};
soc {
- pinmux@800000 {
- i2c4_pins: i2c4_pinmux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- bias-disable;
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- drive-strength = <10>;
- bias-none;
- };
- };
- nand_pins: nand_pins {
- mux {
- pins = "gpio34", "gpio35", "gpio36",
- "gpio37", "gpio38", "gpio39",
- "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- function = "nand";
- drive-strength = <10>;
- bias-disable;
- };
- pullups {
- pins = "gpio39";
- bias-pull-up;
- };
- hold {
- pins = "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- bias-bus-hold;
- };
- };
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
+ <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "gpio";
- drive-strength = <8>;
- bias-disable;
- };
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ qca,ar8327-initvals = <
+ 0x00004 0x7600000 /* PAD0_MODE */
+ 0x00008 0x1000000 /* PAD5_MODE */
+ 0x0000c 0x80 /* PAD6_MODE */
+ 0x000e4 0x6a545 /* MAC_POWER_SEL */
+ 0x000e0 0xc74164de /* SGMII_CTRL */
+ 0x0007c 0x4e /* PORT0_STATUS */
+ 0x00094 0x4e /* PORT6_STATUS */
+ >;
};
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
+ phy4: ethernet-phy@4 {
+ reg = <4>;
};
};
+ };
+};
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "okay";
- serial@16340000 {
- status = "okay";
- };
+&qcom_pinmux {
+ i2c4_pins: i2c4_pinmux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ bias-disable;
+ };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
+ nand_pins: nand_pins {
+ mux {
+ pins = "gpio34", "gpio35", "gpio36",
+ "gpio37", "gpio38", "gpio39",
+ "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ function = "nand";
+ drive-strength = <10>;
+ bias-disable;
+ };
+ pullups {
+ pins = "gpio39";
+ bias-pull-up;
};
+ hold {
+ pins = "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ bias-bus-hold;
+ };
+ };
- gsbi5: gsbi@1a200000 {
- qcom,mode = <GSBI_PROT_SPI>;
- status = "okay";
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
- spi4: spi@1a280000 {
- status = "okay";
- spi-max-frequency = <50000000>;
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+};
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
+&adm_dma {
+ status = "okay";
+};
- cs-gpios = <&qcom_pinmux 20 0>;
+&gsbi4 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "okay";
- flash: m25p80@0 {
- compatible = "s25fl256s1";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <50000000>;
- reg = <0>;
+ serial@16340000 {
+ status = "okay";
+ };
- partitions {
- compatible = "qcom,smem";
- };
- };
- };
- };
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+};
- sata-phy@1b400000 {
- status = "okay";
- };
+&gsbi5 {
+ qcom,mode = <GSBI_PROT_SPI>;
+ status = "okay";
- sata@29000000 {
- status = "okay";
- };
+ spi4: spi@1a280000 {
+ status = "okay";
+ spi-max-frequency = <50000000>;
- usb3_0: usb3@110f8800 {
- status = "okay";
- };
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
- usb3_1: usb3@100f8800 {
- status = "okay";
- };
+ cs-gpios = <&qcom_pinmux 20 0>;
- pcie0: pci@1b500000 {
- status = "okay";
- };
+ flash: m25p80@0 {
+ compatible = "s25fl256s1";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <50000000>;
+ reg = <0>;
- pcie1: pci@1b700000 {
- status = "okay";
- force_gen1 = <1>;
+ partitions {
+ compatible = "qcom,smem";
+ };
};
+ };
+};
- nand@1ac00000 {
- status = "okay";
+&usb3_0 {
+ status = "okay";
+};
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
+&usb3_1 {
+ status = "okay";
+};
- cs0 {
- reg = <0>;
- compatible = "qcom,nandcs";
+&pcie0 {
+ status = "okay";
+};
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
+&pcie1 {
+ status = "okay";
+ force_gen1 = <1>;
+};
- partitions {
- compatible = "qcom,smem";
- };
- };
- };
+&nand {
+ status = "okay";
- mdio0: mdio {
- compatible = "virtual,mdio-gpio";
- #address-cells = <1>;
- #size-cells = <0>;
- gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
- phy0: ethernet-phy@0 {
- reg = <0>;
- qca,ar8327-initvals = <
- 0x00004 0x7600000 /* PAD0_MODE */
- 0x00008 0x1000000 /* PAD5_MODE */
- 0x0000c 0x80 /* PAD6_MODE */
- 0x000e4 0x6a545 /* MAC_POWER_SEL */
- 0x000e0 0xc74164de /* SGMII_CTRL */
- 0x0007c 0x4e /* PORT0_STATUS */
- 0x00094 0x4e /* PORT6_STATUS */
- >;
- };
+ cs0 {
+ reg = <0>;
+ compatible = "qcom,nandcs";
- phy4: ethernet-phy@4 {
- reg = <4>;
- };
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "qcom,smem";
};
+ };
+};
- gmac1: ethernet@37200000 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <1>;
+&gmac1 {
+ status = "okay";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
- gmac2: ethernet@37400000 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
+&gmac2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
};
};
-&adm_dma {
+&sata_phy {
+ status = "okay";
+};
+
+&sata {
status = "okay";
};
projects / openwrt / openwrt.git / commitdiff