-LINUX_VERSION-6.1 = .38
-LINUX_KERNEL_HASH-6.1.38 = f9a4f91b609f7d332a5f2be01ab86336fa00149fae6bdc19f16fa19f78802d43
\ No newline at end of file
+LINUX_VERSION-6.1 = .39
+LINUX_KERNEL_HASH-6.1.39 = 4cddee22fdf657138a06af653492f67cd3a4762c04a34725534bd200d99085b8
\ No newline at end of file
+++ /dev/null
-From 5365030a003a6cb0c336202256341e4bc9d65d52 Mon Sep 17 00:00:00 2001
-From: Dave Stevenson <dave.stevenson@raspberrypi.com>
-Date: Thu, 16 Dec 2021 15:25:35 +0000
-Subject: [PATCH] drm/bridge: Introduce pre_enable_upstream_first to
- alter bridge init order
-
-DSI sink devices typically want the DSI host powered up and configured
-before they are powered up. pre_enable is the place this would normally
-happen, but they are called in reverse order from panel/connector towards
-the encoder, which is the "wrong" order.
-
-Add a new flag pre_enable_upstream_first that any bridge can set
-to swap the order of pre_enable (and post_disable) for that and the
-immediately upstream bridge.
-Should the immediately upstream bridge also set the
-pre_enable_upstream_first flag, the bridge upstream of that will be called
-before either of those which requested pre_enable_upstream_first.
-
-eg:
-- Panel
-- Bridge 1
-- Bridge 2 pre_enable_upstream_first
-- Bridge 3
-- Bridge 4 pre_enable_upstream_first
-- Bridge 5 pre_enable_upstream_first
-- Bridge 6
-- Encoder
-Would result in pre_enable's being called as Panel, Bridge 1, Bridge 3,
-Bridge 2, Bridge 6, Bridge 5, Bridge 4, Encoder.
-
-Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
----
- drivers/gpu/drm/drm_bridge.c | 177 +++++++++++++++++++++++++----------
- include/drm/drm_bridge.h | 8 ++
- 2 files changed, 137 insertions(+), 48 deletions(-)
-
---- a/drivers/gpu/drm/drm_bridge.c
-+++ b/drivers/gpu/drm/drm_bridge.c
-@@ -547,20 +547,15 @@ EXPORT_SYMBOL(drm_bridge_chain_disable);
- * encoder chain, starting from the first bridge to the last. These are called
- * after completing the encoder's prepare op.
- *
-+ * If a bridge sets @pre_enable_upstream_first, then the @post_disable for that
-+ * bridge will be called before the previous one to reverse the @pre_enable
-+ * calling direction.
-+ *
- * Note: the bridge passed should be the one closest to the encoder
- */
- void drm_bridge_chain_post_disable(struct drm_bridge *bridge)
- {
-- struct drm_encoder *encoder;
--
-- if (!bridge)
-- return;
--
-- encoder = bridge->encoder;
-- list_for_each_entry_from(bridge, &encoder->bridge_chain, chain_node) {
-- if (bridge->funcs->post_disable)
-- bridge->funcs->post_disable(bridge);
-- }
-+ drm_atomic_bridge_chain_post_disable(bridge, NULL);
- }
- EXPORT_SYMBOL(drm_bridge_chain_post_disable);
-
-@@ -602,24 +597,14 @@ EXPORT_SYMBOL(drm_bridge_chain_mode_set)
- * chain, starting from the last bridge to the first. These are called
- * before calling the encoder's commit op.
- *
-+ * If a bridge sets @pre_enable_upstream_first, then the @pre_enable for the
-+ * previous bridge will be called before @pre_enable of this bridge.
-+ *
- * Note: the bridge passed should be the one closest to the encoder
- */
- void drm_bridge_chain_pre_enable(struct drm_bridge *bridge)
- {
-- struct drm_encoder *encoder;
-- struct drm_bridge *iter;
--
-- if (!bridge)
-- return;
--
-- encoder = bridge->encoder;
-- list_for_each_entry_reverse(iter, &encoder->bridge_chain, chain_node) {
-- if (iter->funcs->pre_enable)
-- iter->funcs->pre_enable(iter);
--
-- if (iter == bridge)
-- break;
-- }
-+ drm_atomic_bridge_chain_pre_enable(bridge, NULL);
- }
- EXPORT_SYMBOL(drm_bridge_chain_pre_enable);
-
-@@ -691,6 +676,25 @@ void drm_atomic_bridge_chain_disable(str
- }
- EXPORT_SYMBOL(drm_atomic_bridge_chain_disable);
-
-+static void drm_atomic_bridge_call_post_disable(struct drm_bridge *bridge,
-+ struct drm_atomic_state *old_state)
-+{
-+ if (old_state && bridge->funcs->atomic_post_disable) {
-+ struct drm_bridge_state *old_bridge_state;
-+
-+ old_bridge_state =
-+ drm_atomic_get_old_bridge_state(old_state,
-+ bridge);
-+ if (WARN_ON(!old_bridge_state))
-+ return;
-+
-+ bridge->funcs->atomic_post_disable(bridge,
-+ old_bridge_state);
-+ } else if (bridge->funcs->post_disable) {
-+ bridge->funcs->post_disable(bridge);
-+ }
-+}
-+
- /**
- * drm_atomic_bridge_chain_post_disable - cleans up after disabling all bridges
- * in the encoder chain
-@@ -701,6 +705,9 @@ EXPORT_SYMBOL(drm_atomic_bridge_chain_di
- * &drm_bridge_funcs.post_disable) op for all the bridges in the encoder chain,
- * starting from the first bridge to the last. These are called after completing
- * &drm_encoder_helper_funcs.atomic_disable
-+ * If a bridge sets @pre_enable_upstream_first, then the @post_disable for that
-+ * bridge will be called before the previous one to reverse the @pre_enable
-+ * calling direction.
