Netgear Nighthawk RAX120v2 AX WIFI router with 5 1G and 1 5G ports.
The majority of the code is based on @jewwest's PR #11830.
Specifications:
* CPU: Qualcomm IPQ8074 Quad core Cortex-A53 2.2GHz
* RAM: 1024MB of DDR3 (Nanya NT5CC256M16EP-EK × 2)
* Flash: SPI-NAND 512 MiB (Winbond W29N04GZBIBA)
* Ethernet: 4x 10/100/1000 Mbps LAN,
1x 10/100/1000 Mbps WAN (Qualcomm QCA8075),
1x 10/100/1000/2500/5000 Mbps LAN/WAN (Aquantia AQR111B0 PHY)
* Wi-Fi:
* 2.4 GHz: Qualcomm QCN5024 4x4
* 2x 5 GHz: Qualcomm QCN5054 4x4
* USB: 2x USB 3.0
* LEDs: Power, 2.4GHz & 5GHz Radio, WPS, WAN, USB1 & USB2, 5G LAN
* Keys: LEDs On/Off, Power, Reset, RFKILL, WPS
* UART: Marked J9003 VCC TX RX GND, beginning from "1". 3.3v, 115200n8
* Power: 19 VDC, 3.1 A
Installation:
* Flashing OpenWrt is done in two steps:
a) Flash *-squashfs-web-ui-factory.img from stock UI (thanks to @wangyu-).
This writes an initramfs based OpenWrt image onto the RAX120v2
b) From OpenWrt flash the *-squashfs-sysupgrade.bin using LuCI or the commandline
* U-Boot allows booting an initramfs image via TFTP:
- Set ip of your PC to 192.168.1.100
- At the serial console interrupt boot at "Hit any key to stop autoboot:"
- In u-boot run `tftpsrv`
- On your PC send the OpenWrt initramfs image:
tftp 192.168.1.1 -m binary -c put openwrt-ipq807x-generic-netgear_rax120v2-initramfs-uImage.itb
Make 5G Aquantia phy work:
For the 5G port labeled 'lan5' to work a firmware is needed. This can be loaded in
u-boot by writing the firmware to the correct mtd partition.
The firmware file found in the Netgear stock firmware under /lib/firmware/ named
'AQR-G3_v4.3.C-AQR_DNI_DR-EQ35AX8-R-prov1_ID23888_VER1311.cld' is needed and has to
be converted to a MBN file.
The `mkheader.py` script used here can be found in the Netgear V1.2.8.40 GPL source,
under 'git_home/u-boot.git/tools/mkheader.py'
Convert the CLD file to MBN using:
$ python2 mkheader.py 0x44000000 0x13 <*.cld file> aqr_4.3.C.mbn
This MBN file can then be flashed to the MTD partition to be used by u-boot.
The necessary files can also be found in
https://github.com/boretom/openwrt-fork/tree/rax120v2/aquantia-firmware
* Write MBN file to MTD partition to be loaded automatically by u-boot:
U-boot automatically tries to load the firmware from nand at address 0x7e00000 which
corresponds to `/dev/mtd25` in OpenWrt.
- find ETHPHYFW partition while running OpenWrt (expected: /dev/mtd25)
$ fgrep -i 'ethphyfw' /proc/mtd
mtd25:
00080000 00020000 "ethphyfw
- copy mbn file to /tmp/ folder of the router
$ scp aqr-v4.3.C.mbn 192.168.1.1:/tmp/
- write mbn file to ethphyfw partition
$ mtd write /tmp/aqr_v4.3.C.mbn /dev/mtd25
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References to RAX120v2 GPL source:
https://www.downloads.netgear.com/files/GPL/RAX120-V1.2.8.40_gpl_src.zip
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
case "$board" in
dynalink,dl-wrx36|\
+netgear,rax120v2|\
netgear,wax218)
idx="$(find_mtd_index 0:appsblenv)"
[ -n "$idx" ] && \
dynalink_dl-wrx36 \
edgecore_eap102 \
edimax_cax1800 \
+ netgear_rax120v2 \
netgear_wax218 \
prpl_haze \
qnap_301w \
$(eval $(call generate-ipq-wifi-package,dynalink_dl-wrx36,Dynalink DL-WRX36))
$(eval $(call generate-ipq-wifi-package,edgecore_eap102,Edgecore EAP102))
$(eval $(call generate-ipq-wifi-package,edimax_cax1800,Edimax CAX1800))
+$(eval $(call generate-ipq-wifi-package,netgear_rax120v2,Netgear RAX120v2))
$(eval $(call generate-ipq-wifi-package,netgear_wax218,Netgear WAX218))
$(eval $(call generate-ipq-wifi-package,qnap_301w,QNAP 301w))
$(eval $(call generate-ipq-wifi-package,prpl_haze,prpl Haze))
--- /dev/null
+Author: Thomas Kupper <thomas.kupper@gmail.com>
+Date: Wed May 24 21:14:17 2023 +0200
+
+kernel: phy: add Aquantia PHY AQR111 & AQR111B0
+
+Add the IDs for Aquantia PHY AQR111 and AQR111B0 as found in the GPL sources
+of the Netgear RAX120v2 firmware v1.2.8.40.
