target/linux/ath79/dts/ar9331_teltonika_rut230-v1.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include "ar9331.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         model = "Teltonika RUT230 v1";
  10         compatible = "teltonika,rut230-v1", "qca,ar9331";
  11
  12         aliases {
  13                 label-mac-device = &eth1;
  14                 led-boot = &led_ss0;
  15                 led-failsafe = &led_ss0;
  16                 led-upgrade = &led_ss0;
  17         };
  18
  19         keys {
  20                 compatible = "gpio-keys";
  21
  22                 reset {
  23                         label = "reset";
  24                         linux,code = <KEY_RESTART>;
  25                         gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
  26                         debounce-interval = <60>;
  27                 };
  28
  29                 input {
  30                         label = "input";
  31                         linux,code = <BTN_0>;
  32                         gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
  33                         debounce-interval = <60>;
  34                 };
  35
  36                 sim-tray {
  37                         label = "sim-tray";
  38                         linux,code = <BTN_1>;
  39                         gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
  40                         debounce-interval = <60>;
  41                 };
  42         };
  43
  44         leds {
  45                 compatible = "gpio-leds";
  46                 pinctrl-names = "default";
  47                 pinctrl-0 = <&switch_led_disable_pins>;
  48
  49                 led_ss0: signal-strength-0 {
  50                         label = "green:signal-strength-0";
  51                         gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
  52                 };
  53
  54                 signal-strength-1 {
  55                         label = "green:signal-strength-1";
  56                         gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
  57                 };
  58
  59                 signal-strength-2 {
  60                         label = "green:signal-strength-2";
  61                         gpios = <&gpio 6 GPIO_ACTIVE_HIGH>;
  62                 };
  63
  64                 signal-strength-3 {
  65                         label = "green:signal-strength-3";
  66                         gpios = <&gpio 26 GPIO_ACTIVE_HIGH>;
  67                 };
  68
  69                 signal-strength-4 {
  70                         label = "green:signal-strength4";
  71                         gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
  72                 };
  73
  74                 2g {
  75                         label = "green:2g";
  76                         gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
  77                 };
  78
  79                 3g {
  80                         label = "green:3g";
  81                         gpios = <&gpio 24 GPIO_ACTIVE_HIGH>;
  82                 };
  83
  84                 lan {
  85                         label = "green:lan";
  86                         gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
  87                         /* GPIO 13 - ACTIVE HIGH for hwrev 0 */
  88                 };
  89
  90                 wan {
  91                         label = "green:wan";
  92                         gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
  93                         /* GPIO 14 - ACTIVE HIGH for hwrev 0 */
  94                 };
  95
  96                 /* 4G LED - GPIO21 ACTIVE_HIGH for RUT240 */
  97         };
  98
  99         reg_usb_vbus: reg_usb_vbus {
 100                 compatible = "regulator-fixed";
 101                 regulator-name = "usb_vbus";
 102                 regulator-min-microvolt = <5000000>;
 103                 regulator-max-microvolt = <5000000>;
 104                 gpio = <&gpio 19 GPIO_ACTIVE_HIGH>;
 105                 enable-active-high;
 106         };
 107 };
 108
 109 &eth0 {
 110         status = "okay";
 111
 112         nvmem-cells = <&macaddr_config_0>;
 113         nvmem-cell-names = "mac-address";
 114         mac-address-increment = <1>;
 115 };
 116
 117 &eth1 {
 118         status = "okay";
 119
 120         nvmem-cells = <&macaddr_config_0>;
 121         nvmem-cell-names = "mac-address";
 122 };
 123
 124 &spi {
 125         status = "okay";
 126
 127         flash@0 {
 128                 compatible = "jedec,spi-nor";
 129                 reg = <0>;
 130                 spi-max-frequency = <30000000>;
 131
 132                 partitions {
 133                         compatible = "fixed-partitions";
 134                         #address-cells = <1>;
 135                         #size-cells = <1>;
 136
 137                         partition@0 {
 138                                 label = "u-boot";
 139                                 reg = <0x0 0x20000>;
 140                                 read-only;
 141                         };
 142
 143                         config: partition@20000 {
 144                                 label = "config";
 145                                 reg = <0x20000 0x10000>;
 146                                 read-only;
 147
 148                                 nvmem-layout {
 149                                         compatible = "fixed-layout";
 150                                         #address-cells = <1>;
 151                                         #size-cells = <1>;
 152
 153                                         macaddr_config_0: macaddr@0 {
 154                                                 reg = <0x0 0x6>;
 155                                         };
 156                                 };
 157                         };
 158
 159                         art: partition@30000 {
 160                                 label = "art";
 161                                 reg = <0x30000 0x10000>;
 162                                 read-only;
 163                         };
 164
 165                         partition@40000 {
 166                                 compatible = "tplink,firmware";
 167                                 label = "firmware";
 168                                 reg = <0x40000 0xf30000>;
 169                         };
 170
 171                         partition@f70000 {
 172                                 label = "event-log";
 173                                 reg = <0xf70000 0x90000>;
 174                                 read-only;
 175                         };
 176                 };
 177         };
 178 };
 179
 180 &usb {
 181         dr_mode = "host";
 182         vbus-supply = <&reg_usb_vbus>;
 183         status = "okay";
 184 };
 185
 186 &gpio {
 187         modem-power {
 188                 gpio-hog;
 189                 output-low;
 190                 gpios = <18 GPIO_ACTIVE_HIGH>;
 191                 line-name = "modem-power";
 192         };
 193 };
 194
 195 &usb_phy {
 196         status = "okay";
 197 };
 198
 199 &wmac {
 200         status = "okay";
 201
 202         mtd-cal-data = <&art 0x1000>;
 203         nvmem-cells = <&macaddr_config_0>;
 204         nvmem-cell-names = "mac-address";
 205         mac-address-increment = <2>;
 206 };