+++ /dev/null
-#
-# Copyright (C) 2008-2015 OpenWrt.org
-#
-# This is free software, licensed under the GNU General Public License v2.
-# See /LICENSE for more information.
-#
-include $(TOPDIR)/rules.mk
-
-ARCH:=arm
-BOARD:=orion
-BOARDNAME:=Marvell Orion
-FEATURES:=broken rtc
-SUBTARGETS:=generic harddisk
-MAINTAINER:=Imre Kaloz <kaloz@openwrt.org>
-
-KERNEL_PATCHVER:=4.14
-
-include $(INCLUDE_DIR)/target.mk
-
-KERNELNAME:=zImage
-
-DEFAULT_PACKAGES += kmod-ath9k wpad-basic kmod-rtc-isl1208 uboot-envtools
-
-$(eval $(call BuildTarget))
+++ /dev/null
-#!/bin/sh
-
-. /lib/functions/uci-defaults.sh
-
-board_config_update
-
-if grep -q lan1 /proc/net/dev; then
- ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
-else
- ucidef_set_interface_lan "eth0"
-fi
-
-board_config_flush
-
-exit 0
+++ /dev/null
-#!/bin/sh
-#
-# Copyright (C) 2009-2010 OpenWrt.org
-#
-# This is free software, licensed under the GNU General Public License v2.
-# See /LICENSE for more information.
-#
-
-usb_led=''
-usb_device=''
-
-led_set_attr() {
- [ -f "/sys/class/leds/$1/$2" ] && echo "$3" > "/sys/class/leds/$1/$2"
-}
-
-usb_led_set_timer() {
- led_set_attr "${usb_led}" 'trigger' 'timer'
- led_set_attr "${usb_led}" 'delay_on' "$1"
- led_set_attr "${usb_led}" 'delay_off' "$2"
-}
-
-usb_led_on() {
- led_set_attr "${usb_led}" 'trigger' 'none'
- led_set_attr "${usb_led}" 'brightness' 255
-}
-
-usb_led_off() {
- led_set_attr "${usb_led}" 'trigger' 'none'
- led_set_attr "${usb_led}" 'brightness' 0
-}
-
-get_usb_led() {
- . /lib/functions.sh
-
- case "$(board_name)" in
- 'Linksys WRT350N v2')
- usb_led='wrt350nv2:green:usb'
- usb_device='1-1:1.0'
- ;;
- esac;
-}
-
-get_usb_led
-
-case "${ACTION}" in
- add)
- # update LEDs
- [ "${usb_device}" = "${DEVICENAME}" ] && usb_led_on
- ;;
- remove)
- # update LEDs
- [ "${usb_device}" = "${DEVICENAME}" ] && usb_led_off
- ;;
-esac
+++ /dev/null
-#!/bin/sh
-
-do_sysinfo_orion() {
- local name="$(sed -n /Hardware/s/.*:.//p /proc/cpuinfo)"
- [ -z "$name" ] && name="unknown"
-
- [ -e "/tmp/sysinfo/" ] || mkdir -p "/tmp/sysinfo/"
- echo "$name" > /tmp/sysinfo/board_name
- echo "unknown" > /tmp/sysinfo/model
-}
-
-boot_hook_add preinit_main do_sysinfo_orion
+++ /dev/null
-CONFIG_ALIGNMENT_TRAP=y
-CONFIG_ARCH_CLOCKSOURCE_DATA=y
-CONFIG_ARCH_HAS_DEBUG_VIRTUAL=y
-CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
-CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
-CONFIG_ARCH_HAS_SET_MEMORY=y
-CONFIG_ARCH_HAS_SG_CHAIN=y
-CONFIG_ARCH_HAS_STRICT_KERNEL_RWX=y
-CONFIG_ARCH_HAS_STRICT_MODULE_RWX=y
-CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
-CONFIG_ARCH_HIBERNATION_POSSIBLE=y
-CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
-CONFIG_ARCH_MULTIPLATFORM=y
-CONFIG_ARCH_MULTI_CPU_AUTO=y
-# CONFIG_ARCH_MULTI_V4 is not set
-# CONFIG_ARCH_MULTI_V4T is not set
-CONFIG_ARCH_MULTI_V4_V5=y
-CONFIG_ARCH_MULTI_V5=y
-CONFIG_ARCH_NR_GPIO=0
-CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y
-# CONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT is not set
-CONFIG_ARCH_ORION5X=y
-# CONFIG_ARCH_ORION5X_DT is not set
-# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
-# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
-CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
-CONFIG_ARCH_SUPPORTS_UPROBES=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARCH_USE_BUILTIN_BSWAP=y
-CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
-CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
-CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
-CONFIG_ARM=y
-# CONFIG_ARM_CPU_SUSPEND is not set
-CONFIG_ARM_HAS_SG_CHAIN=y
-CONFIG_ARM_L1_CACHE_SHIFT=5
-CONFIG_ARM_PATCH_PHYS_VIRT=y
-# CONFIG_ARM_THUMB is not set
-CONFIG_ASYNC_TX_ENABLE_CHANNEL_SWITCH=y
-CONFIG_ATAGS=y
-CONFIG_AUTO_ZRELADDR=y
-CONFIG_BLK_MQ_PCI=y
-# CONFIG_CACHE_L2X0 is not set
-CONFIG_CLKDEV_LOOKUP=y
-CONFIG_CLKSRC_MMIO=y
-CONFIG_CLONE_BACKWARDS=y
-CONFIG_CMDLINE="rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 earlyprintk"
-CONFIG_CMDLINE_FORCE=y
-CONFIG_COMMON_CLK=y
-CONFIG_CPU_32v5=y
-CONFIG_CPU_ABRT_EV5T=y
-CONFIG_CPU_CACHE_VIVT=y
-CONFIG_CPU_COPY_FEROCEON=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-CONFIG_CPU_FEROCEON=y
-CONFIG_CPU_FEROCEON_OLD_ID=y
-# CONFIG_CPU_ICACHE_DISABLE is not set
-CONFIG_CPU_PABRT_LEGACY=y
-CONFIG_CPU_THUMB_CAPABLE=y
-CONFIG_CPU_TLB_FEROCEON=y
-CONFIG_CPU_USE_DOMAINS=y
-CONFIG_CRYPTO_DES=y
-CONFIG_CRYPTO_DEV_MARVELL_CESA=y
-CONFIG_CRYPTO_HASH=y
-CONFIG_CRYPTO_HASH2=y
-CONFIG_CRYPTO_HW=y
-CONFIG_CRYPTO_RNG2=y
-CONFIG_CRYPTO_WORKQUEUE=y
-CONFIG_DEBUG_LL=y
-CONFIG_DEBUG_LL_INCLUDE="debug/8250.S"
-CONFIG_DEBUG_LL_UART_8250=y
-# CONFIG_DEBUG_MVEBU_UART0_ALTERNATE is not set
-# CONFIG_DEBUG_UART_8250 is not set
-# CONFIG_DEBUG_UART_8250_FLOW_CONTROL is not set
-CONFIG_DEBUG_UART_8250_SHIFT=2
-# CONFIG_DEBUG_UART_8250_WORD is not set
-CONFIG_DEBUG_UART_PHYS=0xf1012000
-CONFIG_DEBUG_UART_VIRT=0xfe012000
-CONFIG_DEBUG_UNCOMPRESS=y
-# CONFIG_DEBUG_USER is not set
-CONFIG_DMADEVICES=y
-CONFIG_DMA_ENGINE=y
-CONFIG_DMA_ENGINE_RAID=y
-CONFIG_DMA_OF=y
-CONFIG_DNOTIFY=y
-CONFIG_DTC=y
-CONFIG_EARLY_PRINTK=y
-CONFIG_EDAC_ATOMIC_SCRUB=y
-CONFIG_EDAC_SUPPORT=y
-CONFIG_FIXED_PHY=y
-CONFIG_FIX_EARLYCON_MEM=y
-CONFIG_FRAME_POINTER=y
-CONFIG_GENERIC_ALLOCATOR=y