+
+This is a 5GbE chip but it reports support for 10G. Implement config_init()
+to set max speed to 5G.
+
+Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
+--- a/drivers/net/phy/aquantia_main.c
++++ b/drivers/net/phy/aquantia_main.c
+@@ -20,6 +20,8 @@
+ #define PHY_ID_AQR105 0x03a1b4a2
+ #define PHY_ID_AQR106 0x03a1b4d0
+ #define PHY_ID_AQR107 0x03a1b4e0
++#define PHY_ID_AQR111 0x03a1b610
++#define PHY_ID_AQR111B0 0x03a1b612
+ #define PHY_ID_AQR112 0x03a1b662
+ #define PHY_ID_AQR112C 0x03a1b790
+ #define PHY_ID_AQR112R 0x31c31d12
+@@ -686,6 +688,33 @@ static int aqcs109_config_init(struct ph
+ return aqr107_set_downshift(phydev, MDIO_AN_VEND_PROV_DOWNSHIFT_DFLT);
+ }
+
++static int aqr111_config_init(struct phy_device *phydev)
++{
++ int ret;
++
++ /* Check that the PHY interface type is compatible */
++ if (phydev->interface != PHY_INTERFACE_MODE_SGMII &&
++ phydev->interface != PHY_INTERFACE_MODE_2500BASEX &&
++ phydev->interface != PHY_INTERFACE_MODE_XGMII &&
++ phydev->interface != PHY_INTERFACE_MODE_USXGMII &&
++ phydev->interface != PHY_INTERFACE_MODE_10GKR &&
++ phydev->interface != PHY_INTERFACE_MODE_10GBASER)
++ return -ENODEV;
++
++ WARN(phydev->interface == PHY_INTERFACE_MODE_XGMII,
++ "Your devicetree is out of date, please update it. The AQR107 family doesn't support XGMII, maybe you mean USXGMII.\n");
++
++ ret = aqr107_wait_reset_complete(phydev);
++ if (!ret)
++ aqr107_chip_info(phydev);
++
++ /* AQR111 reports supporting speed up to 10G, however only speeds up to 5G are supported. */
++ ret = phy_set_max_speed(phydev, SPEED_5000);
++ if (ret)
++ return ret;
++
++ return aqr107_set_downshift(phydev, MDIO_AN_VEND_PROV_DOWNSHIFT_DFLT);
++}
+ static void aqr107_link_change_notify(struct phy_device *phydev)
+ {
+ u8 fw_major, fw_minor;
+@@ -905,6 +934,42 @@ static struct phy_driver aqr_driver[] =
+ .link_change_notify = aqr107_link_change_notify,
+ },
+ {
++ PHY_ID_MATCH_MODEL(PHY_ID_AQR111),
++ .name = "Aquantia AQR111",
++ .probe = aqr107_probe,
++ .config_init = aqr111_config_init,
++ .config_aneg = aqr_config_aneg,
++ .config_intr = aqr_config_intr,
++ .handle_interrupt = aqr_handle_interrupt,
++ .read_status = aqr107_read_status,
++ .get_tunable = aqr107_get_tunable,
++ .set_tunable = aqr107_set_tunable,
++ .suspend = aqr107_suspend,
++ .resume = aqr107_resume,
++ .get_sset_count = aqr107_get_sset_count,
++ .get_strings = aqr107_get_strings,
++ .get_stats = aqr107_get_stats,
++ .link_change_notify = aqr107_link_change_notify,
++},
++{
++ PHY_ID_MATCH_MODEL(PHY_ID_AQR111B0),
++ .name = "Aquantia AQR111B0",
++ .probe = aqr107_probe,
++ .config_init = aqr111_config_init,
++ .config_aneg = aqr_config_aneg,
++ .config_intr = aqr_config_intr,
++ .handle_interrupt = aqr_handle_interrupt,
++ .read_status = aqr107_read_status,
++ .get_tunable = aqr107_get_tunable,
++ .set_tunable = aqr107_set_tunable,
++ .suspend = aqr107_suspend,
++ .resume = aqr107_resume,
++ .get_sset_count = aqr107_get_sset_count,
++ .get_strings = aqr107_get_strings,
++ .get_stats = aqr107_get_stats,