- *
- * Note: the bridge passed should be the one closest to the encoder
- */
-@@ -708,30 +715,75 @@ void drm_atomic_bridge_chain_post_disabl
- struct drm_atomic_state *old_state)
- {
- struct drm_encoder *encoder;
-+ struct drm_bridge *next, *limit;
-
- if (!bridge)
- return;
-
- encoder = bridge->encoder;
-+
- list_for_each_entry_from(bridge, &encoder->bridge_chain, chain_node) {
-- if (bridge->funcs->atomic_post_disable) {
-- struct drm_bridge_state *old_bridge_state;
-+ limit = NULL;
-
-- old_bridge_state =
-- drm_atomic_get_old_bridge_state(old_state,
-- bridge);
-- if (WARN_ON(!old_bridge_state))
-- return;
-+ if (!list_is_last(&bridge->chain_node, &encoder->bridge_chain)) {
-+ next = list_next_entry(bridge, chain_node);
-
-- bridge->funcs->atomic_post_disable(bridge,
-- old_bridge_state);
-- } else if (bridge->funcs->post_disable) {
-- bridge->funcs->post_disable(bridge);
-+ if (next->pre_enable_upstream_first) {
-+ /* Downstream bridge had requested that upstream
-+ * was enabled first, so disabled last
-+ */
-+ limit = next;
-+
-+ /* Find the next bridge that has NOT requested
-+ * upstream to be enabled first / disabled last
-+ */
-+ list_for_each_entry_from(next, &encoder->bridge_chain,
-+ chain_node) {
-+ if (next->pre_enable_upstream_first) {
-+ next = list_prev_entry(next, chain_node);
-+ limit = next;
-+ break;
-+ }
-+ }
-+
-+ /* Call these bridges in reverse order */
-+ list_for_each_entry_from_reverse(next, &encoder->bridge_chain,
-+ chain_node) {
-+ if (next == bridge)
-+ break;
-+
-+ drm_atomic_bridge_call_post_disable(next,
-+ old_state);
-+ }
-+ }
- }
-+
-+ drm_atomic_bridge_call_post_disable(bridge, old_state);
-+
-+ if (limit)
-+ bridge = limit;
- }
- }
- EXPORT_SYMBOL(drm_atomic_bridge_chain_post_disable);
-
-+static void drm_atomic_bridge_call_pre_enable(struct drm_bridge *bridge,
-+ struct drm_atomic_state *old_state)
-+{
-+ if (old_state && bridge->funcs->atomic_pre_enable) {
-+ struct drm_bridge_state *old_bridge_state;
-+
-+ old_bridge_state =
-+ drm_atomic_get_old_bridge_state(old_state,
-+ bridge);
-+ if (WARN_ON(!old_bridge_state))
-+ return;
-+
-+ bridge->funcs->atomic_pre_enable(bridge, old_bridge_state);
-+ } else if (bridge->funcs->pre_enable) {
-+ bridge->funcs->pre_enable(bridge);
-+ }
-+}
-+
- /**
- * drm_atomic_bridge_chain_pre_enable - prepares for enabling all bridges in
- * the encoder chain
-@@ -743,33 +795,62 @@ EXPORT_SYMBOL(drm_atomic_bridge_chain_po
- * starting from the last bridge to the first. These are called before calling
- * &drm_encoder_helper_funcs.atomic_enable
- *
-+ * If a bridge sets @pre_enable_upstream_first, then the pre_enable for the
-+ * upstream bridge will be called before pre_enable of this bridge.
-+ *
- * Note: the bridge passed should be the one closest to the encoder
- */
- void drm_atomic_bridge_chain_pre_enable(struct drm_bridge *bridge,
- struct drm_atomic_state *old_state)
- {
- struct drm_encoder *encoder;
-- struct drm_bridge *iter;
-+ struct drm_bridge *iter, *next, *limit;
-
- if (!bridge)
- return;
-
- encoder = bridge->encoder;
-- list_for_each_entry_reverse(iter, &encoder->bridge_chain, chain_node) {
-- if (iter->funcs->atomic_pre_enable) {
-- struct drm_bridge_state *old_bridge_state;
-
-- old_bridge_state =
-- drm_atomic_get_old_bridge_state(old_state,
-- iter);
-- if (WARN_ON(!old_bridge_state))
-- return;
-+ list_for_each_entry_reverse(iter, &encoder->bridge_chain, chain_node) {
-+ if (iter->pre_enable_upstream_first) {
-+ next = iter;
-+ limit = bridge;
-+ list_for_each_entry_from_reverse(next,
-+ &encoder->bridge_chain,
-+ chain_node) {
-+ if (next == bridge)
-+ break;
-+
-+ if (!next->pre_enable_upstream_first) {
-+ /* Found first bridge that does NOT
-+ * request upstream to be enabled first
-+ */
-+ limit = list_prev_entry(next, chain_node);
-+ break;
-+ }
-+ }
-+
-+ list_for_each_entry_from(next, &encoder->bridge_chain, chain_node) {
-+ /* Call requested upstream bridge pre_enable
-+ * in order.
-+ */
-+ if (next == iter)
-+ /* At the first bridgge to request upstream
-+ * bridges called first.
-+ */
-+ break;
-
-- iter->funcs->atomic_pre_enable(iter, old_bridge_state);
-- } else if (iter->funcs->pre_enable) {
-- iter->funcs->pre_enable(iter);
-+ drm_atomic_bridge_call_pre_enable(next, old_state);
-+ }
- }
-
-+ drm_atomic_bridge_call_pre_enable(iter, old_state);
-+
-+ if (iter->pre_enable_upstream_first)
-+ /* Jump all bridges that we have already pre_enabled
-+ */
-+ iter = limit;
-+
- if (iter == bridge)
- break;
- }
---- a/include/drm/drm_bridge.h
-+++ b/include/drm/drm_bridge.h
-@@ -769,6 +769,14 @@ struct drm_bridge {
- */
- bool interlace_allowed;
- /**
-+ * @pre_enable_upstream_first: The bridge requires that the upstream
-+ * bridge @pre_enable function is called before its @pre_enable,
-+ * and conversely for post_disable. This is most frequently a
-+ * requirement for DSI devices which need the host to be initialised
-+ * before the peripheral.
-+ */
-+ bool pre_enable_upstream_first;
-+ /**
- * @ddc: Associated I2C adapter for DDC access, if any.