-CONFIG_GENERIC_ATOMIC64=y
-CONFIG_GENERIC_BUG=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CPU_AUTOPROBE=y
-CONFIG_GENERIC_EARLY_IOREMAP=y
-CONFIG_GENERIC_IDLE_POLL_SETUP=y
-CONFIG_GENERIC_IO=y
-CONFIG_GENERIC_IRQ_CHIP=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GENERIC_SCHED_CLOCK=y
-CONFIG_GENERIC_SMP_IDLE_THREAD=y
-CONFIG_GENERIC_STRNCPY_FROM_USER=y
-CONFIG_GENERIC_STRNLEN_USER=y
-CONFIG_GPIOLIB=y
-CONFIG_GPIO_MVEBU=y
-CONFIG_GPIO_SYSFS=y
-# CONFIG_GRO_CELLS is not set
-CONFIG_HANDLE_DOMAIN_IRQ=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT_MAP=y
-# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
-CONFIG_HAVE_ARCH_AUDITSYSCALL=y
-# CONFIG_HAVE_ARCH_BITREVERSE is not set
-CONFIG_HAVE_ARCH_JUMP_LABEL=y
-CONFIG_HAVE_ARCH_KGDB=y
-CONFIG_HAVE_ARCH_PFN_VALID=y
-CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
-CONFIG_HAVE_ARCH_TRACEHOOK=y
-# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
-CONFIG_HAVE_CC_STACKPROTECTOR=y
-CONFIG_HAVE_CLK=y
-CONFIG_HAVE_CLK_PREPARE=y
-CONFIG_HAVE_CONTEXT_TRACKING=y
-CONFIG_HAVE_C_RECORDMCOUNT=y
-CONFIG_HAVE_DEBUG_KMEMLEAK=y
-CONFIG_HAVE_DMA_API_DEBUG=y
-CONFIG_HAVE_DMA_CONTIGUOUS=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-CONFIG_HAVE_DYNAMIC_FTRACE_WITH_REGS=y
-CONFIG_HAVE_EBPF_JIT=y
-CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACER=y
-CONFIG_HAVE_GENERIC_DMA_COHERENT=y
-CONFIG_HAVE_IDE=y
-CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
-CONFIG_HAVE_MEMBLOCK=y
-CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
-CONFIG_HAVE_NET_DSA=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HAVE_OPTPROBES=y
-CONFIG_HAVE_PERF_EVENTS=y
-CONFIG_HAVE_PERF_REGS=y
-CONFIG_HAVE_PERF_USER_STACK_DUMP=y
-CONFIG_HAVE_PROC_CPU=y
-CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
-CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
-CONFIG_HAVE_UID16=y
-CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
-CONFIG_HZ_FIXED=0
-CONFIG_HZ_PERIODIC=y
-CONFIG_I2C=y
-CONFIG_I2C_BOARDINFO=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_MV64XXX=y
-# CONFIG_INITRAMFS_FORCE is not set
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_IOMMU_HELPER=y
-CONFIG_IRQCHIP=y
-CONFIG_IRQ_DOMAIN=y
-CONFIG_IRQ_FORCED_THREADING=y
-CONFIG_IRQ_WORK=y
-CONFIG_LEDS_GPIO=y
-CONFIG_LIBFDT=y
-# CONFIG_MACH_D2NET_DT is not set
-# CONFIG_MACH_DB88F5281 is not set
-# CONFIG_MACH_DNS323 is not set
-# CONFIG_MACH_DT2 is not set
-# CONFIG_MACH_KUROBOX_PRO is not set
-# CONFIG_MACH_LINKSTATION_LS_HGL is not set
-# CONFIG_MACH_LINKSTATION_MINI is not set
-# CONFIG_MACH_LINKSTATION_PRO is not set
-# CONFIG_MACH_MSS2_DT is not set
-# CONFIG_MACH_MV2120 is not set
-# CONFIG_MACH_NET2BIG is not set
-# CONFIG_MACH_RD88F5181L_FXO is not set
-# CONFIG_MACH_RD88F5181L_GE is not set
-# CONFIG_MACH_RD88F5182 is not set
-# CONFIG_MACH_RD88F5182_DT is not set
-# CONFIG_MACH_RD88F6183AP_GE is not set
-CONFIG_MACH_TERASTATION_PRO2=y
-# CONFIG_MACH_TS209 is not set
-# CONFIG_MACH_TS409 is not set
-# CONFIG_MACH_TS78XX is not set
-CONFIG_MACH_WN802T=y
-CONFIG_MACH_WNR854T=y
-CONFIG_MACH_WRT350N_V2=y
-CONFIG_MDIO_BUS=y
-CONFIG_MDIO_DEVICE=y
-CONFIG_MIGHT_HAVE_PCI=y
-CONFIG_MIGRATION=y
-CONFIG_MMC=y
-CONFIG_MMC_MVSDIO=y
-# CONFIG_MMC_TIFM_SD is not set
-CONFIG_MODULES_USE_ELF_REL=y
-CONFIG_MTD_PHYSMAP=y
-CONFIG_MULTI_IRQ_HANDLER=y
-CONFIG_MV643XX_ETH=y
-CONFIG_MVEBU_MBUS=y
-CONFIG_MVMDIO=y
-CONFIG_MV_XOR=y
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NEED_KUSER_HELPERS=y
-CONFIG_NEED_PER_CPU_KM=y
-# CONFIG_NET_VENDOR_AURORA is not set
-CONFIG_NO_BOOTMEM=y
-CONFIG_OF=y
-CONFIG_OF_ADDRESS=y
-CONFIG_OF_ADDRESS_PCI=y
-CONFIG_OF_EARLY_FLATTREE=y
-CONFIG_OF_FLATTREE=y
-CONFIG_OF_GPIO=y
-CONFIG_OF_IRQ=y
-CONFIG_OF_MDIO=y
-CONFIG_OF_NET=y
-CONFIG_OF_PCI=y
-CONFIG_OF_PCI_IRQ=y
-CONFIG_OF_RESERVED_MEM=y
-CONFIG_OLD_SIGACTION=y
-CONFIG_OLD_SIGSUSPEND3=y
-CONFIG_ORION_WATCHDOG=y
-CONFIG_PAGE_OFFSET=0xC0000000
-CONFIG_PCI=y
-CONFIG_PCI_DOMAINS=y
-CONFIG_PCI_DOMAINS_GENERIC=y
-CONFIG_PERF_USE_VMALLOC=y
-CONFIG_PGTABLE_LEVELS=2
-CONFIG_PHYLIB=y
-CONFIG_PLAT_ORION=y
-CONFIG_PLAT_ORION_LEGACY=y
-CONFIG_RATIONAL=y
-# CONFIG_RCU_EXPERT is not set
-# CONFIG_RCU_NEED_SEGCBLIST is not set
-# CONFIG_RCU_STALL_COMMON is not set
-CONFIG_REGMAP=y
-CONFIG_REGMAP_I2C=y
-CONFIG_REGMAP_MMIO=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_I2C_AND_SPI=y
-CONFIG_RTC_MC146818_LIB=y
-CONFIG_RWSEM_XCHGADD_ALGORITHM=y
-# CONFIG_SCHED_INFO is not set
-# CONFIG_SCSI_DMA is not set
-CONFIG_SERIAL_8250_FSL=y
-CONFIG_SPARSE_IRQ=y
-CONFIG_SPLIT_PTLOCK_CPUS=999999
-CONFIG_SRAM=y
-CONFIG_SRAM_EXEC=y
-CONFIG_SRCU=y
-CONFIG_SWIOTLB=y
-CONFIG_SWPHY=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-CONFIG_TICK_CPU_ACCOUNTING=y
-CONFIG_TIMER_OF=y
-CONFIG_TIMER_PROBE=y
-CONFIG_TINY_SRCU=y
-CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
-CONFIG_USB_SUPPORT=y
-CONFIG_USE_OF=y
-CONFIG_VECTORS_BASE=0xffff0000
-# CONFIG_VFP is not set
-CONFIG_WATCHDOG_CORE=y
-CONFIG_XZ_DEC_ARM=y
-CONFIG_XZ_DEC_BCJ=y
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ZBOOT_ROM_TEXT=0x0
+++ /dev/null
-#!/bin/sh
-#
-# Copyright (C) 2010 OpenWrt.org
-#
-# This is free software, licensed under the GNU General Public License v2.
-# See /LICENSE for more information.