++ .link_change_notify = aqr107_link_change_notify,
++},
++{
+ PHY_ID_MATCH_MODEL(PHY_ID_AQR112),
+ .name = "Aquantia AQR112",
+ .probe = aqr107_probe,
+@@ -970,6 +1035,8 @@ static struct mdio_device_id __maybe_unu
+ { PHY_ID_MATCH_MODEL(PHY_ID_AQR105) },
+ { PHY_ID_MATCH_MODEL(PHY_ID_AQR106) },
+ { PHY_ID_MATCH_MODEL(PHY_ID_AQR107) },
++ { PHY_ID_MATCH_MODEL(PHY_ID_AQR111) },
++ { PHY_ID_MATCH_MODEL(PHY_ID_AQR111B0) },
+ { PHY_ID_MATCH_MODEL(PHY_ID_AQR112) },
+ { PHY_ID_MATCH_MODEL(PHY_ID_AQR112C) },
+ { PHY_ID_MATCH_MODEL(PHY_ID_AQR112R) },
--- /dev/null
+Author: Thomas Kupper <thomas.kupper@gmail.com>
+Date: Wed May 24 21:14:17 2023 +0200
+
+kernel: phy: add Aquantia PHY AQR111 & AQR111B0
+
+Add the IDs for Aquantia PHY AQR111 and AQR111B0 as found in the GPL sources
+of the Netgear RAX120v2 firmware v1.2.8.40.
+
+This is a 5GbE chip but it reports support for 10G. Implement config_init()
+to set max speed to 5G.
+
+Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
+--- a/drivers/net/phy/aquantia_main.c
++++ b/drivers/net/phy/aquantia_main.c
+@@ -24,6 +24,8 @@
+ #define PHY_ID_AQR405 0x03a1b4b0
+ #define PHY_ID_AQR113C 0x31c31c12
+ #define PHY_ID_AQR813 0x31c31cb2
++#define PHY_ID_AQR111 0x03a1b610
++#define PHY_ID_AQR111B0 0x03a1b612
+ #define PHY_ID_AQR112 0x03a1b662
+ #define PHY_ID_AQR412 0x03a1b712
+ #define PHY_ID_AQR113 0x31c31c40
+@@ -729,6 +731,34 @@ static int aqcs109_config_init(struct ph
+ return aqr107_set_downshift(phydev, MDIO_AN_VEND_PROV_DOWNSHIFT_DFLT);
+ }
+
++static int aqr111_config_init(struct phy_device *phydev)
++{
++ int ret;
++
++ /* Check that the PHY interface type is compatible */
++ if (phydev->interface != PHY_INTERFACE_MODE_SGMII &&
++ phydev->interface != PHY_INTERFACE_MODE_1000BASEKX &&
++ phydev->interface != PHY_INTERFACE_MODE_2500BASEX &&
++ phydev->interface != PHY_INTERFACE_MODE_XGMII &&
++ phydev->interface != PHY_INTERFACE_MODE_USXGMII &&
++ phydev->interface != PHY_INTERFACE_MODE_10GKR &&
++ phydev->interface != PHY_INTERFACE_MODE_10GBASER &&
++ phydev->interface != PHY_INTERFACE_MODE_XAUI &&
++ phydev->interface != PHY_INTERFACE_MODE_RXAUI)
++ return -ENODEV;
++
++ WARN(phydev->interface == PHY_INTERFACE_MODE_XGMII,
++ "Your devicetree is out of date, please update it. The AQR107 family doesn't support XGMII, maybe you mean USXGMII.\n");
++
++ ret = aqr107_wait_reset_complete(phydev);
++ if (!ret)
++ aqr107_chip_info(phydev);
++
++ /* AQR111 reports supporting speed up to 10G, however only speeds up to 5G are supported. */
++ phy_set_max_speed(phydev, SPEED_5000);
++
++ return aqr107_set_downshift(phydev, MDIO_AN_VEND_PROV_DOWNSHIFT_DFLT);
++}
+ static void aqr107_link_change_notify(struct phy_device *phydev)
+ {
+ u8 fw_major, fw_minor;
+@@ -961,6 +991,42 @@ static struct phy_driver aqr_driver[] =
+ .link_change_notify = aqr107_link_change_notify,
+ },
+ {
++ PHY_ID_MATCH_MODEL(PHY_ID_AQR111),
++ .name = "Aquantia AQR111",
++ .probe = aqr107_probe,
++ .config_init = aqr111_config_init,
++ .config_aneg = aqr_config_aneg,
