target/linux/ramips/dts/mt7620a_ralink_mt7620a-evb.dts

   1 /dts-v1/;
   2
   3 #include "mt7620a.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         compatible = "ralink,mt7620a-evb", "ralink,mt7620a-soc";
  10         model = "Ralink MT7620a + MT7610e evaluation board";
  11
  12         keys {
  13                 compatible = "gpio-keys";
  14
  15                 s2 {
  16                         label = "S2";
  17                         gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
  18                         linux,code = <BTN_0>;
  19                 };
  20
  21                 s3 {
  22                         label = "S3";
  23                         gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
  24                         linux,code = <BTN_1>;
  25                 };
  26         };
  27 };
  28
  29 &spi0 {
  30         status = "okay";
  31
  32         m25p80@0 {
  33                 compatible = "jedec,spi-nor";
  34                 reg = <0>;
  35                 spi-max-frequency = <10000000>;
  36
  37                 partitions {
  38                         compatible = "fixed-partitions";
  39                         #address-cells = <1>;
  40                         #size-cells = <1>;
  41
  42                         partition@0 {
  43                                 label = "u-boot";
  44                                 reg = <0x0 0x30000>;
  45                                 read-only;
  46                         };
  47
  48                         partition@30000 {
  49                                 label = "u-boot-env";
  50                                 reg = <0x30000 0x10000>;
  51                                 read-only;
  52                         };
  53
  54                         factory: partition@40000 {
  55                                 label = "factory";
  56                                 reg = <0x40000 0x10000>;
  57                                 read-only;
  58                         };
  59
  60                         partition@50000 {
  61                                 compatible = "denx,uimage";
  62                                 label = "firmware";
  63                                 reg = <0x50000 0x7b0000>;
  64                         };
  65                 };
  66         };
  67 };
  68
  69 &pinctrl {
  70         state_default: pinctrl0 {
  71                 gpio {
  72                         ralink,group = "i2c", "uartf";
  73                         ralink,function = "gpio";
  74                 };
  75         };
  76 };
  77
  78 &ethernet {
  79         status = "okay";
  80         pinctrl-names = "default";
  81         pinctrl-0 = <&rgmii1_pins &rgmii2_pins &mdio_pins>;
  82         mediatek,portmap = "llllw";
  83
  84         port@4 {
  85                 status = "okay";
  86                 phy-mode = "rgmii";
  87                 phy-handle = <&phy4>;
  88         };
  89
  90         port@5 {
  91                 status = "okay";
  92                 phy-mode = "rgmii";
  93                 phy-handle = <&phy5>;
  94         };
  95
  96         mdio-bus {
  97                 status = "okay";
  98
  99                 phy4: ethernet-phy@4 {
 100                         reg = <4>;
 101                         phy-mode = "rgmii";
 102                 };
 103
 104                 phy5: ethernet-phy@5 {
 105                         reg = <5>;
 106                         phy-mode = "rgmii";
 107                 };
 108         };
 109 };
 110
 111 &gsw {
 112         mediatek,port4 = "gmac";
 113 };
 114
 115 &sdhci {
 116         status = "okay";
 117 };
 118
 119 &pcie {
 120         status = "okay";
 121 };
 122
 123 &ehci {
 124         status = "okay";
 125 };
 126
 127 &ohci {
 128         status = "okay";
 129 };