- */
- struct i2c_adapter *ddc;
-From 9ac3eedd8cda7d5f2429edc0bdba137c35e07157 Mon Sep 17 00:00:00 2001
+From 5ea6b17027810ffbdb5bea7d0a2b1d312dd1021c Mon Sep 17 00:00:00 2001
From: Dave Stevenson <dave.stevenson@raspberrypi.com>
-Date: Wed, 23 Feb 2022 15:36:56 +0000
-Subject: [PATCH] drm/panel: Add prepare_upstream_first flag to
- drm_panel
+Date: Mon, 5 Dec 2022 17:33:27 +0000
+Subject: [PATCH] drm/panel: Add prepare_prev_first flag to drm_panel
-Mapping to the drm_bridge flag pre_enable_upstream_first,
-add a new flag prepare_upstream_first to drm_panel to allow
+Mapping to the drm_bridge flag pre_enable_prev_first,
+add a new flag prepare_prev_first to drm_panel to allow
the panel driver to request that the upstream bridge should
be pre_enabled before the panel prepare.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
+Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
+Link: https://lore.kernel.org/r/20221205173328.1395350-6-dave.stevenson@raspberrypi.com
+Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
- drivers/gpu/drm/bridge/panel.c | 3 +++
+ drivers/gpu/drm/bridge/panel.c | 2 ++
include/drm/drm_panel.h | 10 ++++++++++
- 2 files changed, 13 insertions(+)
+ 2 files changed, 12 insertions(+)
--- a/drivers/gpu/drm/bridge/panel.c
+++ b/drivers/gpu/drm/bridge/panel.c
-@@ -258,6 +258,9 @@ struct drm_bridge *drm_panel_bridge_add_
- panel_bridge->bridge.ops = DRM_BRIDGE_OP_MODES;
- panel_bridge->bridge.type = connector_type;
+@@ -368,6 +368,8 @@ struct drm_bridge *devm_drm_panel_bridge
+ devres_free(ptr);
+ }
-+ panel_bridge->bridge.pre_enable_upstream_first =
-+ panel->prepare_upstream_first;
++ bridge->pre_enable_prev_first = panel->prepare_prev_first;
+
- drm_bridge_add(&panel_bridge->bridge);
-
- return &panel_bridge->bridge;
+ return bridge;
+ }
+ EXPORT_SYMBOL(devm_drm_panel_bridge_add_typed);
--- a/include/drm/drm_panel.h
+++ b/include/drm/drm_panel.h
@@ -196,6 +196,16 @@ struct drm_panel {
struct list_head list;
+
+ /**
-+ * @prepare_upstream_first:
++ * @prepare_prev_first:
+ *
-+ * The upstream controller should be prepared first, before the prepare
++ * The previous controller should be prepared first, before the prepare
+ * for the panel is called. This is largely required for DSI panels
+ * where the DSI host controller should be initialised to LP-11 before
+ * the panel is powered up.
+ */
-+ bool prepare_upstream_first;
++ bool prepare_prev_first;
};
void drm_panel_init(struct drm_panel *panel, struct device *dev,
--- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c
+++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c
-@@ -393,7 +393,7 @@ static const struct gpio_chip bcm2835_gp
+@@ -391,7 +391,7 @@ static const struct gpio_chip bcm2835_gp
.get = bcm2835_gpio_get,
.set = bcm2835_gpio_set,
.set_config = gpiochip_generic_config,
.ngpio = BCM2835_NUM_GPIOS,
.can_sleep = false,
.of_gpio_ranges_fallback = bcm2835_of_gpio_ranges_fallback,
-@@ -410,7 +410,7 @@ static const struct gpio_chip bcm2711_gp
+@@ -408,7 +408,7 @@ static const struct gpio_chip bcm2711_gp
.get = bcm2835_gpio_get,
.set = bcm2835_gpio_set,
.set_config = gpiochip_generic_config,
}
--- a/drivers/mmc/core/quirks.h
+++ b/drivers/mmc/core/quirks.h
-@@ -106,6 +106,14 @@ static const struct mmc_fixup __maybe_un
+@@ -129,6 +129,14 @@ static const struct mmc_fixup __maybe_un
MMC_FIXUP(CID_NAME_ANY, CID_MANFID_SANDISK_SD, 0x5344, add_quirk_sd,
MMC_QUIRK_BROKEN_SD_DISCARD),
sdhci_dumpregs(host);
--- a/include/linux/mmc/card.h
+++ b/include/linux/mmc/card.h
-@@ -295,6 +295,8 @@ struct mmc_card {
- #define MMC_QUIRK_BROKEN_HPI (1<<13) /* Disable broken HPI support */
+@@ -296,6 +296,8 @@ struct mmc_card {
#define MMC_QUIRK_BROKEN_SD_DISCARD (1<<14) /* Disable broken SD discard support */
+ #define MMC_QUIRK_BROKEN_SD_CACHE (1<<15) /* Disable broken SD cache support */
+#define MMC_QUIRK_ERASE_BROKEN (1<<31) /* Skip erase */
+
--- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c
+++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c
-@@ -1357,7 +1357,7 @@ static int bcm2835_pinctrl_probe(struct
+@@ -1355,7 +1355,7 @@ static int bcm2835_pinctrl_probe(struct
girq->default_type = IRQ_TYPE_NONE;
girq->handler = handle_level_irq;
pagelistinfo->scatterlist_mapped = 0;
@@ -468,6 +515,7 @@ free_pagelist(struct vchiq_instance *ins
- int vchiq_platform_init(struct platform_device *pdev, struct vchiq_state *state)
+ static int vchiq_platform_init(struct platform_device *pdev, struct vchiq_state *state)
{
struct device *dev = &pdev->dev;
+ struct device *dma_dev = NULL;
struct vchiq_drvdata *drvdata = platform_get_drvdata(pdev);
struct rpi_firmware *fw = drvdata->fw;
struct vchiq_slot_zero *vchiq_slot_zero;
-@@ -489,6 +537,24 @@ int vchiq_platform_init(struct platform_
+@@ -489,6 +537,24 @@ static int vchiq_platform_init(struct pl
g_cache_line_size = drvdata->cache_line_size;
g_fragments_size = 2 * g_cache_line_size;
/* Allocate space for the channels in coherent memory */
slot_mem_size = PAGE_ALIGN(TOTAL_SLOTS * VCHIQ_SLOT_SIZE);
frag_mem_size = PAGE_ALIGN(g_fragments_size * MAX_FRAGMENTS);
-@@ -501,13 +567,14 @@ int vchiq_platform_init(struct platform_
+@@ -501,13 +567,14 @@ static int vchiq_platform_init(struct pl
}
WARN_ON(((unsigned long)slot_mem & (PAGE_SIZE - 1)) != 0);
vchiq_slot_zero->platform_data[VCHIQ_PLATFORM_FRAGMENTS_COUNT_IDX] =
MAX_FRAGMENTS;
-@@ -541,7 +608,6 @@ int vchiq_platform_init(struct platform_
+@@ -541,7 +608,6 @@ static int vchiq_platform_init(struct pl
}
/* Send the base address of the slots to VideoCore */
err = rpi_firmware_property(fw, RPI_FIRMWARE_VCHIQ_INIT,
&channelbase, sizeof(channelbase));
if (err || channelbase) {
-@@ -549,6 +615,8 @@ int vchiq_platform_init(struct platform_
+@@ -549,6 +615,8 @@ static int vchiq_platform_init(struct pl
return err ? : -ENXIO;
}
pagelistinfo->dma_dir = (type == PAGELIST_WRITE) ?