++ .config_intr = aqr_config_intr,
++ .handle_interrupt = aqr_handle_interrupt,
++ .read_status = aqr107_read_status,
++ .get_tunable = aqr107_get_tunable,
++ .set_tunable = aqr107_set_tunable,
++ .suspend = aqr107_suspend,
++ .resume = aqr107_resume,
++ .get_sset_count = aqr107_get_sset_count,
++ .get_strings = aqr107_get_strings,
++ .get_stats = aqr107_get_stats,
++ .link_change_notify = aqr107_link_change_notify,
++},
++{
++ PHY_ID_MATCH_MODEL(PHY_ID_AQR111B0),
++ .name = "Aquantia AQR111B0",
++ .probe = aqr107_probe,
++ .config_init = aqr111_config_init,
++ .config_aneg = aqr_config_aneg,
++ .config_intr = aqr_config_intr,
++ .handle_interrupt = aqr_handle_interrupt,
++ .read_status = aqr107_read_status,
++ .get_tunable = aqr107_get_tunable,
++ .set_tunable = aqr107_set_tunable,
++ .suspend = aqr107_suspend,
++ .resume = aqr107_resume,
++ .get_sset_count = aqr107_get_sset_count,
++ .get_strings = aqr107_get_strings,
++ .get_stats = aqr107_get_stats,
++ .link_change_notify = aqr107_link_change_notify,
++},
++{
+ PHY_ID_MATCH_MODEL(PHY_ID_AQR112),
+ .name = "Aquantia AQR112",
+ .probe = aqr107_probe,
+@@ -1030,6 +1096,8 @@ static struct mdio_device_id __maybe_unu
+ { PHY_ID_MATCH_MODEL(PHY_ID_AQR405) },
+ { PHY_ID_MATCH_MODEL(PHY_ID_AQR113C) },
+ { PHY_ID_MATCH_MODEL(PHY_ID_AQR813) },
++ { PHY_ID_MATCH_MODEL(PHY_ID_AQR111) },
++ { PHY_ID_MATCH_MODEL(PHY_ID_AQR111B0) },
+ { PHY_ID_MATCH_MODEL(PHY_ID_AQR112) },
+ { PHY_ID_MATCH_MODEL(PHY_ID_AQR412) },
+ { PHY_ID_MATCH_MODEL(PHY_ID_AQR113) },
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include "ipq8074.dtsi"
+#include "ipq8074-ess.dtsi"
+#include "ipq8074-hk-cpu.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Netgear RAX120v2";
+ compatible = "netgear,rax120v2", "qcom,ipq8074";
+
+ aliases {
+ serial0 = &blsp1_uart5;
+
+ led-running = &led_system_white;
+ led-upgrade = &led_system_white;
+ led-internet = &led_wan_white;
+ label-mac-device = &dp1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs-append = " ubi.mtd=rootfs root=/dev/ubiblock0_0";
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ rfkill {
+ label = "rfkill";
+ gpios = <&tlmm 25 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 57 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 54 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ led_spi {
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sck-gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+ mosi-gpios = <&tlmm 19 GPIO_ACTIVE_HIGH>;
+
+ led_gpio: led_gpio@0 {
+ compatible = "fairchild,74hc595";
+ reg = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ registers-number = <2>;
+ enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>;
+ spi-max-frequency = <1000000>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_system_white: system-white {
+ label = "white:system";
+ gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_WHITE>;
+ };
+
+ led_24g_white {
+ label = "white:24g";
+ gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_WHITE>;
+ linux,default-trigger = "phy1radio";
