Signed-off-by: Pramod Kumar Reviewed-by: York Sun

armv8: layerscape: Build u-boot-with-spl.bin for selected boards

2018-08-23T15:17:35Z

This patch reverts the changes made for ls1088a and ls2080a based boards in commit 18b6dd6cb0564 ("armv8: layerscape: Drop u-boot-with-spl.bin for selected boards"). u-boot-with-spl.bin is required for Gen3 based SoC where internal ROM copy data in the internal memory CC: Prabhakar Kushwaha CC: Priyanka Jain CC: Pramod Kumar CC: Ashish Kumar CC: York Sun Signed-off-by: Jagdish Gediya Reviewed-by: Prabhakar Kushwaha Reviewed-by: York Sun

configs: Migrate CONFIG_NR_DRAM_BANKS

2018-08-16T20:45:02Z

We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini

armv8: layerscape: Drop u-boot-with-spl.bin for selected boards

2018-07-26T17:59:35Z

For SPL boot with PBL, u-boot-with-spl-pbl.bin is the final image. Drop unused u-boot-with-spl.bin. Signed-off-by: York Sun CC: Mingkai Hu CC: Ruchika Gupta CC: Prabhakar Kushwaha CC: Udit Agarwal CC: Sumit Garg CC: Priyanka Jain

armv8: ls1088a: change dpl load command from apply to lazyapply

2018-07-26T17:59:35Z

use "fsl_mc lazyapply dpl addr" instead of "fsl_mc apply dpl addr" change dpl load addr to 0x80001000 from 0x80200000 because dpl gets corrupted at 0x80200000 during bootm command excecution. Signed-off-by: Jagdish Gediya Reviewed-by: York Sun