DMA_TO_DEVICE : DMA_FROM_DEVICE;
pagelistinfo->num_pages = num_pages;
-@@ -616,6 +634,13 @@ int vchiq_platform_init(struct platform_
+@@ -616,6 +634,13 @@ static int vchiq_platform_init(struct pl
}
g_dma_dev = dma_dev ?: dev;
--- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c
+++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c
-@@ -928,9 +928,12 @@ static int bcm2835_pmx_free(struct pinct
+@@ -926,9 +926,12 @@ static int bcm2835_pmx_free(struct pinct
unsigned offset)
{
struct bcm2835_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev);
return 0;
}
-@@ -972,10 +975,7 @@ static void bcm2835_pmx_gpio_disable_fre
+@@ -970,10 +973,7 @@ static void bcm2835_pmx_gpio_disable_fre
struct pinctrl_gpio_range *range,
unsigned offset)
{
From: Dave Stevenson <dave.stevenson@raspberrypi.com>
Date: Thu, 31 Mar 2022 12:05:04 +0100
Subject: [PATCH] drm/panel: panel-ilitek9881c: Add
- prepare_upstream_first flag
+ prepare_prev_first flag
The panel sends MIPI DCS commands during prepare and is expecting
the bus to remain in LP-11 state in-between.
-Set the prepare_upstream_first flag so that the upstream DSI host
+Set the prepare_prev_first flag so that the upstream DSI host
is prepared / pre_enabled first, and therefore the bus is in a
defined state.
ctx->dsi = dsi;
ctx->desc = of_device_get_match_data(&dsi->dev);
-+ ctx->panel.prepare_upstream_first = true;
++ ctx->panel.prepare_prev_first = true;
drm_panel_init(&ctx->panel, &dsi->dev, &ili9881c_funcs,
DRM_MODE_CONNECTOR_DSI);
+++ /dev/null
-From 10fcafcad54e1d055b6b67881a5b52b95dbd2da3 Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil@raspberrypi.com>
-Date: Fri, 7 Oct 2022 10:38:31 +0100
-Subject: [PATCH] nvmem: Use NVMEM_DEVID_AUTO
-
-It is reasonable to declare multiple nvmem blocks. Unless a unique 'id'
-is passed in for each block there may be name clashes.
-
-Avoid this by using the magic token NVMEM_DEVID_AUTO.
-
-Fixes: 5a3fa75a4d9cb ("nvmem: Add driver to expose reserved memory as nvmem")
-
-Signed-off-by: Phil Elwell <phil@raspberrypi.com>
----
- drivers/nvmem/rmem.c | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/drivers/nvmem/rmem.c
-+++ b/drivers/nvmem/rmem.c
-@@ -71,6 +71,7 @@ static int rmem_probe(struct platform_de
- config.dev = dev;
- config.priv = priv;
- config.name = "rmem";
-+ config.id = NVMEM_DEVID_AUTO;
- config.size = mem->size;
- config.reg_read = rmem_read;
-
@@ -4568,7 +4569,9 @@ static int hci_dev_setup_sync(struct hci
if (!ret) {
- if (test_bit(HCI_QUIRK_USE_BDADDR_PROPERTY, &hdev->quirks)) {
-- if (!bacmp(&hdev->public_addr, BDADDR_ANY))
-+ if (!bacmp(&hdev->public_addr, BDADDR_ANY) &&
-+ (invalid_bdaddr ||
-+ !fwnode_property_present(fwnode, "fallback-bd-address")))
- hci_dev_get_bd_addr_from_property(hdev);
+ if (test_bit(HCI_QUIRK_USE_BDADDR_PROPERTY, &hdev->quirks) &&
+- !bacmp(&hdev->public_addr, BDADDR_ANY))
++ !bacmp(&hdev->public_addr, BDADDR_ANY) &&
++ (invalid_bdaddr ||
++ !fwnode_property_present(fwnode, "fallback-bd-address")))
+ hci_dev_get_bd_addr_from_property(hdev);
- if (bacmp(&hdev->public_addr, BDADDR_ANY) &&
+ if ((invalid_bdaddr ||
--- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c
+++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c
-@@ -422,15 +422,32 @@ static void bcm2835_gpio_irq_handle_bank
+@@ -420,15 +420,32 @@ static void bcm2835_gpio_irq_handle_bank
unsigned long events;
unsigned offset;
unsigned gpio;
}
static void bcm2835_gpio_irq_handler(struct irq_desc *desc)
-@@ -670,11 +687,7 @@ static int bcm2835_gpio_irq_set_type(str
+@@ -668,11 +685,7 @@ static int bcm2835_gpio_irq_set_type(str
static void bcm2835_gpio_irq_ack(struct irq_data *data)
{
+++ /dev/null
-From 085679b15b5af65f9610f619afde41da0f966194 Mon Sep 17 00:00:00 2001
-From: Lukas Bulwahn <lukas.bulwahn@gmail.com>
-Date: Wed, 16 Nov 2022 13:49:32 +0100
-Subject: [PATCH] mtd: parsers: refer to ARCH_BCMBCA instead of ARCH_BCM4908
-
-Commit dd5c672d7ca9 ("arm64: bcmbca: Merge ARCH_BCM4908 to ARCH_BCMBCA")
-removes config ARCH_BCM4908 as config ARCH_BCMBCA has the same intent.