+ };
+
+ led_5g_white {
+ label = "white:5g";
+ gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_WHITE>;
+ linux,default-trigger = "phy0radio";
+ };
+
+ led_usb1_white {
+ label = "white:usb1";
+ gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_WHITE>;
+ };
+
+ led_usb2_white {
+ label = "white:usb2";
+ gpios = <&led_gpio 4 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_WHITE>;
+ };
+
+ led_wan_white: wan-white {
+ label = "white:wan";
+ gpios = <&led_gpio 5 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_WHITE>;
+ };
+
+ led_aqr_green {
+ label = "green:aqr";
+ gpios = <&led_gpio 6 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_GREEN>;
+ };
+
+ led_aqr_red {
+ label = "red:aqr";
+ gpios = <&led_gpio 10 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_RED>;
+ };
+
+ led_aqr_white {
+ label = "white:aqr";
+ gpios = <&led_gpio 11 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_WHITE>;
+ };
+
+ led_wps_white {
+ label = "white:wps";
+ gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>;
+ color = <LED_COLOR_ID_WHITE>;
+ };
+ };
+};
+
+&tlmm {
+ mdio_pins: mdio-pins {
+ mdc {
+ pins = "gpio68";
+ function = "mdc";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ mdio {
+ pins = "gpio69";
+ function = "mdio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>;
+
+ qca8075_0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+
+ qca8075_1: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+
+ qca8075_2: ethernet-phy@2 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <2>;
+ };
+
+ qca8075_3: ethernet-phy@3 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <3>;
+ };
+
+ qca8075_4: ethernet-phy@4 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <4>;
+ };
+
+ aqr111b0: ethernet-phy@7 {
+ compatible ="ethernet-phy-ieee802.3-c45";
+ reg = <7>;
+ reset-gpios = <&tlmm 59 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&switch {
+ status = "okay";
+
+ switch_lan_bmp = <0x3e>; /* lan port bitmap */
+ switch_wan_bmp = <0x40>; /* wan port bitmap */
+ switch_mac_mode = <0x0>; /* mac mode for uniphy instance0*/
+ switch_mac_mode1 = <0xff>; /* mac mode for uniphy instance1*/
+ switch_mac_mode2 = <0xd>; /* mac mode for uniphy instance2*/
+ bm_tick_mode = <0>; /* bm tick mode */
+ tm_tick_mode = <0>; /* tm tick mode */
+
+ qcom,port_phyinfo {
+ port@1 {
+ port_id = <1>;
+ phy_address = <0>;
+ };
+ port@2 {
+ port_id = <2>;
+ phy_address = <1>;
+ };
+ port@3 {
+ port_id = <3>;
+ phy_address = <2>;
+ };
+ port@4 {
+ port_id = <4>;
+ phy_address = <3>;
+ };
+ port@5 {
+ port_id = <5>;
+ phy_address = <4>;
+ };
+ port@6 {
+ port_id = <6>;
+ phy_address = <7>;
+ compatible = "ethernet-phy-ieee802.3-c45";
+ ethernet-phy-ieee802.3-c45;
+ };
+ };
+};
+
+&edma {
+ status = "okay";
+};
+
+&dp1 {
+ status = "okay";
+ phy-handle = <&qca8075_0>;
+ label = "lan4";
+ nvmem-cells = <&macaddr_dp1>;
+ nvmem-cell-names = "mac-address";
+};
+
+&dp2 {
+ status = "okay";
+ phy-handle = <&qca8075_1>;
+ label = "lan3";
+ nvmem-cells = <&macaddr_dp2>;