-#
-
-#
-# This script sets system defaults for the hardware on firstboot
-#
-
-. /lib/functions.sh
-
-wrt350nv2_default() {
-# leds
- uci batch <<__EOF
-set system.power_led=led
-set system.power_led.name='Power LED (green)'
-set system.power_led.sysfs='wrt350nv2:green:power'
-set system.power_led.default='1'
-set system.wifi_led=led
-set system.wifi_led.name='Wireless LED (green)'
-set system.wifi_led.sysfs='wrt350nv2:green:wireless'
-set system.wifi_led.trigger='netdev'
-set system.wifi_led.dev='wlan0'
-set system.wifi_led.mode='link tx rx'
-set system.wifi_led.default='0'
-commit system
-__EOF
-
-# add mac address from U-Boot partition to lan and wan devices
- MTD=$(grep -e 'u-boot' /proc/mtd)
- MTD=$(echo ${MTD} | sed 's/[a-z]*\([0-9]*\):.*/\1/')
- [ -n "${MTD}" ] && {
- MACADDR=$(dd if=/dev/mtdblock${MTD} bs=1 skip=262048 count=6 2>/dev/null | hexdump -e '1/1 "%02x"')
- MACADDR2=$(( 0x${MACADDR} + 1))
- MACADDR2=$(printf "%012x" ${MACADDR2})
-
- MACADDR=$(echo ${MACADDR} | sed 's/\(..\)/\1:/g' | sed 's/:$//')
- MACADDR2=$(echo ${MACADDR2} | sed 's/\(..\)/\1:/g' | sed 's/:$//')
-
- uci set network.eth0.macaddr=${MACADDR}
- uci set network.lan.macaddr=${MACADDR}
- uci set network.wan.macaddr=${MACADDR2}
- uci commit network
- }
-}
-
-case "$(board_name)" in
- 'Linksys WRT350N v2')
- wrt350nv2_default
- ;;
-esac
+++ /dev/null
-#
-# Copyright (C) 2010-2011 OpenWrt.org
-#
-
-# use default "image" for PART_NAME
-# use default for platform_do_upgrade()
-
-platform_check_image() {
- [ "$#" -gt 1 ] && { echo 'Too many arguments. Only flash file expected.'; return 1; }
-
- local hardware="$(board_name)"
- local magic="$(get_magic_word "$1")"
- local magic_long="$(get_magic_long "$1")"
-
- case "${hardware}" in
- # hardware with a direct uImage partition
- # image header format as described in U-Boot's include/image.h
- # see http://git.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=blob;f=include/image.h
- 'Linksys WRT350N v2')
- [ "${magic_long}" != '27051956' ] && {
- echo "Invalid image type ${magic_long}."
- return 1
- }
- return 0
- ;;
- # Netgear WNR854T (has uImage as file inside a JFFS2 partition)
- 'Netgear WNR854T')
- [ "${magic}" != '8519' ] && {
- echo "Invalid image type ${magic}."
- return 1
- }
- return 0
- ;;
- esac
-
- echo "Sysupgrade is not yet supported on ${hardware}."
- return 1
-}
+++ /dev/null
-#
-# Copyright (C) 2008-2010 OpenWrt.org
-#
-# This is free software, licensed under the GNU General Public License v2.
-# See /LICENSE for more information.
-#
-
-BOARDNAME:=Generic
-FEATURES+=squashfs
-
-define Target/Description
- Build firmware images for Marvell Orion based boards that boot from internal flash.
- (e.g.: Linksys WRT350N v2, Netgear WNR854T, ...)
-endef
+++ /dev/null
-CONFIG_ATA=y
-CONFIG_BLK_DEV_DM=y
-CONFIG_BLK_DEV_DM_BUILTIN=y
-CONFIG_BLK_DEV_MD=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_BLK_SCSI_REQUEST=y
-CONFIG_CRC16=y
-CONFIG_CRYPTO_CRC32C=y
-CONFIG_DAX=y
-# CONFIG_DM_CRYPT is not set
-# CONFIG_DM_MIRROR is not set
-# CONFIG_DM_SNAPSHOT is not set
-CONFIG_EXT4_FS=y
-CONFIG_FS_MBCACHE=y
-CONFIG_GENERIC_PHY=y
-CONFIG_GLOB=y
-CONFIG_HWMON=y
-CONFIG_JBD2=y
-CONFIG_MACH_DT2=y
-CONFIG_MACH_NET2BIG=y
-# CONFIG_MACH_WN802T is not set
-# CONFIG_MACH_WNR854T is not set
-# CONFIG_MACH_WRT350N_V2 is not set
-CONFIG_MD=y
-CONFIG_MD_AUTODETECT=y
-CONFIG_MD_LINEAR=y
-# CONFIG_MD_MULTIPATH is not set
-CONFIG_MD_RAID0=y
-CONFIG_MD_RAID1=y
-# CONFIG_MD_RAID10 is not set
-# CONFIG_MD_RAID456 is not set
-CONFIG_NLS=y
-CONFIG_SATA_MV=y
-CONFIG_SCSI=y
-CONFIG_SCSI_DMA=y
-CONFIG_SG_POOL=y
-CONFIG_USB=y
-CONFIG_USB_COMMON=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_EHCI_HCD_ORION=y
-CONFIG_USB_EHCI_HCD_PLATFORM=y
-CONFIG_USB_STORAGE=y
+++ /dev/null
-#
-# Copyright (C) 2008-2010 OpenWrt.org
-#
-# This is free software, licensed under the GNU General Public License v2.
-# See /LICENSE for more information.
-#
-
-BOARDNAME:=Internal Hard-Disk
-FEATURES+=targz
-DEVICE_TYPE:=nas
-
-define Target/Description
- Build firmware images for Marvell Orion based boards that boot directly from internal disk storage.
- (e.g.: Freecom DataTank 2, ...)
-endef
+++ /dev/null
-#
-# Copyright (C) 2008-2010 OpenWrt.org
-#
-# This is free software, licensed under the GNU General Public License v2.
-# See /LICENSE for more information.
-#
-include $(TOPDIR)/rules.mk
-include $(INCLUDE_DIR)/image.mk
-
-include $(SUBTARGET).mk
-
-$(eval $(call BuildImage))
+++ /dev/null
-#
-# Copyright (C) 2008-2015 OpenWrt.org
-#
-# This is free software, licensed under the GNU General Public License v2.
-# See /LICENSE for more information.
-#
-
-### DO NOT INDENT LINES CONTAINING $(call xyz) AS THIS MAY CHANGE THE CONTEXT
-### OF THE FIRST LINE IN THE CALLED VARIABLE (NOTE: variable!)
-### see http://www.gnu.org/software/make/manual/html_node/Call-Function.html#Call-Function
-### ACTUALLY IT IS A SIMPLE MACRO EXPANSION
-
-### use round brackets for make variables, and curly brackets for shell variables
-
-
-## Kernel mtd partition size in KiB
-KERNEL_MTD_SIZE:=1280
-
-# Netgear WNR854T: erase size is 128KiB = 0x00020000 = 131072
-ERASE_SIZE_128K:=128
-
-# Linksys WRT350N v2: erase size is 64KiB = 0x00010000 = 65536
-ERASE_SIZE_64K:=64
-
-# define JFFS2 sizes for include/image.mk
-JFFS2_BLOCKSIZE:=64k 128k
-
-
-###
-### Image/BuildKernel
-###
-
-define Image/BuildKernel
-### Dummy comment for indented calls of Image/BuildKernel
-
- ## Netgear WN802T: mach id 3306 (0x0cea)
-$(call Image/BuildKernel/ARM/zImage,wn802t,"\x0c\x1c\xa0\xe3\xea\x10\x81\xe3")
-$(call Image/BuildKernel/ARM/uImage,wn802t)
-ifeq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),y)
-$(call Image/BuildKernel/ARM/zImage,wn802t,"\x0c\x1c\xa0\xe3\xea\x10\x81\xe3",-initramfs)
-$(call Image/BuildKernel/ARM/uImage,wn802t,-initramfs)
-endif
- ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),y) # nothing more to do for a ramdisk build
-$(call Image/BuildKernel/JFFS2uImage,wn802t,$(ERASE_SIZE_64K),uImage)
-$(call Image/Default/FileSizeCheck,$(KDIR)/wn802t-uImage.jffs2,$(shell expr $(KERNEL_MTD_SIZE) \* 1024))
- endif
-
- ## Netgear WNR854T: mach id 1801 (0x0709)
-$(call Image/BuildKernel/ARM/zImage,wnr854t,"\x07\x1c\xa0\xe3\x09\x10\x81\xe3")
-$(call Image/BuildKernel/ARM/uImage,wnr854t)
-ifeq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),y)
-$(call Image/BuildKernel/ARM/zImage,wnr854t,"\x07\x1c\xa0\xe3\x09\x10\x81\xe3",-initramfs)
-$(call Image/BuildKernel/ARM/uImage,wnr854t,-initramfs)
-endif
- ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),y) # nothing more to do for a ramdisk build
-$(call Image/BuildKernel/JFFS2uImage,wnr854t,$(ERASE_SIZE_128K),uImage)
-$(call Image/Default/FileSizeCheck,$(KDIR)/wnr854t-uImage.jffs2,$(shell expr $(KERNEL_MTD_SIZE) \* 1024))
- endif
-
- ## Linksys WRT350N v2: mach id 1633 (0x0661)
-$(call Image/BuildKernel/ARM/zImage,wrt350nv2,"\x06\x1c\xa0\xe3\x61\x10\x81\xe3")