-
-Probably due to concurrent development, commit 002181f5b150 ("mtd: parsers:
-add Broadcom's U-Boot parser") introduces 'Broadcom's U-Boot partition
-parser' that depends on ARCH_BCM4908, but this use was not visible during
-the config refactoring from the commit above. Hence, these two changes
-create a reference to a non-existing config symbol.
-
-Adjust the MTD_BRCM_U_BOOT definition to refer to ARCH_BCMBCA instead of
-ARCH_BCM4908 to remove the reference to the non-existing config symbol
-ARCH_BCM4908.
-
-Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
-Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
-Link: https://lore.kernel.org/linux-mtd/20221116124932.4748-1-lukas.bulwahn@gmail.com
----
- drivers/mtd/parsers/Kconfig | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/mtd/parsers/Kconfig
-+++ b/drivers/mtd/parsers/Kconfig
-@@ -22,7 +22,7 @@ config MTD_BCM63XX_PARTS
-
- config MTD_BRCM_U_BOOT
- tristate "Broadcom's U-Boot partition parser"
-- depends on ARCH_BCM4908 || COMPILE_TEST
-+ depends on ARCH_BCMBCA || COMPILE_TEST
- help
- Broadcom uses a custom way of storing U-Boot environment variables.
- They are placed inside U-Boot partition itself at unspecified offset.
};
};
-@@ -558,24 +390,4 @@
+@@ -557,24 +389,4 @@
};
};
};
+++ /dev/null
-From d3c8e2c5757153bbfad70019ec1decbca86f3def Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal@milecki.pl>
-Date: Wed, 3 May 2023 14:28:30 +0200
-Subject: [PATCH] ARM: dts: BCM5301X: Drop "clock-names" from the SPI node
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-There is no such property in the SPI controller binding documentation.
-Also Linux driver doesn't look for it.
-
-This fixes:
-arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dtb: spi@18029200: Unevaluated properties are not allowed ('clock-names' was unexpected)
- From schema: Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.yaml
-
-Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
-Link: https://lore.kernel.org/r/20230503122830.3200-1-zajec5@gmail.com
-Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
----
- arch/arm/boot/dts/bcm5301x.dtsi | 1 -
- 1 file changed, 1 deletion(-)
-
---- a/arch/arm/boot/dts/bcm5301x.dtsi
-+++ b/arch/arm/boot/dts/bcm5301x.dtsi
-@@ -335,7 +335,6 @@
- "spi_lr_session_done",
- "spi_lr_overread";
- clocks = <&iprocmed>;
-- clock-names = "iprocmed";
- num-cs = <2>;
- #address-cells = <1>;
- #size-cells = <0>;
+++ /dev/null
-From fd274b733bfdde3ca72f0fa2a37f032f3a8c402c Mon Sep 17 00:00:00 2001
-From: Christian Lamparter <chunkeey@gmail.com>
-Date: Thu, 8 Jun 2023 17:36:29 +0200
-Subject: [PATCH] ARM: dts: BCM5301X: fix duplex-full => full-duplex
-
-this typo was found by the dtbs_check
-| ports:port@5:fixed-link: 'oneOf' conditional failed,
-| {'speed': [[1000]], 'duplex-full': True} is not of type 'array'
-| 'duplex-full' does not match any of the regexes: 'pinctrl-[0-]..."
-
-this should have been full-duplex;
-
-Fixes: 935327a73553 ("ARM: dts: BCM5301X: Add DT for Meraki MR26")
-Fixes: ec88a9c344d9 ("ARM: BCM5301X: Add DT for Meraki MR32")
-Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
-Link: https://lore.kernel.org/r/50522f45566951a9eabd22820647924cc6b4a264.1686238550.git.chunkeey@gmail.com
-Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
----
- arch/arm/boot/dts/bcm53015-meraki-mr26.dts | 2 +-
- arch/arm/boot/dts/bcm53016-meraki-mr32.dts | 2 +-
- 2 files changed, 2 insertions(+), 2 deletions(-)
-
---- a/arch/arm/boot/dts/bcm53015-meraki-mr26.dts
-+++ b/arch/arm/boot/dts/bcm53015-meraki-mr26.dts
-@@ -121,7 +121,7 @@
-
- fixed-link {
- speed = <1000>;
-- duplex-full;
-+ full-duplex;
- };
- };
- };
---- a/arch/arm/boot/dts/bcm53016-meraki-mr32.dts
-+++ b/arch/arm/boot/dts/bcm53016-meraki-mr32.dts
-@@ -182,7 +182,7 @@
-
- fixed-link {
- speed = <1000>;
-- duplex-full;
-+ full-duplex;
- };
- };
- };
mark_page_accessed(page);
}
rss[mm_counter(page)]--;
-@@ -5182,8 +5181,8 @@ static inline void mm_account_fault(stru
+@@ -5189,8 +5188,8 @@ static inline void mm_account_fault(stru
#ifdef CONFIG_LRU_GEN
static void lru_gen_enter_fault(struct vm_area_struct *vma)
{
+++ /dev/null
-From cee4bd16c3195a701be683f7da9e88c6e11acb73 Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth@gmail.com>
-Date: Wed, 19 Apr 2023 23:07:39 +0200
-Subject: [PATCH 1/5] leds: trigger: netdev: Recheck NETDEV_LED_MODE_LINKUP on
- dev rename
-
-Dev can be renamed also while up for supported device. We currently
-wrongly clear the NETDEV_LED_MODE_LINKUP flag on NETDEV_CHANGENAME
-event.
-
-Fix this by rechecking if the carrier is ok on NETDEV_CHANGENAME and
-correctly set the NETDEV_LED_MODE_LINKUP bit.