+ nvmem-cell-names = "mac-address";
+};
+
+&dp3 {
+ status = "okay";
+ phy-handle = <&qca8075_2>;
+ label = "lan2";
+ nvmem-cells = <&macaddr_dp3>;
+ nvmem-cell-names = "mac-address";
+};
+
+&dp4 {
+ status = "okay";
+ phy-handle = <&qca8075_3>;
+ label = "lan1";
+ nvmem-cells = <&macaddr_dp4>;
+ nvmem-cell-names = "mac-address";
+};
+
+&dp5 {
+ status = "okay";
+ phy-handle = <&qca8075_4>;
+ label = "wan";
+ nvmem-cells = <&macaddr_dp5>;
+ nvmem-cell-names = "mac-address";
+};
+
+&dp6_syn {
+ status = "okay";
+ phy-handle = <&aqr111b0>;
+ label = "lan5";
+ nvmem-cells = <&macaddr_dp6_syn>;
+ nvmem-cell-names = "mac-address";
+};
+
+&blsp1_uart5 {
+ status = "okay";
+};
+
+&blsp1_i2c2 {
+ status = "okay";
+
+ g761@3e {
+ compatible = "gmt,g763";
+ reg = <0x3e>;
+ clocks =<&sleep_clk>;
+ fan_gear_mode = <0>;
+ fan_start = <1>;
+ pwm_polarity = <0>;
+ };
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&qpic_nand {
+ status = "okay";
+
+ nand@0 {
+ reg = <0>;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ nand-bus-width = <8>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "0:sbl1";
+ reg = <0x00 0x100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "0:mibib";
+ reg = <0x100000 0x100000>;
+ read-only;
+ };
+
+ partition@200000 {
+ label = "0:bootconfig";
+ reg = <0x200000 0x80000>;
+ read-only;
+ };
+
+ partition@280000 {
+ label = "0:bootconfig_1";
+ reg = <0x280000 0x80000>;
+ read-only;
+ };
+
+ partition@300000 {
+ label = "0:qsee";
+ reg = <0x300000 0x300000>;
+ read-only;
+ };
+
+ partition@600000 {
+ label = "0:qsee_1";
+ reg = <0x600000 0x300000>;
+ read-only;
+ };
+
+ partition@900000 {
+ label = "0:devcfg";
+ reg = <0x900000 0x80000>;
+ read-only;
+ };
+
+ partition@980000 {
+ label = "0:devcfg_1";
+ reg = <0x980000 0x80000>;
+ read-only;
+ };
+
+ partition@a00000 {
+ label = "0:apdp";
+ reg = <0xa00000 0x80000>;
+ read-only;
+ };
+
+ partition@a80000 {
+ label = "0:apdp_1";
+ reg = <0xa80000 0x80000>;
+ read-only;
+ };
+
+ partition@b00000 {
+ label = "0:rpm";
+ reg = <0xb00000 0x80000>;
+ read-only;
+ };
+
+ partition@b80000 {
+ label = "0:rpm_1";
+ reg = <0xb80000 0x80000>;
+ read-only;
+ };
+
+ partition@c00000 {
+ label = "0:cdt";
+ reg = <0xc00000 0x80000>;
+ read-only;
+ };
+
+ partition@c80000 {
+ label = "0:cdt_1";
+ reg = <0xc80000 0x80000>;
+ read-only;
+ };
+
+ partition@d00000 {
+ label = "0:appsblenv";
+ reg = <0xd00000 0x80000>;
+ };
+
+ partition@d80000 {
+ label = "0:appsbl";
+ reg = <0xd80000 0x100000>;
+ read-only;
+ };
+
+ partition@e80000 {
+ label = "0:appsbl_1";
+ reg = <0xe80000 0x100000>;
+ read-only;
+ };
+
+ partition@f80000 {
+ label = "0:art";
+ reg = <0xf80000 0x80000>;
+ read-only;
+ };
+
+ partition@1000000 {
+ label = "0:art.bak";
+ reg = <0x1000000 0x0080000>;
+ read-only;
+ };
+
+ partition@1080000 {
+ label = "config";
+ reg = <0x1080000 0x0100000>;
+ read-only;
+ };
+
+ partition@1180000 {
+ label = "boarddata1";
+ reg = <0x1180000 0x0100000>;
+ read-only;
+
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_dp1: macaddr@0 {