-$(call Image/BuildKernel/ARM/uImage,wrt350nv2)
-ifeq ($($CONFIG_TARGET_ROOTFS_INITRAMFS),y)
-$(call Image/BuildKernel/ARM/zImage,wrt350nv2,"\x06\x1c\xa0\xe3\x61\x10\x81\xe3",-initramfs)
-$(call Image/BuildKernel/ARM/uImage,wrt350nv2-initramfs)
-endif
- ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),y) # nothing more to do for a ramdisk build
-$(call Image/Default/FileSizeCheck,$(KDIR)/wrt350nv2-uImage,$(shell expr $(KERNEL_MTD_SIZE) \* 1024))
- endif
-
- ## Buffalo Terastation Pro II/Live: mach id 1584 (0x0630)
-$(call Image/BuildKernel/ARM/zImage,terastation-pro2,"\x06\x1c\xa0\xe3\x30\x10\x81\xe3")
-$(call Image/BuildKernel/ARM/uImage,terastation-pro2)
-ifeq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),y)
-$(call Image/BuildKernel/ARM/zImage,terastation-pro2,"\x06\x1c\xa0\xe3\x30\x10\x81\xe3",-initramfs)
-$(call Image/BuildKernel/ARM/uImage,terastation-pro2,-initramfs)
-endif
-endef
-
-define Image/BuildKernel/ARM/zImage
- # merge machine id and regular zImage into one file
- # parameters: 1 = machine name, 2 = machine id as string in quotes
- # $(BOARD) kernel zImage for $(1)
- echo -en $(2) > '$(KDIR)/$(1)-zImage$(3)'
- cat '$(KDIR)/zImage$(3)' >> '$(KDIR)/$(1)-zImage$(3)'
-endef
-
-define Image/BuildKernel/ARM/uImage
- # create uImage from zImage
- # parameters: 1 = machine name
- # $(BOARD) kernel uImage for $(1)
- '$(STAGING_DIR_HOST)/bin/mkimage' -A arm -O linux -T kernel \
- -C none -a 0x00008000 -e 0x00008000 -n 'Linux-$(LINUX_VERSION)' \
- -d '$(KDIR)/$(1)-zImage$(2)' '$(KDIR)/$(1)-uImage$(2)'
- ifeq ($(2),-initramfs) # only copy uImage for ramdisk build
- cp '$(KDIR)/$(1)-uImage-initramfs' '$(BIN_DIR)/openwrt-$(1)-uImage-initramfs'
- endif
-endef
-
-define Image/BuildKernel/JFFS2uImage
- # create JFFS2 partition with uImage file (result is already padded to erase size)
- # parameters: 1 = machine name, 2 = erase size in KiB, 3 = uImage file name
- # $(BOARD) kernel uImage for $(1) in JFFS2-$(2)k partition
- rm -rf '$(TMP_DIR)/$(1)_jffs2_uimage'
- mkdir '$(TMP_DIR)/$(1)_jffs2_uimage'
- cp '$(KDIR)/$(1)-uImage' '$(TMP_DIR)/$(1)_jffs2_uimage/$(3)'
- $(STAGING_DIR_HOST)/bin/mkfs.jffs2 --compression-mode=none --pad --little-endian --squash -e $(2)KiB -o '$(KDIR)/$(1)-uImage.jffs2' -d '$(TMP_DIR)/$(1)_jffs2_uimage'
- rm -rf '$(TMP_DIR)/$(1)_jffs2_uimage'
-endef
-
-define Image/Default/FileSizeCheck
- # parameters: 1 = file path, 2 = maximum size in bytes
- [ $(stat -c %s '$(1)') -le $(2) ] || { echo ' ERROR: $(1) too big (> $(2) bytes)'; rm -f $(1); }
-endef
-
-
-###
-### Image/Build
-###
-
-define Image/Build
-### Dummy comment for indented calls of Image/Build with $(1)
-
- ## Prepare rootfs
-$(call Image/Build/$(1),$(1))
-
- ## Netgear WN802T
-$(call Image/Build/Default,$(1),wn802t,$(ERASE_SIZE_64K),$(KERNEL_MTD_SIZE),.jffs2,NG_WN802T)
-
- ## Netgear WNR854T
-$(call Image/Build/Default,$(1),wnr854t,$(ERASE_SIZE_128K),$(KERNEL_MTD_SIZE),.jffs2,NG_WNR854T)
-
- ## Linksys WRT350N v2
-$(call Image/Build/Linksys/wrt350nv2,$(1),wrt350nv2,$(ERASE_SIZE_64K),$(KERNEL_MTD_SIZE),)
-
- ## Buffalo Terastation Pro II/Live
-$(call Image/Build/Default,$(1),terastation-pro2,$(ERASE_SIZE_128K),$(KERNEL_MTD_SIZE),.jffs2,TERASTATION_PRO2)
-endef
-
-define Image/Build/squashfs
-$(call prepare_generic_squashfs,$(KDIR)/root.squashfs)
-endef
-
-## generate defines for all JFFS2 block sizes
-define Image/Build/jffs2/sub
- $(eval define Image/Build/jffs2-$(1)
- cp '$$(KDIR)/root.jffs2-$(1)' '$$(BIN_DIR)/$$(IMG_PREFIX)-root.jffs2-$(1)'
- endef)
-endef
-
-$(foreach SZ,$(JFFS2_BLOCKSIZE),$(call Image/Build/jffs2/sub,$(SZ)))
-
-define Image/Build/Default
- # parameters: 1 = rootfs type, 2 = machine name, 3 = erase size in KiB, 4 = kernel mtd size in KiB, 5 = kernel file suffix, 6 = header
- ifeq ($(findstring jffs2-,$(1)),jffs2-) # JFFS2: build only image fitting to erase size
- ifeq ($(1),jffs2-$(3)k)
-$(call Image/Build/Default/sysupgrade,$(1),$(2),$(4),$(5))
-$(call Image/Build/Default/factory,$(1),$(2),$(6))
- endif
- else
- ifeq ($(1),ext4) # EXT4: ignore
- # do nothing
- else # do all other images
-$(call Image/Build/Default/sysupgrade,$(1),$(2),$(4),$(5))
-$(call Image/Build/Default/factory,$(1),$(2),$(6))
- endif
- endif
-endef
-
-define Image/Build/Default/sysupgrade
- # parameters: 1 = rootfs type, 2 = machine name, 3 = pad size in KiB (kernel mtd size or erase size), 4 = kernel file suffix
- # $(BOARD) $(1) sysupgrade image for $(2)
- ( \
- dd if='$(KDIR)/$(2)-uImage$(4)' bs=$(3)k conv=sync; \
- dd if='$(KDIR)/root.$(1)'; \
- ) > '$(BIN_DIR)/openwrt-$(2)-$(1)-sysupgrade.img'
-endef
-
-define Image/Build/Default/factory
- # parameters: 1 = rootfs type, 2 = machine name, 3 = header
- # $(BOARD) $(1) factory upgrade image for $(2)
- '$(STAGING_DIR_HOST)/bin/add_header' $(3) '$(BIN_DIR)/openwrt-$(2)-$(1)-sysupgrade.img' '$(BIN_DIR)/openwrt-$(2)-$(1)-factory.img'
-endef
-
-##
-## Image/Build/Linksys
-##
-
-define Image/Build/Linksys/wrt350nv2
- # parameters: 1 = rootfs type, 2 = machine name, 3 = erase size in KiB, 4 = kernel mtd size in KiB, 5 = kernel file suffix
- ifeq ($(findstring jffs2-,$(1)),jffs2-) # JFFS2: build only image fitting to erase size
- ifeq ($(1),jffs2-$(3)k)
-$(call Image/Build/Default/sysupgrade,$(1),$(2),$(4),$(5))
-$(call Image/Build/Linksys/wrt350nv2-builder,$(1),$(2))
- endif
- else
- ifeq ($(1),ext4) # EXT4: ignore
- # do nothing
- else # do all other images
-$(call Image/Build/Default/sysupgrade,$(1),$(2),$(4),$(5))
-$(call Image/Build/Linksys/wrt350nv2-builder,$(1),$(2))
- endif
- endif
-endef
-
-define Image/Build/Linksys/wrt350nv2-builder
- # parameters: 1 = rootfs type, 2 = machine name
- # $(BOARD) $(1) factory and recovery image for $(2) via wrt350nv2-builder
- rm -rf '$(TMP_DIR)/$(2)_factory'
- mkdir '$(TMP_DIR)/$(2)_factory'
- # create parameter file
- echo ':image 0 $(BIN_DIR)/openwrt-$(2)-$(1)-sysupgrade.img' > '$(TMP_DIR)/$(2)_factory/$(2).par'
- [ ! -f '$(STAGING_DIR_HOST)/share/wrt350nv2-builder/u-boot.bin' ] || ( \
- echo ':u-boot 0 $(STAGING_DIR_HOST)/share/wrt350nv2-builder/u-boot.bin' >> '$(TMP_DIR)/$(2)_factory/$(2).par'; \
- )
- echo '#version 0x2020' >> '$(TMP_DIR)/$(2)_factory/$(2).par'
- # create bin file for recovery and factory image
- -( \
- cd '$(TMP_DIR)/$(2)_factory'; \
- '$(STAGING_DIR_HOST)/bin/wrt350nv2-builder' -b '$(TMP_DIR)/$(2)_factory/$(2).par'; \
- ) && $(CP) '$(TMP_DIR)/$(2)_factory/wrt350n.bin' '$(BIN_DIR)/openwrt-$(2)-$(1)-recovery.bin' && \
- ( \
- cd '$(TMP_DIR)/$(2)_factory'; \
- zip 'wrt350n.zip' 'wrt350n.bin'; \
- ) && '$(STAGING_DIR_HOST)/bin/wrt350nv2-builder' -z '$(TMP_DIR)/$(2)_factory/wrt350n.zip' '$(BIN_DIR)/openwrt-$(2)-$(1)-factory.img'
- rm -rf '$(TMP_DIR)/$(2)_factory'
-endef
-
-
-###
-### Image/PreReq
-###
-
-## Dependency for WRT350N v2 factory image
-$(eval $(call RequireCommand,zip, \
- Please install zip. \
-))
+++ /dev/null
-#
-# Copyright (C) 2008-2010 OpenWrt.org
-#
-# This is free software, licensed under the GNU General Public License v2.
