1 #include "qcom-ipq8065-v1.0.dtsi"
3 #include <dt-bindings/input/input.h>
6 model = "ZyXEL NBG6817";
7 compatible = "zyxel,nbg6817", "qcom,ipq8065";
10 reg = <0x42000000 0x1e000000>;
11 device_type = "memory";
19 reg = <0x41200000 0x300000>;
30 led-failsafe = &power;
36 bootargs = "root=/dev/mmcblk0p5 rootfstype=squashfs,ext4 rootwait noinitrd";
37 linux,stdout-path = "serial0:115200n8";
42 button_pins: button_pins {
44 pins = "gpio6", "gpio54", "gpio65";
51 i2c4_pins: i2c4_pinmux {
53 pins = "gpio12", "gpio13";
55 drive-strength = <12>;
62 pins = "gpio26", "gpio33", "gpio64";
76 mdio0_pins: mdio0_pins {
78 pins = "gpio0", "gpio1";
90 rgmii2_pins: rgmii2_pins {
92 pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
93 "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
100 pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
107 pins = "gpio18", "gpio19", "gpio21";
109 drive-strength = <10>;
115 drive-strength = <12>;
119 usb0_pwr_en_pins: usb0_pwr_en_pins {
123 drive-strength = <12>;
131 drive-strength = <12>;
137 usb1_pwr_en_pins: usb1_pwr_en_pins {
141 drive-strength = <12>;
149 drive-strength = <12>;
157 qcom,mode = <GSBI_PROT_I2C_UART>;
163 * The i2c device on gsbi4 should not be enabled.
164 * On ipq806x designs gsbi4 i2c is meant for exclusive
165 * RPM usage. Turning this on in kernel manifests as
166 * i2c failure for the RPM.
170 gsbi5: gsbi@1a200000 {
171 qcom,mode = <GSBI_PROT_SPI>;
176 spi-max-frequency = <50000000>;
177 pinctrl-0 = <&spi_pins>;
178 pinctrl-names = "default";
180 cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
183 compatible = "s25fl512s";
184 #address-cells = <1>;
186 spi-max-frequency = <51200000>;
189 linux,part-probe = "qcom-smem";
194 phy@100f8800 { /* USB3 port 1 HS phy */
198 phy@100f8830 { /* USB3 port 1 SS phy */
202 phy@110f8800 { /* USB3 port 0 HS phy */
206 phy@110f8830 { /* USB3 port 0 SS phy */
213 pinctrl-0 = <&usb0_pwr_en_pins>;
214 pinctrl-names = "default";
220 pinctrl-0 = <&usb1_pwr_en_pins>;
221 pinctrl-names = "default";
224 pcie0: pci@1b500000 {
226 reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
227 pinctrl-0 = <&pcie0_pins>;
228 pinctrl-names = "default";
231 pcie1: pci@1b700000 {
233 reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
234 pinctrl-0 = <&pcie1_pins>;
235 pinctrl-names = "default";
239 compatible = "virtual,mdio-gpio";
240 #address-cells = <1>;
242 gpios = <&qcom_pinmux 1 GPIO_ACTIVE_LOW &qcom_pinmux 0 GPIO_ACTIVE_LOW>;
243 pinctrl-0 = <&mdio0_pins>;
244 pinctrl-names = "default";
246 phy0: ethernet-phy@0 {
247 device_type = "ethernet-phy";
249 qca,ar8327-initvals = <
250 0x00004 0x7600000 /* PAD0_MODE */
251 0x00008 0x1000000 /* PAD5_MODE */
252 0x0000c 0x80 /* PAD6_MODE */
253 0x000e4 0xaa545 /* MAC_POWER_SEL */
254 0x000e0 0xc74164de /* SGMII_CTRL */
255 0x0007c 0x4e /* PORT0_STATUS */
256 0x00094 0x4e /* PORT6_STATUS */
257 0x00970 0x1e864443 /* QM_PORT0_CTRL0 */
258 0x00974 0x000001c6 /* QM_PORT0_CTRL1 */
259 0x00978 0x19008643 /* QM_PORT1_CTRL0 */
260 0x0097c 0x000001c6 /* QM_PORT1_CTRL1 */
261 0x00980 0x19008643 /* QM_PORT2_CTRL0 */
262 0x00984 0x000001c6 /* QM_PORT2_CTRL1 */
263 0x00988 0x19008643 /* QM_PORT3_CTRL0 */
264 0x0098c 0x000001c6 /* QM_PORT3_CTRL1 */
265 0x00990 0x19008643 /* QM_PORT4_CTRL0 */
266 0x00994 0x000001c6 /* QM_PORT4_CTRL1 */
267 0x00998 0x1e864443 /* QM_PORT5_CTRL0 */
268 0x0099c 0x000001c6 /* QM_PORT5_CTRL1 */
269 0x009a0 0x1e864443 /* QM_PORT6_CTRL0 */
270 0x009a4 0x000001c6 /* QM_PORT6_CTRL1 */
274 phy4: ethernet-phy@4 {
275 device_type = "ethernet-phy";
277 qca,ar8327-initvals = <
278 0x000e4 0x6a545 /* MAC_POWER_SEL */
279 0x0000c 0x80 /* PAD6_MODE */
284 gmac1: ethernet@37200000 {
288 qcom,phy_mdio_addr = <4>;
289 qcom,poll_required = <0>;
290 qcom,rgmii_delay = <1>;
291 qcom,phy_mii_type = <0>;
292 qcom,emulation = <0>;
296 pinctrl-0 = <&rgmii2_pins>;
297 pinctrl-names = "default";
305 gmac2: ethernet@37400000 {
309 qcom,phy_mdio_addr = <0>; /* none */
310 qcom,poll_required = <0>; /* no polling */
311 qcom,rgmii_delay = <0>;
312 qcom,phy_mii_type = <1>;
313 qcom,emulation = <0>;
324 pinctrl-0 = <&i2c4_pins>;
325 pinctrl-names = "default";
329 sdcc1: sdcc@12400000 {
331 dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
332 dma-names = "tx", "rx";
338 compatible = "gpio-keys";
339 pinctrl-0 = <&button_pins>;
340 pinctrl-names = "default";
344 gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
345 linux,code = <KEY_RFKILL>;
350 gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
351 linux,code = <KEY_RESTART>;
356 gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
357 linux,code = <KEY_WPS_BUTTON>;
362 compatible = "gpio-leds";
363 pinctrl-0 = <&led_pins>;
364 pinctrl-names = "default";
367 label = "nbg6817:white:internet";
368 gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
372 label = "nbg6817:white:power";
373 gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
377 label = "nbg6817:amber:wifi";
378 gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
382 label = "nbg6817:amber:wifi5g";
383 gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;