1 // SPDX-License-Identifier: GPL-2.0-only OR MIT
3 #include "qcom-ipq4019.dtsi"
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/input/input.h>
6 #include <dt-bindings/soc/qcom,tcsr.h>
10 device_type = "memory";
11 reg = <0x80000000 0x10000000>;
16 compatible = "qcom,qca-gcnt";
21 compatible = "qcom,tcsr";
22 reg = <0x1953000 0x1000>;
23 qcom,ess-interface-select = <TCSR_ESS_PSGMII_RGMII5>;
27 compatible = "qcom,tcsr";
28 reg = <0x1949000 0x100>;
29 qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
33 compatible = "qcom,tcsr";
34 reg = <0x1957000 0x100>;
35 qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
40 compatible = "gpio-keys";
43 label = "Reset button";
44 gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
45 linux,code = <KEY_RESTART>;
67 /* Texas Instruments CC2540T BLE radio */
68 pinctrl-0 = <&serial_0_pins>;
69 pinctrl-names = "default";
74 pinctrl-0 = <&serial_1_pins>;
75 pinctrl-names = "default";
80 pinctrl-0 = <&i2c_0_pins>;
81 pinctrl-names = "default";
86 compatible = "atmel,at97sc3203";
101 mdio_pins: mdio_pinmux {
114 nand_pins: nand_pins {
116 pins = "gpio53", "gpio58", "gpio59";
122 pins = "gpio54", "gpio55", "gpio56",
123 "gpio57", "gpio60", "gpio61",
124 "gpio62", "gpio63", "gpio64",
125 "gpio65", "gpio66", "gpio67",
132 spi_0_pins: spi_0_pinmux {
134 function = "blsp_spi0";
135 pins = "gpio13", "gpio14", "gpio15";
136 drive-strength = <12>;
142 drive-strength = <2>;
148 i2c_0_pins: i2c_0_pinmux {
150 pins = "gpio10", "gpio11";
151 function = "blsp_i2c0";
152 drive-strength = <4>;
157 serial_0_pins: serial_0_pinmux {
159 pins = "gpio16", "gpio17";
160 function = "blsp_uart0";
165 serial_1_pins: serial_1_pinmux {
167 pins = "gpio8", "gpio9";
168 function = "blsp_uart1";
175 pinctrl-0 = <&nand_pins>;
176 pinctrl-names = "default";
181 compatible = "fixed-partitions";
182 #address-cells = <1>;
186 /* 'aos0' in Aruba firmware */
188 reg = <0x0 0x2000000>;
193 /* 'aos1' in Aruba firmware */
195 reg = <0x2000000 0x2000000>;
199 label = "aruba-ubifs";
200 reg = <0x4000000 0x4000000>;
209 pinctrl-0 = <&mdio_pins>;
210 pinctrl-names = "default";
212 ethphy: ethernet-phy@5 {
224 /delete-property/ psgmii-ethphy;
231 phy-handle = <ðphy>;
232 phy-mode = "rgmii-id";
265 nvmem-cell-names = "pre-calibration", "mac-address";
266 nvmem-cells = <&precal_art_1000>, <&macaddr_mfginfo_1d 0>;
267 qcom,ath10k-calibration-variant = "Aruba-AP-303";
272 nvmem-cell-names = "pre-calibration", "mac-address";
273 nvmem-cells = <&precal_art_5000>, <&macaddr_mfginfo_1d 1>;
274 qcom,ath10k-calibration-variant = "Aruba-AP-303";