-# See /LICENSE for more information.
-#
-
-define Image/BuildKernelMachId
- echo -en "\x$(2)\x1c\xa0\xe3\x$(3)\x10\x81\xe3" > $(KDIR)/$(1)-zImage
- cat $(LINUX_DIR)/arch/arm/boot/zImage >> $(KDIR)/$(1)-zImage
- $(STAGING_DIR_HOST)/bin/mkimage -A arm -O linux -T kernel \
- -C none -a 0x00008000 -e 0x00008000 -n 'Linux-$(LINUX_VERSION)' \
- -d $(KDIR)/$(1)-zImage $(KDIR)/$(1)-uImage
- cp $(KDIR)/$(1)-uImage $(BIN_DIR)/openwrt-$(1)-uImage
-endef
-
-define Image/BuildKernel
- # Orion Kernel uImages
- # DT2: mach id 1514 (0x5EA)
- $(call Image/BuildKernelMachId,dt2,05,ea)
- # LaCie 2big Network: mach id 2342 (0x926)
- $(call Image/BuildKernelMachId,net2big,09,26)
-endef
-
-define Image/Build/Freecom
- # Orion Freecom Images
- # backup unwanted files
- rm -rf ${TMP_DIR}/$2_backup
- mkdir ${TMP_DIR}/$2_backup
- -mv $(TARGET_DIR)/{var,jffs,rom} ${TMP_DIR}/$2_backup
- # add extra files
- $(INSTALL_DIR) $(TARGET_DIR)/boot
- # TODO: Add special CMDLINE shim for webupgrade image here
- $(CP) $(KDIR)/dt2-uImage $(TARGET_DIR)/boot/uImage
- $(INSTALL_DIR) $(TARGET_DIR)/var
- # create image
- $(TAR) cfj $(BIN_DIR)/openwrt-$(2)-$(1).img --numeric-owner --owner=0 --group=0 -C $(TARGET_DIR)/ .
- $(STAGING_DIR_HOST)/bin/encode_crc $(BIN_DIR)/openwrt-$(2)-$(1).img $(BIN_DIR)/openwrt-$(2)-$(1)-webupgrade.img $(3)
- # remove extra files
- rm -rf $(TARGET_DIR)/{boot,var}
- # recover unwanted files
- -mv ${TMP_DIR}/$2_backup/* $(TARGET_DIR)/
- rm -rf ${TMP_DIR}/$2_backup
-endef
-
-define Image/Build
-$(call Image/Build/$(1),$(1))
-$(call Image/Build/Freecom,$(1),dt2,DT,$(1))
-endef
-
-define Image/Build/squashfs
-$(call prepare_generic_squashfs,$(KDIR)/root.squashfs)
- ( \
- dd if=$(KDIR)/uImage bs=1024k conv=sync; \
- dd if=$(KDIR)/root.$(1) bs=128k conv=sync; \
- ) > $(BIN_DIR)/$(IMG_PREFIX)-$(1).img
-endef
+++ /dev/null
---- a/arch/arm/tools/mach-types
-+++ b/arch/arm/tools/mach-types
-@@ -268,6 +268,7 @@ yl9200 MACH_YL9200 YL9200 1507
- rd88f5182 MACH_RD88F5182 RD88F5182 1508
- kurobox_pro MACH_KUROBOX_PRO KUROBOX_PRO 1509
- mx31_3ds MACH_MX31_3DS MX31_3DS 1511
-+dt2 MACH_DT2 DT2 1514
- qong MACH_QONG QONG 1524
- omap2evm MACH_OMAP2EVM OMAP2EVM 1534
- omap3evm MACH_OMAP3EVM OMAP3EVM 1535
-@@ -530,6 +531,7 @@ mx53_loco MACH_MX53_LOCO MX53_LOCO 32
- wario MACH_WARIO WARIO 3288
- cm_t3730 MACH_CM_T3730 CM_T3730 3290
- hrefv60 MACH_HREFV60 HREFV60 3293
-+wn802t MACH_WN802T WN802T 3306
- armlex4210 MACH_ARMLEX4210 ARMLEX4210 3361
- snowball MACH_SNOWBALL SNOWBALL 3363
- xilinx_ep107 MACH_XILINX_EP107 XILINX_EP107 3378
+++ /dev/null
---- a/arch/arm/mach-orion5x/wrt350n-v2-setup.c
-+++ b/arch/arm/mach-orion5x/wrt350n-v2-setup.c
-@@ -134,11 +134,11 @@ static struct mtd_partition wrt350n_v2_n
- {
- .name = "kernel",
- .offset = 0x00000000,
-- .size = 0x00760000,
-+ .size = 0x00140000, // change to kernel mtd size here (1/3)
- }, {
- .name = "rootfs",
-- .offset = 0x001a0000,
-- .size = 0x005c0000,
-+ .offset = 0x00140000, // change to kernel mtd size here (2/3)
-+ .size = 0x00610000, // adopt to kernel mtd size here (3/3) = 0x00750000 - <kernel mtd size>
- }, {
- .name = "lang",
- .offset = 0x00760000,
-@@ -151,6 +151,14 @@ static struct mtd_partition wrt350n_v2_n
- .name = "u-boot",
- .offset = 0x007c0000,
- .size = 0x00040000,
-+ }, {
-+ .name = "eRcOmM_do_not_touch",
-+ .offset = 0x00750000,
-+ .size = 0x00010000, // erasesize
-+ }, {
-+ .name = "image", // for sysupgrade
-+ .offset = 0x00000000,
-+ .size = 0x00750000,
- },
- };
-
+++ /dev/null
---- a/arch/arm/mach-orion5x/wnr854t-setup.c
-+++ b/arch/arm/mach-orion5x/wnr854t-setup.c
-@@ -57,15 +57,19 @@ static struct mtd_partition wnr854t_nor_
- {
- .name = "kernel",
- .offset = 0x00000000,
-- .size = 0x00100000,
-+ .size = 0x00140000,
- }, {
- .name = "rootfs",
-- .offset = 0x00100000,
-- .size = 0x00660000,
-+ .offset = 0x00140000,
-+ .size = 0x00620000,
- }, {
- .name = "uboot",
- .offset = 0x00760000,
- .size = 0x00040000,
-+ }, {
-+ .name = "image", // for sysupgrade
-+ .offset = 0x00000000,
-+ .size = 0x00760000,
- },
- };
-
+++ /dev/null
---- a/arch/arm/mach-orion5x/Kconfig
-+++ b/arch/arm/mach-orion5x/Kconfig
-@@ -49,6 +49,13 @@ config MACH_RD88F5182_DT
- Say 'Y' here if you want your kernel to support the Marvell
- Orion-NAS (88F5182) RD2, Flattened Device Tree.
