1 #include "qcom-ipq8065-smb208.dtsi"
3 #include <dt-bindings/input/input.h>
6 model = "ZyXEL NBG6817";
7 compatible = "zyxel,nbg6817", "qcom,ipq8065", "qcom,ipq8064";
10 reg = <0x42000000 0x1e000000>;
11 device_type = "memory";
19 led-failsafe = &power;
25 bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd fstools_ignore_partname=1";
26 append-rootblock = "root=/dev/mmcblk0p";
30 compatible = "gpio-keys";
31 pinctrl-0 = <&button_pins>;
32 pinctrl-names = "default";
36 gpios = <&qcom_pinmux 53 GPIO_ACTIVE_LOW>;
37 linux,code = <KEY_RFKILL>;
38 linux,input-type = <EV_SW>;
39 debounce-interval = <60>;
45 gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
46 linux,code = <KEY_RESTART>;
47 debounce-interval = <60>;
53 gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
54 linux,code = <KEY_WPS_BUTTON>;
55 debounce-interval = <60>;
61 compatible = "gpio-leds";
62 pinctrl-0 = <&led_pins>;
63 pinctrl-names = "default";
66 label = "white:internet";
67 gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
71 label = "white:power";
72 gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
73 default-state = "keep";
77 label = "amber:wifi2g";
78 gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
81 /* wifi2g amber from the manual is missing */
84 label = "amber:wifi5g";
85 gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
88 /* wifi5g amber from the manual is missing */
93 button_pins: button_pins {
95 pins = "gpio53", "gpio54", "gpio65";
104 pins = "gpio9", "gpio26", "gpio33", "gpio64";
106 drive-strength = <2>;
111 mdio0_pins: mdio0-pins {
118 rgmii2_pins: rgmii2-pins {
120 pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
128 drive-strength = <12>;
132 usb0_pwr_en_pins: usb0_pwr_en_pins {
134 pins = "gpio16", "gpio17";
136 drive-strength = <12>;
151 usb1_pwr_en_pins: usb1_pwr_en_pins {
153 pins = "gpio14", "gpio15";
155 drive-strength = <12>;
172 qcom,mode = <GSBI_PROT_SPI>;
178 pinctrl-0 = <&spi_pins>;
179 pinctrl-names = "default";
181 cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
184 compatible = "jedec,spi-nor";
185 #address-cells = <1>;
187 spi-max-frequency = <51200000>;
191 compatible = "qcom,smem-part";
208 pinctrl-0 = <&usb0_pwr_en_pins>;
209 pinctrl-names = "default";
223 pinctrl-0 = <&usb1_pwr_en_pins>;
224 pinctrl-names = "default";
229 reset-gpios = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
230 pinctrl-0 = <&pcie0_pins>;
231 pinctrl-names = "default";
236 reset-gpios = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
237 pinctrl-0 = <&pcie1_pins>;
238 pinctrl-names = "default";
239 max-link-speed = <1>;
245 pinctrl-0 = <&mdio0_pins>;
246 pinctrl-names = "default";
249 compatible = "qca,qca8337";
250 #address-cells = <1>;
255 #address-cells = <1>;
263 tx-internal-delay-ps = <1000>;
264 rx-internal-delay-ps = <1000>;
275 phy-mode = "internal";
276 phy-handle = <&phy_port1>;
282 phy-mode = "internal";
283 phy-handle = <&phy_port2>;
289 phy-mode = "internal";
290 phy-handle = <&phy_port3>;
296 phy-mode = "internal";
297 phy-handle = <&phy_port4>;
303 phy-mode = "internal";
304 phy-handle = <&phy_port5>;
312 qca,sgmii-enable-pll;
322 #address-cells = <1>;
352 qcom,phy_mdio_addr = <4>;
353 qcom,poll_required = <0>;
354 qcom,rgmii_delay = <1>;
355 qcom,phy_mii_type = <0>;
356 qcom,emulation = <0>;
360 pinctrl-0 = <&rgmii2_pins>;
361 pinctrl-names = "default";
373 qcom,phy_mdio_addr = <0>; /* none */
374 qcom,poll_required = <0>; /* no polling */
375 qcom,rgmii_delay = <0>;
376 qcom,phy_mii_type = <1>;
377 qcom,emulation = <0>;