-
-Fixes: 5f820ed52371 ("leds: trigger: netdev: fix handling on interface rename")
-Cc: stable@vger.kernel.org # v5.5+
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
-Reviewed-by: Andrew Lunn <andrew@lunn.ch>
-Signed-off-by: Lee Jones <lee@kernel.org>
-Link: https://lore.kernel.org/r/20230419210743.3594-2-ansuelsmth@gmail.com
----
- drivers/leds/trigger/ledtrig-netdev.c | 3 +++
- 1 file changed, 3 insertions(+)
-
---- a/drivers/leds/trigger/ledtrig-netdev.c
-+++ b/drivers/leds/trigger/ledtrig-netdev.c
-@@ -318,6 +318,9 @@ static int netdev_trig_notify(struct not
- clear_bit(NETDEV_LED_MODE_LINKUP, &trigger_data->mode);
- switch (evt) {
- case NETDEV_CHANGENAME:
-+ if (netif_carrier_ok(dev))
-+ set_bit(NETDEV_LED_MODE_LINKUP, &trigger_data->mode);
-+ fallthrough;
- case NETDEV_REGISTER:
- if (trigger_data->net_dev)
- dev_put(trigger_data->net_dev);
--- a/scripts/mod/modpost.c
+++ b/scripts/mod/modpost.c
-@@ -1817,7 +1817,9 @@ static void read_symbols(const char *mod
+@@ -1781,7 +1781,9 @@ static void read_symbols(const char *mod
symname = remove_dot(info.strtab + sym->st_name);
handle_symbol(mod, &info, sym, symname);
}
for (sym = info.symtab_start; sym < info.symtab_stop; sym++) {
-@@ -1980,8 +1982,10 @@ static void add_header(struct buffer *b,
+@@ -1944,8 +1946,10 @@ static void add_header(struct buffer *b,
buf_printf(b, "BUILD_SALT;\n");
buf_printf(b, "BUILD_LTO_INFO;\n");
buf_printf(b, "\n");
buf_printf(b, "\n");
buf_printf(b, "__visible struct module __this_module\n");
buf_printf(b, "__section(\".gnu.linkonce.this_module\") = {\n");
-@@ -1995,8 +1999,10 @@ static void add_header(struct buffer *b,
+@@ -1959,8 +1963,10 @@ static void add_header(struct buffer *b,
buf_printf(b, "\t.arch = MODULE_ARCH_INIT,\n");
buf_printf(b, "};\n");
buf_printf(b,
"\n"
-@@ -2004,8 +2010,10 @@ static void add_header(struct buffer *b,
+@@ -1968,8 +1974,10 @@ static void add_header(struct buffer *b,
"MODULE_INFO(retpoline, \"Y\");\n"
"#endif\n");
if (strstarts(mod->name, "tools/testing"))
buf_printf(b, "\nMODULE_INFO(test, \"Y\");\n");
-@@ -2101,11 +2109,13 @@ static void add_depends(struct buffer *b
+@@ -2065,11 +2073,13 @@ static void add_depends(struct buffer *b
static void add_srcversion(struct buffer *b, struct module *mod)
{
}
static void write_buf(struct buffer *b, const char *fname)
-@@ -2191,7 +2201,9 @@ static void write_mod_c_file(struct modu
+@@ -2155,7 +2165,9 @@ static void write_mod_c_file(struct modu
add_exported_symbols(&buf, mod);
add_versions(&buf, mod);
add_depends(&buf, mod);
#define QUECTEL_VENDOR_ID 0x2c7c
/* These Quectel products use Quectel's vendor ID */
-@@ -1173,6 +1175,11 @@ static const struct usb_device_id option
+@@ -1177,6 +1179,11 @@ static const struct usb_device_id option
.driver_info = ZLP },
{ USB_DEVICE(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_BG96),
.driver_info = RSVD(4) },
--- a/net/core/sock.c
+++ b/net/core/sock.c
-@@ -4082,6 +4082,8 @@ static __net_initdata struct pernet_oper
+@@ -4093,6 +4093,8 @@ static __net_initdata struct pernet_oper
static int __init proto_init(void)
{
+++ /dev/null
-From eee53f6eb7561f516b9c4bac829ce31c48096130 Mon Sep 17 00:00:00 2001
-From: Fabian Frederick <fabf@skynet.be>
-Date: Tue, 9 May 2017 22:30:03 +0200
-Subject: [PATCH] jffs2: reduce stack usage in jffs2_build_xattr_subsystem()
-
-Use kcalloc() for allocation/flush of 128 pointers table to
-reduce stack usage.
-
-Function now returns -ENOMEM or 0 on success.
-
-stackusage
-Before:
-./fs/jffs2/xattr.c:775 jffs2_build_xattr_subsystem 1208
-dynamic,bounded
-
-After:
-./fs/jffs2/xattr.c:775 jffs2_build_xattr_subsystem 192
-dynamic,bounded
-
-Also update definition when CONFIG_JFFS2_FS_XATTR is not enabled
-
-Tested with an MTD mount point and some user set/getfattr.
-
-Many current target on OpenWRT also suffer from a compilation warning
-(that become an error with CONFIG_WERROR) with the following output:
-
-fs/jffs2/xattr.c: In function 'jffs2_build_xattr_subsystem':
-fs/jffs2/xattr.c:887:1: error: the frame size of 1088 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
- 887 | }
- | ^
-
-Using dynamic allocation fix this compilation warning.