-
-+config MACH_DT2
-+ bool "Freecom DataTank Gateway"
-+ select I2C_BOARDINFO
-+ help
-+ Say 'Y' here if you want your kernel to support the
-+ Freecom DataTank Gateway
-+
- config MACH_KUROBOX_PRO
- bool "KuroBox Pro"
- select I2C_BOARDINFO if I2C
---- a/arch/arm/mach-orion5x/Makefile
-+++ b/arch/arm/mach-orion5x/Makefile
-@@ -16,6 +16,7 @@ obj-$(CONFIG_MACH_TS78XX) += ts78xx-setu
- obj-$(CONFIG_MACH_MV2120) += mv2120-setup.o
- obj-$(CONFIG_MACH_NET2BIG) += net2big-setup.o
- obj-$(CONFIG_MACH_WNR854T) += wnr854t-setup.o
-+obj-$(CONFIG_MACH_DT2) += dt2-setup.o
- obj-$(CONFIG_MACH_RD88F5181L_GE) += rd88f5181l-ge-setup.o
- obj-$(CONFIG_MACH_RD88F5181L_FXO) += rd88f5181l-fxo-setup.o
- obj-$(CONFIG_MACH_RD88F6183AP_GE) += rd88f6183ap-ge-setup.o
---- /dev/null
-+++ b/arch/arm/mach-orion5x/dt2-common.h
-@@ -0,0 +1,82 @@
-+#ifndef __INC_DT2_COMMON_H
-+#define __INC_DT2_COMMON_H
-+
-+#define ATAG_MV_UBOOT 0x41000403
-+
-+struct tag_mv_uboot {
-+ u32 uboot_version;
-+ u32 tclk;
-+ u32 sysclk;
-+ u32 isUsbHost;
-+ u32 overEthAddr;
-+ u8 dt2_eeprom[256];
-+};
-+
-+#define DT2_EEPROM_ADDR 0x50
-+#define DT2_EEPROM_OFFSET 0
-+#define DT2_EEPROM_LENGTH 256
-+
-+#define DT2_SERIAL_NUMBER_DEFAULT "run on default\0"
-+#define DT2_REVISION_DEFAULT_INIT 0xFF
-+#define DT2_CONFIG_FLAGS_DEFAULT 0x00
-+
-+#define _PACKED_ __attribute__((packed))
-+
-+struct DT2_EEPROM_SD_CONFIG {
-+ unsigned int ram_1;
-+ unsigned int ram_2;
-+ unsigned int ram_3;
-+ unsigned int ram_4;
-+ unsigned char ram_5;
-+ unsigned char ram_6;
-+ unsigned short ram_7;
-+ unsigned int magic_id;
-+ } _PACKED_; // 24 Bytes in total
-+
-+struct DT2_EEPROM_FC_CONFIG {
-+ unsigned char rtc_sts_mask;
-+ unsigned char rtc_sts_init;
-+ unsigned char rtc_int_mask;
-+ unsigned char rtc_int_init;
-+ unsigned char rtc_atrim_init;
-+ unsigned char rtc_dtrim_init;
-+ unsigned char dummy1;
-+ unsigned char dummy2;
-+ unsigned char dt2_config_flags; /* 0x80 to load rtc_values to RTC */
-+ unsigned char dt2_revision; /* upper nibble is HW, lower nibble is FW */
-+ unsigned char dt2_serial_number[16]; /* Serial number of DT-2 */
-+ } _PACKED_; // 26 Bytes in total
-+
-+#define CFG_LOAD_RTC_VALUES 0x80
-+
-+struct DT2_EEPROM_GW_CONFIG {
-+ unsigned int dummy1;
-+ unsigned int dummy2;
-+ unsigned int dummy3;
-+ unsigned char dummy4;
-+ unsigned char tos_video_val1;
-+ unsigned char tos_video_val2;
-+ unsigned char tos_voip_val;
-+ unsigned char qos_igmp_cfg;
-+ unsigned char num_of_ifs;
-+ unsigned short vlan_ports_if[3];
-+ unsigned char mac_addr[3][6];
-+ } _PACKED_; // 42 Bytes in total
-+
-+#define _SIZE_OF_ALL_STRUCTS_ (sizeof(struct DT2_EEPROM_SD_CONFIG) + sizeof(struct DT2_EEPROM_FC_CONFIG) + sizeof(struct DT2_EEPROM_GW_CONFIG))
-+
-+// MV = EEPROM - SD - FC - GW - CRC
-+struct DT2_EEPROM_MV_CONFIG {
-+ unsigned int reg_addr[(DT2_EEPROM_LENGTH - _SIZE_OF_ALL_STRUCTS_ - sizeof(unsigned int)) / (sizeof(unsigned int) * 2)];
-+ unsigned int reg_data[(DT2_EEPROM_LENGTH - _SIZE_OF_ALL_STRUCTS_ - sizeof(unsigned int)) / (sizeof(unsigned int) * 2)];
-+ } _PACKED_;
-+
-+struct DT2_EEPROM_STRUCT {
-+ struct DT2_EEPROM_MV_CONFIG mv;
-+ struct DT2_EEPROM_SD_CONFIG sd;
-+ struct DT2_EEPROM_FC_CONFIG fc;
-+ struct DT2_EEPROM_GW_CONFIG gw;
-+ unsigned int crc;
-+ } _PACKED_;
-+
-+#endif
---- /dev/null
-+++ b/arch/arm/mach-orion5x/dt2-setup.c
-@@ -0,0 +1,443 @@
-+/*
-+ * arch/arm/mach-orion5x/dt2-setup.c
-+ *
-+ * Freecom DataTank Gateway Setup
-+ *
-+ * Copyright (C) 2009 Zintis Petersons <Zintis.Petersons@abcsolutions.lv>
-+ *
-+ * This file is licensed under the terms of the GNU General Public
-+ * License version 2. This program is licensed "as is" without any
-+ * warranty of any kind, whether express or implied.
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+#include <linux/platform_device.h>
-+#include <linux/pci.h>
-+#include <linux/irq.h>
-+#include <linux/mtd/physmap.h>
-+#include <linux/mv643xx_eth.h>
-+#include <linux/ethtool.h>
-+#include <linux/if_ether.h>
-+#include <net/dsa.h>
-+#include <linux/ata_platform.h>
-+#include <linux/i2c.h>
-+#include <linux/reboot.h>
-+#include <linux/interrupt.h>
-+#include <asm/mach-types.h>
-+#include <asm/gpio.h>
-+#include <asm/mach/arch.h>
-+#include <asm/mach/pci.h>
-+#include "orion5x.h"
-+#include "common.h"
-+#include "mpp.h"
-+
-+/*****************************************************************************
-+ * DT2 local
-+ ****************************************************************************/
-+#include <asm/setup.h>
-+#include "dt2-common.h"
-+
-+u32 mvUbootVer = 0;
-+u32 mvTclk = 166666667;
-+u32 mvSysclk = 200000000;
-+u32 mvIsUsbHost = 1;
-+u32 overEthAddr = 0;
-+u32 gBoardId = -1;
-+struct DT2_EEPROM_STRUCT dt2_eeprom;
-+
-+/*****************************************************************************
-+ * DT2 Info
-+ ****************************************************************************/
-+/*
-+ * PCI
-+ */
-+
-+#define DT2_PCI_SLOT0_OFFS 7
-+#define DT2_PCI_SLOT0_IRQ_A_PIN 3
-+#define DT2_PCI_SLOT0_IRQ_B_PIN 2
-+
-+#define DT2_PIN_GPIO_SYNC 25
-+#define DT2_PIN_GPIO_POWER 24
-+#define DT2_PIN_GPIO_UNPLUG1 23
-+#define DT2_PIN_GPIO_UNPLUG2 22
-+#define DT2_PIN_GPIO_RESET 4
-+
-+#define DT2_NOR_BOOT_BASE 0xf4000000
-+#define DT2_NOR_BOOT_SIZE SZ_512K
-+
-+#define DT2_LEDS_BASE 0xfa000000
-+#define DT2_LEDS_SIZE SZ_1K
-+
-+/*****************************************************************************
-+ * 512K NOR Flash on Device bus Boot CS
-+ ****************************************************************************/
-+
-+static struct mtd_partition dt2_partitions[] = {
-+ {
-+ .name = "u-boot",
-+ .size = 0x00080000,
-+ .offset = 0,
-+ },
-+};
-+
-+static struct physmap_flash_data dt2_nor_flash_data = {
-+ .width = 1, /* 8 bit bus width */
-+ .parts = dt2_partitions,
-+ .nr_parts = ARRAY_SIZE(dt2_partitions)
-+};
-+
-+static struct resource dt2_nor_flash_resource = {
-+ .flags = IORESOURCE_MEM,
-+ .start = DT2_NOR_BOOT_BASE,
-+ .end = DT2_NOR_BOOT_BASE + DT2_NOR_BOOT_SIZE - 1,
-+};
-+
-+static struct platform_device dt2_nor_flash = {
-+ .name = "physmap-flash",
-+ .id = 0,
-+ .dev = {
-+ .platform_data = &dt2_nor_flash_data,
-+ },
-+ .resource = &dt2_nor_flash_resource,
-+ .num_resources = 1,
-+};
-+
-+/*****************************************************************************
-+ * PCI
-+ ****************************************************************************/
-+
-+void __init dt2_pci_preinit(void)
-+{
-+ int pin, irq;
-+
-+ /*
-+ * Configure PCI GPIO IRQ pins
-+ */
-+ pin = DT2_PCI_SLOT0_IRQ_A_PIN;
-+ if (gpio_request(pin, "PCI IntA") == 0) {
-+ if (gpio_direction_input(pin) == 0) {
-+ irq = gpio_to_irq(pin);
-+ irq_set_irq_type(irq, IRQ_TYPE_LEVEL_LOW);
-+ printk (KERN_INFO "PCI IntA IRQ: %d\n", irq);
-+ } else {
-+ printk(KERN_ERR "dt2_pci_preinit failed to "
-+ "irq_set_irq_type pin %d\n", pin);
-+ gpio_free(pin);
-+ }
-+ } else {
-+ printk(KERN_ERR "dt2_pci_preinit failed to request gpio %d\n", pin);
-+ }
-+
-+ pin = DT2_PCI_SLOT0_IRQ_B_PIN;
-+ if (gpio_request(pin, "PCI IntB") == 0) {
-+ if (gpio_direction_input(pin) == 0) {
-+ irq = gpio_to_irq(pin);
-+ irq_set_irq_type(irq, IRQ_TYPE_LEVEL_LOW);
-+ printk (KERN_INFO "PCI IntB IRQ: %d\n", irq);
-+ } else {
-+ printk(KERN_ERR "dt2_pci_preinit failed to "
-+ "irq_set_irq_type pin %d\n", pin);
-+ gpio_free(pin);
-+ }
-+ } else {
-+ printk(KERN_ERR "dt2_pci_preinit failed to gpio_request %d\n", pin);
-+ }
-+}
-+
-+static int __init dt2_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-+{
-+ int irq;
-+
-+ /*
-+ * Check for devices with hard-wired IRQs.
