target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v1.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include "qca955x.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         compatible = "openmesh,om5p-ac-v1", "qca,qca9558";
  10         model = "OpenMesh OM5P-AC v1";
  11
  12         chosen {
  13                 /delete-property/ bootargs;
  14         };
  15
  16         aliases {
  17                 serial0 = &uart;
  18                 led-boot = &led_power_blue;
  19                 led-failsafe = &led_power_blue;
  20                 led-running = &led_power_blue;
  21                 led-upgrade = &led_power_blue;
  22                 label-mac-device = &eth0;
  23         };
  24
  25         leds {
  26                 compatible = "gpio-leds";
  27
  28                 led_power_blue: power_blue {
  29                         label = "blue:power";
  30                         gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
  31                         default-state = "on";
  32                 };
  33
  34                 wan_blue {
  35                         label = "blue:wan";
  36                         gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
  37                 };
  38
  39                 lan_blue {
  40                         label = "blue:lan";
  41                         gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
  42                 };
  43
  44                 wifi_green {
  45                         label = "green:wifi";
  46                         gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
  47                         linux,default-trigger = "phy0tpt";
  48                 };
  49
  50                 wifi_yellow {
  51                         label = "yellow:wifi";
  52                         gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
  53                 };
  54
  55                 wifi_red {
  56                         label = "red:wifi";
  57                         gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
  58                 };
  59         };
  60
  61         i2c {
  62                 compatible = "i2c-gpio";
  63                 gpios = <&gpio 11 GPIO_ACTIVE_HIGH /* sda */
  64                          &gpio 12 GPIO_ACTIVE_HIGH /* scl */
  65                         >;
  66                 #address-cells = <1>;
  67                 #size-cells = <0>;
  68
  69                 i2c-gpio,scl-open-drain;
  70                 i2c-gpio,sda-open-drain;
  71
  72                 tmp423a@4c {
  73                         compatible = "ti,tmp423";
  74                         reg = <0x4c>;
  75                 };
  76         };
  77
  78         watchdog {
  79                 compatible = "linux,wdt-gpio";
  80                 gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
  81                 hw_algo = "toggle";
  82                 /* hw_margin_ms is actually 300s but driver limits it to 60s */
  83                 hw_margin_ms = <60000>;
  84                 always-running;
  85         };
  86 };
  87
  88 &spi {
  89         status = "okay";
  90
  91         flash@0 {
  92                 compatible = "jedec,spi-nor";
  93                 reg = <0>;
  94                 spi-max-frequency = <40000000>;
  95
  96                 /* partitions are passed via bootloader */
  97                 partitions {
  98                         compatible = "fixed-partitions";
  99                         #address-cells = <1>;
 100                         #size-cells = <1>;
 101
 102                         partition@0 {
 103                                 label = "u-boot";
 104                                 reg = <0x000000 0x040000>;
 105                                 read-only;
 106                         };
 107
 108                         partition@40000 {
 109                                 label = "u-boot-env";
 110                                 reg = <0x040000 0x010000>;
 111                         };
 112
 113                         partition@50000 {
 114                                 label = "custom";
 115                                 reg = <0x050000 0x060000>;
 116                                 read-only;
 117                         };
 118
 119                         partition@b0000 {
 120                                 label = "inactive";
 121                                 reg = <0x0b0000 0x7a0000>;
 122                         };
 123
 124                         partition@850000 {
 125                                 label = "inactive2";
 126                                 reg = <0x850000 0x7a0000>;
 127                         };
 128
 129                         art: partition@ff0000 {
 130                                 label = "ART";
 131                                 reg = <0xff0000 0x010000>;
 132                                 read-only;
 133
 134                                 nvmem-layout {
 135                                         compatible = "fixed-layout";
 136                                         #address-cells = <1>;
 137                                         #size-cells = <1>;
 138
 139                                         macaddr_art_0: macaddr@0 {
 140                                                 compatible = "mac-base";
 141                                                 reg = <0x0 0x6>;
 142                                                 #nvmem-cell-cells = <1>;
 143                                         };
 144
 145                                         macaddr_art_6: macaddr@6 {
 146                                                 reg = <0x6 0x6>;
 147                                         };
 148
 149                                         cal_art_5000: calibration@5000 {
 150                                                 reg = <0x5000 0x844>;
 151                                         };
 152                                 };
 153                         };
 154                 };
 155         };
 156 };
 157
 158 &mdio0 {
 159         status = "okay";
 160
 161         phy1: ethernet-phy@1 {
 162                 reg = <1>;
 163                 eee-broken-100tx;
 164                 eee-broken-1000t;
 165         };
 166
 167         phy2: ethernet-phy@2 {
 168                 reg = <2>;
 169                 eee-broken-100tx;
 170                 eee-broken-1000t;
 171                 at803x-override-sgmii-link-check;
 172         };
 173 };
 174
 175 &eth0 {
 176         status = "okay";
 177
 178         pll-data = <0x82000101 0x80000101 0x80001313>;
 179
 180         nvmem-cells = <&macaddr_art_0 0>;
 181         nvmem-cell-names = "mac-address";
 182
 183         phy-mode = "rgmii-id";
 184         phy-handle = <&phy1>;
 185
 186         gmac-config {
 187                 device = <&gmac>;
 188                 rgmii-enabled = <1>;
 189                 rxd-delay = <3>;
 190                 rxdv-delay = <3>;
 191                 txd-delay = <0>;
 192                 txen-delay = <0>;
 193         };
 194 };
 195
 196 &eth1 {
 197         status = "okay";
 198
 199         pll-data = <0x03000101 0x80000101 0x80001313>;
 200
 201         nvmem-cells = <&macaddr_art_6>;
 202         nvmem-cell-names = "mac-address";
 203
 204         qca955x-sgmii-fixup;
 205
 206         phy-handle = <&phy2>;
 207 };
 208
 209 &wmac {
 210         status = "okay";
 211
 212         mtd-cal-data = <&art 0x1000>;
 213         nvmem-cells = <&macaddr_art_0 2>;
 214         nvmem-cell-names = "mac-address";
 215 };
 216
 217 &pcie1 {
 218         status = "okay";
 219
 220         wifi@0,0 {
 221                 compatible = "qcom,ath10k";
 222                 reg = <0x0000 0 0 0 0>;
 223                 nvmem-cells = <&cal_art_5000>, <&macaddr_art_0 16>;
 224                 nvmem-cell-names = "calibration", "mac-address";
 225         };
 226 };