-
-Fixes: c9f700f840bd ("[JFFS2][XATTR] using 'delete marker' for xdatum/xref deletion")
-Reported-by: Tim Gardner <tim.gardner@canonical.com>
-Reported-by: kernel test robot <lkp@intel.com>
-Reported-by: Ron Economos <re@w6rz.net>
-Reported-by: Nathan Chancellor <nathan@kernel.org>
-Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
-Signed-off-by: Fabian Frederick <fabf@skynet.be>
-Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
-Cc: stable@vger.kernel.org
----
- fs/jffs2/build.c | 5 ++++-
- fs/jffs2/xattr.c | 13 +++++++++----
- fs/jffs2/xattr.h | 4 ++--
- 3 files changed, 15 insertions(+), 7 deletions(-)
-
---- a/fs/jffs2/build.c
-+++ b/fs/jffs2/build.c
-@@ -211,7 +211,10 @@ static int jffs2_build_filesystem(struct
- ic->scan_dents = NULL;
- cond_resched();
- }
-- jffs2_build_xattr_subsystem(c);
-+ ret = jffs2_build_xattr_subsystem(c);
-+ if (ret)
-+ goto exit;
-+
- c->flags &= ~JFFS2_SB_FLAG_BUILDING;
-
- dbg_fsbuild("FS build complete\n");
---- a/fs/jffs2/xattr.c
-+++ b/fs/jffs2/xattr.c
-@@ -772,10 +772,10 @@ void jffs2_clear_xattr_subsystem(struct
- }
-
- #define XREF_TMPHASH_SIZE (128)
--void jffs2_build_xattr_subsystem(struct jffs2_sb_info *c)
-+int jffs2_build_xattr_subsystem(struct jffs2_sb_info *c)
- {
- struct jffs2_xattr_ref *ref, *_ref;
-- struct jffs2_xattr_ref *xref_tmphash[XREF_TMPHASH_SIZE];
-+ struct jffs2_xattr_ref **xref_tmphash;
- struct jffs2_xattr_datum *xd, *_xd;
- struct jffs2_inode_cache *ic;
- struct jffs2_raw_node_ref *raw;
-@@ -784,9 +784,12 @@ void jffs2_build_xattr_subsystem(struct
-
- BUG_ON(!(c->flags & JFFS2_SB_FLAG_BUILDING));
-
-+ xref_tmphash = kcalloc(XREF_TMPHASH_SIZE,
-+ sizeof(struct jffs2_xattr_ref *), GFP_KERNEL);
-+ if (!xref_tmphash)
-+ return -ENOMEM;
-+
- /* Phase.1 : Merge same xref */
-- for (i=0; i < XREF_TMPHASH_SIZE; i++)
-- xref_tmphash[i] = NULL;
- for (ref=c->xref_temp; ref; ref=_ref) {
- struct jffs2_xattr_ref *tmp;
-
-@@ -884,6 +887,8 @@ void jffs2_build_xattr_subsystem(struct
- "%u of xref (%u dead, %u orphan) found.\n",
- xdatum_count, xdatum_unchecked_count, xdatum_orphan_count,
- xref_count, xref_dead_count, xref_orphan_count);
-+ kfree(xref_tmphash);
-+ return 0;
- }
-
- struct jffs2_xattr_datum *jffs2_setup_xattr_datum(struct jffs2_sb_info *c,
---- a/fs/jffs2/xattr.h
-+++ b/fs/jffs2/xattr.h
-@@ -71,7 +71,7 @@ static inline int is_xattr_ref_dead(stru
- #ifdef CONFIG_JFFS2_FS_XATTR
-
- extern void jffs2_init_xattr_subsystem(struct jffs2_sb_info *c);
--extern void jffs2_build_xattr_subsystem(struct jffs2_sb_info *c);
-+extern int jffs2_build_xattr_subsystem(struct jffs2_sb_info *c);
- extern void jffs2_clear_xattr_subsystem(struct jffs2_sb_info *c);
-
- extern struct jffs2_xattr_datum *jffs2_setup_xattr_datum(struct jffs2_sb_info *c,
-@@ -103,7 +103,7 @@ extern ssize_t jffs2_listxattr(struct de
- #else
-
- #define jffs2_init_xattr_subsystem(c)
--#define jffs2_build_xattr_subsystem(c)
-+#define jffs2_build_xattr_subsystem(c) (0)
- #define jffs2_clear_xattr_subsystem(c)
-
- #define jffs2_xattr_do_crccheck_inode(c, ic)
struct rtnl_link {
rtnl_doit_func doit;
-@@ -4817,7 +4817,9 @@ int ndo_dflt_bridge_getlink(struct sk_bu
+@@ -4823,7 +4823,9 @@ int ndo_dflt_bridge_getlink(struct sk_bu
brport_nla_put_flag(skb, flags, mask,
IFLA_BRPORT_MCAST_FLOOD, BR_MCAST_FLOOD) ||
brport_nla_put_flag(skb, flags, mask,
--- a/drivers/cpufreq/mediatek-cpufreq.c
+++ b/drivers/cpufreq/mediatek-cpufreq.c
-@@ -702,6 +702,15 @@ static const struct mtk_cpufreq_platform
+@@ -709,6 +709,15 @@ static const struct mtk_cpufreq_platform
.ccifreq_supported = false,
};
static const struct mtk_cpufreq_platform_data mt8183_platform_data = {
.min_volt_shift = 100000,
.max_volt_shift = 200000,
-@@ -735,6 +744,7 @@ static const struct of_device_id mtk_cpu
+@@ -742,6 +751,7 @@ static const struct of_device_id mtk_cpu
{ .compatible = "mediatek,mt2712", .data = &mt2701_platform_data },
{ .compatible = "mediatek,mt7622", .data = &mt7622_platform_data },
- { .compatible = "mediatek,mt7623", .data = &mt7622_platform_data },
+ { .compatible = "mediatek,mt7623", .data = &mt7623_platform_data },
+ { .compatible = "mediatek,mt7988", .data = &mt7988_platform_data },
{ .compatible = "mediatek,mt8167", .data = &mt8516_platform_data },
{ .compatible = "mediatek,mt817x", .data = &mt2701_platform_data },
+++ /dev/null
-From e7697814c142c99f470c3458d49e41b25a575f23 Mon Sep 17 00:00:00 2001
-From: Daniel Golle <daniel@makrotopia.org>
-Date: Fri, 26 May 2023 10:31:40 +0100
-Subject: [PATCH] cpufreq: mediatek: correct voltages for MT7622 and MT7623
-
-The MT6380 regulator typically used together with MT7622 does not
-support the current maximum processor and SRAM voltage in the cpufreq
-driver (1360000uV).
-For MT7622 limit processor and SRAM supply voltages to 1350000uV to
-avoid having the tracking algorithm request unsupported voltages from
-the regulator.