-+ */
-+ irq = orion5x_pci_map_irq(dev, slot, pin);
-+ if (irq != -1){
-+ printk(KERN_INFO "orion5x_pci_map_irq: %d\n", irq);
-+ return irq;
-+ }
-+
-+ /*
-+ * PCI IRQs are connected via GPIOs
-+ */
-+ switch (slot - DT2_PCI_SLOT0_OFFS) {
-+ case 0:
-+ if (pin == 1){
-+ irq = gpio_to_irq(DT2_PCI_SLOT0_IRQ_A_PIN);
-+ printk(KERN_INFO "dt2_pci_map_irq DT2_PCI_SLOT0_IRQ_A_PIN: %d\n", irq);
-+ }
-+ else {
-+ irq = gpio_to_irq(DT2_PCI_SLOT0_IRQ_B_PIN);
-+ printk(KERN_INFO "dt2_pci_map_irq DT2_PCI_SLOT0_IRQ_B_PIN: %d\n", irq);
-+ }
-+ default:
-+ irq = -1;
-+ printk(KERN_INFO "dt2_pci_map_irq IRQ: %d\n", irq);
-+ }
-+
-+ return irq;
-+}
-+
-+static struct hw_pci dt2_pci __initdata = {
-+ .nr_controllers = 2,
-+ .preinit = dt2_pci_preinit,
-+ .setup = orion5x_pci_sys_setup,
-+ .scan = orion5x_pci_sys_scan_bus,
-+ .map_irq = dt2_pci_map_irq,
-+};
-+
-+static int __init dt2_pci_init(void)
-+{
-+ if (machine_is_dt2())
-+ pci_common_init(&dt2_pci);
-+
-+ return 0;
-+}
-+
-+subsys_initcall(dt2_pci_init);
-+
-+/*****************************************************************************
-+ * Ethernet
-+ ****************************************************************************/
-+
-+static struct mv643xx_eth_platform_data dt2_eth_data = {
-+ .phy_addr = MV643XX_ETH_PHY_NONE,
-+ .speed = SPEED_1000,
-+ .duplex = DUPLEX_FULL,
-+};
-+
-+static struct dsa_chip_data dt2_switch_chip_data = {
-+ .port_names[0] = "wan",
-+ .port_names[1] = "lan1",
-+ .port_names[2] = "lan2",
-+ .port_names[3] = "cpu",
-+ .port_names[4] = "lan3",
-+ .port_names[5] = "lan4",
-+};
-+
-+/*****************************************************************************
-+ * RTC ISL1208 on I2C bus
-+ ****************************************************************************/
-+static struct i2c_board_info __initdata dt2_i2c_rtc = {
-+ I2C_BOARD_INFO("isl1208", 0x6F),
-+};
-+
-+/*****************************************************************************
-+ * Sata
-+ ****************************************************************************/
-+static struct mv_sata_platform_data dt2_sata_data = {
-+ .n_ports = 2,
-+};
-+
-+/*****************************************************************************
-+ * General Setup
-+ ****************************************************************************/
-+static unsigned int dt2_mpp_modes[] __initdata = {
-+ MPP0_GPIO, // RTC interrupt
-+ MPP1_GPIO, // 88e6131 interrupt
-+ MPP2_GPIO, // PCI_intB
-+ MPP3_GPIO, // PCI_intA
-+ MPP4_GPIO, // reset button switch
-+ MPP5_GPIO,
-+ MPP6_GPIO,
-+ MPP7_GPIO,
-+ MPP8_GPIO,
-+ MPP9_GIGE, /* GE_RXERR */
-+ MPP10_GPIO, // usb
-+ MPP11_GPIO, // usb
-+ MPP12_GIGE, // GE_TXD[4]
-+ MPP13_GIGE, // GE_TXD[5]
-+ MPP14_GIGE, // GE_TXD[6]
-+ MPP15_GIGE, // GE_TXD[7]
-+ MPP16_GIGE, // GE_RXD[4]
-+ MPP17_GIGE, // GE_RXD[5]
-+ MPP18_GIGE, // GE_RXD[6]
-+ MPP19_GIGE, // GE_RXD[7]
-+ 0,
-+};
-+
-+/*****************************************************************************
-+ * LEDS
-+ ****************************************************************************/
-+static struct platform_device dt2_leds = {
-+ .name = "dt2-led",
-+ .id = -1,
-+};
-+
-+/****************************************************************************
-+ * GPIO key
-+ ****************************************************************************/
-+static irqreturn_t dt2_reset_handler(int irq, void *dev_id)
-+{
-+ /* This is the paper-clip reset which does an emergency reboot. */
-+ printk(KERN_INFO "Restarting system.\n");
-+ machine_restart(NULL);
-+
-+ /* This should never be reached. */
-+ return IRQ_HANDLED;
-+}
-+
-+static irqreturn_t dt2_power_handler(int irq, void *dev_id)
-+{
-+ printk(KERN_INFO "Shutting down system.\n");
-+ machine_power_off();
-+ return IRQ_HANDLED;
-+}
-+
-+static void __init dt2_init(void)
-+{
-+ /*
-+ * Setup basic Orion functions. Need to be called early.
-+ */
-+ orion5x_init();
-+
-+ orion5x_mpp_conf(dt2_mpp_modes);
-+
-+ /*
-+ * Configure peripherals.
