1 #include "qcom-ipq8064-v2.0.dtsi"
3 #include <dt-bindings/input/input.h>
6 model = "Netgear Nighthawk X4 R7500v2";
7 compatible = "netgear,r7500v2", "qcom,ipq8064";
10 reg = <0x42000000 0x1e000000>;
11 device_type = "memory";
19 reg = <0x41200000 0x300000>;
24 reg = <0x5fe00000 0x200000>;
30 serial0 = &gsbi4_serial;
34 led-failsafe = &power;
40 bootargs = "rootfstype=squashfs noinitrd";
41 stdout-path = "serial0:115200n8";
46 button_pins: button_pins {
48 pins = "gpio6", "gpio54", "gpio65";
55 i2c4_pins: i2c4_pinmux {
57 pins = "gpio12", "gpio13";
59 drive-strength = <12>;
66 pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
67 "gpio24","gpio26", "gpio53", "gpio64";
74 mdio0_pins: mdio0_pins {
76 pins = "gpio0", "gpio1";
83 nand_pins: nand_pins {
85 pins = "gpio34", "gpio35", "gpio36",
88 drive-strength = <10>;
95 drive-strength = <10>;
100 pins = "gpio40", "gpio41", "gpio42",
101 "gpio43", "gpio44", "gpio45",
104 drive-strength = <10>;
109 rgmii2_pins: rgmii2_pins {
111 pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
112 "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
114 drive-strength = <8>;
119 usb0_pwr_en_pins: usb0_pwr_en_pins {
123 drive-strength = <12>;
129 usb1_pwr_en_pins: usb1_pwr_en_pins {
131 pins = "gpio16", "gpio68";
133 drive-strength = <12>;
141 qcom,mode = <GSBI_PROT_I2C_UART>;
147 * The i2c device on gsbi4 should not be enabled.
148 * On ipq806x designs gsbi4 i2c is meant for exclusive
149 * RPM usage. Turning this on in kernel manifests as
150 * i2c failure for the RPM.
162 usb3_0: usb3@110f8800 {
165 pinctrl-0 = <&usb0_pwr_en_pins>;
166 pinctrl-names = "default";
169 usb3_1: usb3@100f8800 {
172 pinctrl-0 = <&usb1_pwr_en_pins>;
173 pinctrl-names = "default";
176 pcie0: pci@1b500000 {
178 reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
179 pinctrl-0 = <&pcie0_pins>;
180 pinctrl-names = "default";
183 pcie1: pci@1b700000 {
185 reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
186 pinctrl-0 = <&pcie1_pins>;
187 pinctrl-names = "default";
194 pinctrl-0 = <&nand_pins>;
195 pinctrl-names = "default";
199 compatible = "qcom,nandcs";
201 nand-ecc-strength = <4>;
202 nand-bus-width = <8>;
203 nand-ecc-step-size = <512>;
206 compatible = "fixed-partitions";
207 #address-cells = <1>;
212 reg = <0x0000000 0x0c80000>;
218 reg = <0x0c80000 0x0500000>;
224 reg = <0x1180000 0x0080000>;
230 reg = <0x1200000 0x0140000>;
234 artbak: art@1340000 {
236 reg = <0x1340000 0x0140000>;
242 reg = <0x1480000 0x0400000>;
247 reg = <0x1880000 0x6080000>;
252 reg = <0x7900000 0x0700000>;
260 compatible = "virtual,mdio-gpio";
261 #address-cells = <1>;
263 gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
264 <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
265 pinctrl-0 = <&mdio0_pins>;
266 pinctrl-names = "default";
268 phy0: ethernet-phy@0 {
270 qca,ar8327-initvals = <
271 0x00004 0x7600000 /* PAD0_MODE */
272 0x00008 0x1000000 /* PAD5_MODE */
273 0x0000c 0x80 /* PAD6_MODE */
274 0x000e4 0xaa545 /* MAC_POWER_SEL */
275 0x000e0 0xc74164de /* SGMII_CTRL */
276 0x0007c 0x4e /* PORT0_STATUS */
277 0x00094 0x4e /* PORT6_STATUS */
281 phy4: ethernet-phy@4 {
286 gmac1: ethernet@37200000 {
291 pinctrl-0 = <&rgmii2_pins>;
292 pinctrl-names = "default";
294 mtd-mac-address = <&art 6>;
302 gmac2: ethernet@37400000 {
307 mtd-mac-address = <&art 0>;
317 compatible = "gpio-keys";
318 pinctrl-0 = <&button_pins>;
319 pinctrl-names = "default";
323 gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
324 linux,code = <KEY_RFKILL>;
329 gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
330 linux,code = <KEY_RESTART>;
335 gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
336 linux,code = <KEY_WPS_BUTTON>;
341 compatible = "gpio-leds";
342 pinctrl-0 = <&led_pins>;
343 pinctrl-names = "default";
346 label = "r7500v2:amber:usb1";
347 gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
351 label = "r7500v2:amber:usb3";
352 gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
356 label = "r7500v2:amber:status";
357 gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
361 label = "r7500v2:white:internet";
362 gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
366 label = "r7500v2:white:wan";
367 gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
371 label = "r7500v2:white:wps";
372 gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
376 label = "r7500v2:white:esata";
377 gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
381 label = "r7500v2:white:power";
382 gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
383 default-state = "keep";
387 label = "r7500v2:white:wifi";
388 gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;