+ reg = <0x0 0x6>;
+ };
+
+ macaddr_dp2: macaddr@1 {
+ reg = <0x6 0x6>;
+ };
+
+ macaddr_dp3: macaddr@2 {
+ reg = <0xc 0x6>;
+ };
+
+ macaddr_dp4: macaddr@3 {
+ reg = <0x12 0x6>;
+ };
+
+ macaddr_dp5: macaddr@4 {
+ reg = <0x18 0x6>;
+ };
+
+ macaddr_dp6_syn: macaddr@5 {
+ reg = <0x1e 0x6>;
+ };
+
+ };
+
+ partition@1280000 {
+ label = "boarddata2";
+ reg = <0x1280000 0x0100000>;
+ read-only;
+ };
+
+ partition@1380000 {
+ label = "pot";
+ reg = <0x1380000 0x0100000>;
+ read-only;
+ };
+
+ partition@1480000 {
+ label = "dnidata";
+ reg = <0x1480000 0x0500000>;
+ read-only;
+ };
+
+ partition@1980000 {
+ label = "kernel";
+ reg = <0x1980000 0x1d00000>;
+ };
+
+ partition@7e00000 {
+ label = "ethphyfw";
+ reg = <0x7e00000 0x80000>;
+ };
+
+ partition@e8800000 {
+ label = "rootfs";
+ reg = <0xe880000 0x11780000>;
+ };
+ };
+ };
+};
+
+&qusb_phy_0 {
+ status = "okay";
+};
+
+&qusb_phy_1 {
+ status = "okay";
+};
+
+&ssphy_0 {
+ status = "okay";
+};
+
+&ssphy_1 {
+ status = "okay";
+};
+
+&usb_0 {
+ status = "okay";
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&wifi{
+ status = "okay";
+
+ qcom,ath11k-calibration-variant = "Netgear-RAX120v2";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&crypto {
+ status = "okay";
+};
+
+&prng {
+ status = "okay";
+};
endef
TARGET_DEVICES += edimax_cax1800
+define Device/netgear_rax120v2
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ DEVICE_VENDOR := Netgear
+ DEVICE_MODEL := RAX120v2
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ DEVICE_DTS_CONFIG := config@hk01
+ SOC := ipq8074
+ KERNEL_SIZE := 29696k
+ NETGEAR_BOARD_ID := RAX120
+ NETGEAR_HW_ID := 29765589+0+512+1024+4x4+8x8
+ DEVICE_PACKAGES := ipq-wifi-netgear_rax120v2 kmod-spi-gpio \
+ kmod-spi-bitbang kmod-gpio-nxp-74hc164 kmod-hwmon-g761
+ IMAGES = web-ui-factory.img sysupgrade.bin
+ IMAGE/web-ui-factory.img := append-image initramfs-uImage.itb | \
+ pad-offset $$$$(BLOCKSIZE) 64 | append-uImage-fakehdr filesystem | \
+ netgear-dni
+ IMAGE/sysupgrade.bin := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | \
+ append-uImage-fakehdr filesystem | sysupgrade-tar kernel=$$$$@ | \
+ append-metadata
+endef
+TARGET_DEVICES += netgear_rax120v2
+
define Device/netgear_wax218
$(call Device/FitImage)
$(call Device/UbiFit)
edgecore,eap102)
ucidef_set_led_netdev "wan" "WAN" "green:wanpoe" "wan"
;;
+netgear,rax120v2)
+ ucidef_set_led_netdev "aqr" "AQR" "white:aqr" "lan5"
+ ;;
netgear,wax218)
ucidef_set_led_netdev "lan" "LAN" "blue:lan" "lan"
ucidef_set_led_wlan "wlan5g" "WIFI 5GHz" "blue:wlan5g" "phy0radio"
edimax,cax1800)
ucidef_set_interfaces_lan_wan "lan"
;;
+ netgear,rax120v2)
+ ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5" "wan"
+ ;;
netgear,wax218)
ucidef_set_interface_lan "lan" "dhcp"
;;
edgecore,eap102|\
edimax,cax1800|\
dynalink,dl-wrx36|\
+ netgear,rax120v2|\
netgear,wax218|\
qnap,301w|\
redmi,ax6|\
;;
compex,wpq873|\
edimax,cax1800|\
+ netgear,rax120v2|\
netgear,wax218)
nand_do_upgrade "$1"
;;
projects / openwrt / openwrt.git / commitdiff