-+ */
-+
-+ orion5x_uart0_init();
-+ orion5x_ehci0_init();
-+ orion5x_ehci1_init();
-+ orion5x_i2c_init();
-+ orion5x_sata_init(&dt2_sata_data);
-+ orion5x_xor_init();
-+
-+ printk(KERN_INFO "U-Boot parameters:\n");
-+ printk(KERN_INFO "Sys Clk = %d, Tclk = %d, BoardID = 0x%02x\n", mvSysclk, mvTclk, gBoardId);
-+
-+ printk(KERN_INFO "Serial: %s\n", dt2_eeprom.fc.dt2_serial_number);
-+ printk(KERN_INFO "Revision: %016x\n", dt2_eeprom.fc.dt2_revision);
-+ printk(KERN_INFO "DT2: Using MAC address %pM for port 0\n",
-+ dt2_eeprom.gw.mac_addr[0]);
-+ printk(KERN_INFO "DT2: Using MAC address %pM for port 1\n",
-+ dt2_eeprom.gw.mac_addr[1]);
-+
-+ orion5x_eth_init(&dt2_eth_data);
-+ memcpy(dt2_eth_data.mac_addr, dt2_eeprom.gw.mac_addr[0], 6);
-+ orion5x_eth_switch_init(&dt2_switch_chip_data);
-+
-+ i2c_register_board_info(0, &dt2_i2c_rtc, 1);
-+
-+ mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
-+ ORION_MBUS_DEVBUS_BOOT_ATTR,
-+ DT2_NOR_BOOT_BASE, DT2_NOR_BOOT_SIZE);
-+
-+ platform_device_register(&dt2_nor_flash);
-+
-+ mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_TARGET(0),
-+ ORION_MBUS_DEVBUS_ATTR(0),
-+ DT2_LEDS_BASE, DT2_LEDS_SIZE);
-+ platform_device_register(&dt2_leds);
-+
-+ if (request_irq(gpio_to_irq(DT2_PIN_GPIO_RESET), &dt2_reset_handler,
-+ IRQF_TRIGGER_LOW,
-+ "DT2: Reset button", NULL) < 0) {
-+
-+ printk("DT2: Reset Button IRQ %d not available\n",
-+ gpio_to_irq(DT2_PIN_GPIO_RESET));
-+ }
-+
-+ if (request_irq(gpio_to_irq(DT2_PIN_GPIO_POWER), &dt2_power_handler,
-+ IRQF_TRIGGER_LOW,
-+ "DT2: Power button", NULL) < 0) {
-+
-+ printk(KERN_DEBUG "DT2: Power Button IRQ %d not available\n",
-+ gpio_to_irq(DT2_PIN_GPIO_POWER));
-+ }
-+}
-+
-+static int __init parse_tag_dt2_uboot(const struct tag *t)
-+{
-+ struct tag_mv_uboot *mv_uboot;
-+
-+ // Get pointer to our block
-+ mv_uboot = (struct tag_mv_uboot*)&t->u;
-+ mvTclk = mv_uboot->tclk;
-+ mvSysclk = mv_uboot->sysclk;
-+ mvUbootVer = mv_uboot->uboot_version;
-+ mvIsUsbHost = mv_uboot->isUsbHost;
-+
-+ // Some clock fixups
-+ if(mvTclk == 166000000) mvTclk = 166666667;
-+ else if(mvTclk == 133000000) mvTclk = 133333333;
-+ else if(mvSysclk == 166000000) mvSysclk = 166666667;
-+
-+ gBoardId = (mvUbootVer & 0xff);
-+
-+ //DT2 specific data
-+ memcpy(&dt2_eeprom, mv_uboot->dt2_eeprom, sizeof(struct DT2_EEPROM_STRUCT));
-+
-+ return 0;
-+}
-+__tagtable(ATAG_MV_UBOOT, parse_tag_dt2_uboot);
-+
-+/*
-+ * This is OpenWrt specific fixup. It includes code from original "tag_fixup_mem32" to
-+ * fixup bogus memory tags and also fixes kernel cmdline by adding " init=/etc/preinit"
-+ * at the end. It is important to flash OpenWrt image from original Freecom firmware.
-+ *
-+ * Vanilla kernel should use "tag_fixup_mem32" function.
-+ */
-+static void __init openwrt_fixup(struct tag *t, char **from)
-+{
-+ char *p = NULL;
-+ static char openwrt_init_tag[] __initdata = " init=/etc/preinit";
-+
-+ for (; t->hdr.size; t = tag_next(t)){
-+ /* Locate the Freecom cmdline */
-+ if (t->hdr.tag == ATAG_CMDLINE) {
-+ p = t->u.cmdline.cmdline;
-+ printk("%s(%d): Found cmdline '%s' at 0x%0lx\n",
-+ __FUNCTION__, __LINE__, p, (unsigned long)p);
-+ }
-+ /*
-+ * Many orion-based systems have buggy bootloader implementations.
-+ * This is a common fixup for bogus memory tags.
-+ */
-+ if (t->hdr.tag == ATAG_MEM &&
-+ (!t->u.mem.size || t->u.mem.size & ~PAGE_MASK ||
-+ t->u.mem.start & ~PAGE_MASK)) {
-+ printk(KERN_WARNING
-+ "Clearing invalid memory bank %dKB@0x%08x\n",
-+ t->u.mem.size / 1024, t->u.mem.start);
-+ t->hdr.tag = 0;
-+ }
-+ }
-+
-+ printk("%s(%d): End of table at 0x%0lx\n", __FUNCTION__, __LINE__, (unsigned long)t);
-+
-+ /* Overwrite the end of the table with a new cmdline tag. */
-+ t->hdr.tag = ATAG_CMDLINE;
-+ t->hdr.size =
-+ (sizeof (struct tag_header) +
-+ strlen(p) + strlen(openwrt_init_tag) + 1 + 4) >> 2;
-+
-+ strlcpy(t->u.cmdline.cmdline, p, COMMAND_LINE_SIZE);
-+ strlcpy(t->u.cmdline.cmdline + strlen(p), openwrt_init_tag,
-+ COMMAND_LINE_SIZE - strlen(p));
-+
-+ printk("%s(%d): New cmdline '%s' at 0x%0lx\n",
-+ __FUNCTION__, __LINE__,
-+ t->u.cmdline.cmdline, (unsigned long)t->u.cmdline.cmdline);
-+
-+ t = tag_next(t);
-+
-+ printk("%s(%d): New end of table at 0x%0lx\n", __FUNCTION__, __LINE__, (unsigned long)t);
-+
-+ t->hdr.tag = ATAG_NONE;
-+ t->hdr.size = 0;
-+}
-+
-+/* Warning: Freecom uses their own custom bootloader with mach-type (=1500) */
-+MACHINE_START(DT2, "Freecom DataTank Gateway")
-+ /* Maintainer: Zintis Petersons <Zintis.Petersons@abcsolutions.lv> */
-+ .atag_offset = 0x100,
-+ .init_machine = dt2_init,
-+ .map_io = orion5x_map_io,
-+ .init_irq = orion5x_init_irq,
-+ .init_time = orion5x_timer_init,
-+ .fixup = openwrt_fixup, //tag_fixup_mem32,
-+MACHINE_END
+++ /dev/null
---- a/arch/arm/mach-orion5x/Kconfig
-+++ b/arch/arm/mach-orion5x/Kconfig
-@@ -150,10 +150,13 @@ config MACH_MSS2_DT
- Maxtor Shared Storage II platform.
-
- config MACH_WNR854T
-- bool "Netgear WNR854T"
-+ bool "Netgear WNR854T / WN802T"
- help
- Say 'Y' here if you want your kernel to support the
-- Netgear WNR854T platform.
-+ Netgear WNR854T or WN802T platform.
-+
-+config MACH_WN802T
-+ def_bool MACH_WNR854T
-
- config MACH_RD88F5181L_GE
- bool "Marvell Orion-VoIP GE Reference Design"
---- a/arch/arm/mach-orion5x/wnr854t-setup.c
-+++ b/arch/arm/mach-orion5x/wnr854t-setup.c
-@@ -110,6 +110,11 @@ static struct dsa_chip_data wnr854t_swit
- .port_names[7] = "lan2",
- };
-
-+static struct dsa_chip_data wn802t_switch_chip_data = {
-+ .port_names[2] = "wan",
-+ .port_names[3] = "cpu",
-+};
-+
- static void __init wnr854t_init(void)
- {
- /*
-@@ -123,7 +128,10 @@ static void __init wnr854t_init(void)
- * Configure peripherals.
- */
- orion5x_eth_init(&wnr854t_eth_data);
-- orion5x_eth_switch_init(&wnr854t_switch_chip_data);
-+ if (machine_is_wn802t())
-+ orion5x_eth_switch_init(&wn802t_switch_chip_data);
-+ else
-+ orion5x_eth_switch_init(&wnr854t_switch_chip_data);
- orion5x_uart0_init();
-
- mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
-@@ -163,7 +171,7 @@ static struct hw_pci wnr854t_pci __initd
-
- static int __init wnr854t_pci_init(void)
- {
-- if (machine_is_wnr854t())
-+ if (machine_is_wnr854t() || machine_is_wn802t())
- pci_common_init(&wnr854t_pci);
-
- return 0;
-@@ -177,6 +185,18 @@ MACHINE_START(WNR854T, "Netgear WNR854T"
- .init_machine = wnr854t_init,
- .map_io = orion5x_map_io,
- .init_early = orion5x_init_early,
-+ .init_irq = orion5x_init_irq,
-+ .init_time = orion5x_timer_init,
-+ .fixup = tag_fixup_mem32,
-+ .restart = orion5x_restart,
-+MACHINE_END
-+
-+MACHINE_START(WN802T, "Netgear WN802T")
-+ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
-+ .atag_offset = 0x100,
-+ .init_machine = wnr854t_init,
-+ .map_io = orion5x_map_io,
-+ .init_early = orion5x_init_early,
- .init_irq = orion5x_init_irq,
- .init_time = orion5x_timer_init,
- .fixup = tag_fixup_mem32,
projects / openwrt / staging / chunkeey.git / commitdiff