-
-On MT7623 there is no separate SRAM supply and the maximum voltage used
-is 1300000uV. Create dedicated platform data for MT7623 to cover that
-case as well.
-
-Fixes: 0883426fd07e3 ("cpufreq: mediatek: Raise proc and sram max voltage for MT7622/7623")
-Suggested-by: Jia-wei Chang <Jia-wei.Chang@mediatek.com>
-Signed-off-by: Daniel Golle <daniel@makrotopia.org>
----
- drivers/cpufreq/mediatek-cpufreq.c | 13 ++++++++++---
- 1 file changed, 10 insertions(+), 3 deletions(-)
-
---- a/drivers/cpufreq/mediatek-cpufreq.c
-+++ b/drivers/cpufreq/mediatek-cpufreq.c
-@@ -696,9 +696,16 @@ static const struct mtk_cpufreq_platform
- static const struct mtk_cpufreq_platform_data mt7622_platform_data = {
- .min_volt_shift = 100000,
- .max_volt_shift = 200000,
-- .proc_max_volt = 1360000,
-+ .proc_max_volt = 1350000,
- .sram_min_volt = 0,
-- .sram_max_volt = 1360000,
-+ .sram_max_volt = 1350000,
-+ .ccifreq_supported = false,
-+};
-+
-+static const struct mtk_cpufreq_platform_data mt7623_platform_data = {
-+ .min_volt_shift = 100000,
-+ .max_volt_shift = 200000,
-+ .proc_max_volt = 1300000,
- .ccifreq_supported = false,
- };
-
-@@ -743,7 +750,7 @@ static const struct of_device_id mtk_cpu
- { .compatible = "mediatek,mt2701", .data = &mt2701_platform_data },
- { .compatible = "mediatek,mt2712", .data = &mt2701_platform_data },
- { .compatible = "mediatek,mt7622", .data = &mt7622_platform_data },
-- { .compatible = "mediatek,mt7623", .data = &mt7622_platform_data },
-+ { .compatible = "mediatek,mt7623", .data = &mt7623_platform_data },
- { .compatible = "mediatek,mt7988", .data = &mt7988_platform_data },
- { .compatible = "mediatek,mt8167", .data = &mt8516_platform_data },
- { .compatible = "mediatek,mt817x", .data = &mt2701_platform_data },
+++ /dev/null
-From 813ba3e427671ba3ff35c825087b03f0ad91cf02 Mon Sep 17 00:00:00 2001
-From: Robert Marko <robimarko@gmail.com>
-Date: Mon, 7 Nov 2022 14:28:59 +0100
-Subject: [PATCH] clk: qcom: reset: support resetting multiple bits
-
-This patch adds the support for giving the complete bitmask
-in reset structure and reset operation will use this bitmask
-for all reset operations.
-
-Currently, reset structure only takes a single bit for each reset
-and then calculates the bitmask by using the BIT() macro.
-
-However, this is not sufficient anymore for newer SoC-s like IPQ8074,
-IPQ6018 and more, since their networking resets require multiple bits
-to be asserted in order to properly reset the HW block completely.
-
-So, in order to allow asserting multiple bits add "bitmask" field to
-qcom_reset_map, and then use that bitmask value if its populated in the
-driver, if its not populated, then we just default to existing behaviour
-and calculate the bitmask on the fly.
-
-Signed-off-by: Robert Marko <robimarko@gmail.com>
-Signed-off-by: Bjorn Andersson <andersson@kernel.org>
-Link: https://lore.kernel.org/r/20221107132901.489240-1-robimarko@gmail.com
----
- drivers/clk/qcom/reset.c | 4 ++--
- drivers/clk/qcom/reset.h | 1 +
- 2 files changed, 3 insertions(+), 2 deletions(-)
-
---- a/drivers/clk/qcom/reset.c
-+++ b/drivers/clk/qcom/reset.c
-@@ -30,7 +30,7 @@ qcom_reset_assert(struct reset_controlle
-
- rst = to_qcom_reset_controller(rcdev);
- map = &rst->reset_map[id];
-- mask = BIT(map->bit);
-+ mask = map->bitmask ? map->bitmask : BIT(map->bit);
-
- return regmap_update_bits(rst->regmap, map->reg, mask, mask);
- }
-@@ -44,7 +44,7 @@ qcom_reset_deassert(struct reset_control
-
- rst = to_qcom_reset_controller(rcdev);
- map = &rst->reset_map[id];
-- mask = BIT(map->bit);
-+ mask = map->bitmask ? map->bitmask : BIT(map->bit);
-
- return regmap_update_bits(rst->regmap, map->reg, mask, 0);
- }
---- a/drivers/clk/qcom/reset.h
-+++ b/drivers/clk/qcom/reset.h
-@@ -12,6 +12,7 @@ struct qcom_reset_map {
- unsigned int reg;
- u8 bit;
- u8 udelay;
-+ u32 bitmask;
- };
-
- struct regmap;
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
-@@ -1745,6 +1745,7 @@ static const struct of_device_id qcom_pc
+@@ -1762,6 +1762,7 @@ static const struct of_device_id qcom_pc
{ .compatible = "qcom,pcie-ipq8064", .data = &cfg_2_1_0 },
{ .compatible = "qcom,pcie-ipq8064-v2", .data = &cfg_2_1_0 },
{ .compatible = "qcom,pcie-ipq8074", .data = &cfg_2_3_3 },
--- a/drivers/mmc/core/quirks.h
+++ b/drivers/mmc/core/quirks.h
-@@ -101,6 +101,13 @@ static const struct mmc_fixup __maybe_un
+@@ -124,6 +124,13 @@ static const struct mmc_fixup __maybe_un
MMC_QUIRK_TRIM_BROKEN),
/*
--- a/drivers/mmc/core/quirks.h
+++ b/drivers/mmc/core/quirks.h
-@@ -108,6 +108,13 @@ static const struct mmc_fixup __maybe_un
+@@ -131,6 +131,13 @@ static const struct mmc_fixup __maybe_un
MMC_QUIRK_TRIM_BROKEN),
/*
projects / openwrt / openwrt.git / commitdiff