3 #include <dt-bindings/clock/qcom,gcc-ipq806x.h>
4 #include <dt-bindings/mfd/qcom-rpm.h>
5 #include <dt-bindings/clock/qcom,rpmcc.h>
6 #include <dt-bindings/clock/qcom,lcc-ipq806x.h>
7 #include <dt-bindings/soc/qcom,gsbi.h>
8 #include <dt-bindings/reset/qcom,gcc-ipq806x.h>
9 #include <dt-bindings/interrupt-controller/arm-gic.h>
10 #include <dt-bindings/gpio/gpio.h>
13 model = "Qualcomm IPQ8064";
14 compatible = "qcom,ipq8064";
15 interrupt-parent = <&intc>;
19 memory { device_type = "memory"; reg = <0 0>; };
26 compatible = "qcom,krait";
27 enable-method = "qcom,kpss-acc-v1";
30 next-level-cache = <&L2>;
31 qcom,acc = <&acpu0_aux>;
33 clocks = <&kraitcc 0>, <&kraitcc 4>;
34 clock-names = "cpu", "l2";
35 clock-latency = <100000>;
36 cpu-supply = <&smb208_s2a>;
37 operating-points-v2 = <&opp_table0>;
38 voltage-tolerance = <5>;
39 cooling-min-state = <0>;
40 cooling-max-state = <10>;
42 cpu-idle-states = <&CPU_SPC>;
46 compatible = "qcom,krait";
47 enable-method = "qcom,kpss-acc-v1";
50 next-level-cache = <&L2>;
51 qcom,acc = <&acpu1_aux>;
53 clocks = <&kraitcc 1>, <&kraitcc 4>;
54 clock-names = "cpu", "l2";
55 clock-latency = <100000>;
56 cpu-supply = <&smb208_s2b>;
57 operating-points-v2 = <&opp_table0>;
58 voltage-tolerance = <5>;
59 cooling-min-state = <0>;
60 cooling-max-state = <10>;
62 cpu-idle-states = <&CPU_SPC>;
72 qcom,l2-rates = <384000000 1000000000 1200000000>;
73 qcom,l2-cpufreq = <384000000 600000000 1200000000>;
74 qcom,l2-volt = <1100000 1100000 1150000>;
75 qcom,l2-supply = <&smb208_s1a>;
80 compatible = "qcom,idle-state-spc",
83 entry-latency-us = <400>;
84 exit-latency-us = <900>;
85 min-residency-us = <3000>;
90 opp_table0: opp_table0 {
91 compatible = "operating-points-v2-qcom-cpu";
92 nvmem-cells = <&speedbin_efuse>;
95 opp-hz = /bits/ 64 <384000000>;
96 opp-microvolt-speed0-pvs0-v0 = <1000000>;
97 opp-microvolt-speed0-pvs1-v0 = <925000>;
98 opp-microvolt-speed0-pvs2-v0 = <875000>;
99 opp-microvolt-speed0-pvs3-v0 = <800000>;
100 opp-supported-hw = <0x1>;
101 clock-latency-ns = <100000>;
105 opp-hz = /bits/ 64 <600000000>;
106 opp-microvolt-speed0-pvs0-v0 = <1050000>;
107 opp-microvolt-speed0-pvs1-v0 = <975000>;
108 opp-microvolt-speed0-pvs2-v0 = <925000>;
109 opp-microvolt-speed0-pvs3-v0 = <850000>;
110 opp-supported-hw = <0x1>;
111 clock-latency-ns = <100000>;
115 opp-hz = /bits/ 64 <800000000>;
116 opp-microvolt-speed0-pvs0-v0 = <1100000>;
117 opp-microvolt-speed0-pvs1-v0 = <1025000>;
118 opp-microvolt-speed0-pvs2-v0 = <995000>;
119 opp-microvolt-speed0-pvs3-v0 = <900000>;
120 opp-supported-hw = <0x1>;
121 clock-latency-ns = <100000>;
125 opp-hz = /bits/ 64 <1000000000>;
126 opp-microvolt-speed0-pvs0-v0 = <1150000>;
127 opp-microvolt-speed0-pvs1-v0 = <1075000>;
128 opp-microvolt-speed0-pvs2-v0 = <1025000>;
129 opp-microvolt-speed0-pvs3-v0 = <950000>;
130 opp-supported-hw = <0x1>;
131 clock-latency-ns = <100000>;
135 opp-hz = /bits/ 64 <1200000000>;
136 opp-microvolt-speed0-pvs0-v0 = <1200000>;
137 opp-microvolt-speed0-pvs1-v0 = <1125000>;
138 opp-microvolt-speed0-pvs2-v0 = <1075000>;
139 opp-microvolt-speed0-pvs3-v0 = <1000000>;
140 opp-supported-hw = <0x1>;
141 clock-latency-ns = <100000>;
145 opp-hz = /bits/ 64 <1400000000>;
146 opp-microvolt-speed0-pvs0-v0 = <1250000>;
147 opp-microvolt-speed0-pvs1-v0 = <1175000>;
148 opp-microvolt-speed0-pvs2-v0 = <1125000>;
149 opp-microvolt-speed0-pvs3-v0 = <1050000>;
150 opp-supported-hw = <0x1>;
151 clock-latency-ns = <100000>;
158 polling-delay-passive = <0>;
160 thermal-sensors = <&tsens 0>;
164 temperature = <125000>;
166 type = "critical_high";
170 temperature = <105000>;
172 type = "configurable_hi";
176 temperature = <95000>;
178 type = "configurable_lo";
184 type = "critical_low";
190 polling-delay-passive = <0>;
192 thermal-sensors = <&tsens 1>;
196 temperature = <125000>;
198 type = "critical_high";
202 temperature = <105000>;
204 type = "configurable_hi";
208 temperature = <95000>;
210 type = "configurable_lo";
216 type = "critical_low";
222 polling-delay-passive = <0>;
224 thermal-sensors = <&tsens 2>;
228 temperature = <125000>;
230 type = "critical_high";
234 temperature = <105000>;
236 type = "configurable_hi";
240 temperature = <95000>;
242 type = "configurable_lo";
248 type = "critical_low";
254 polling-delay-passive = <0>;
256 thermal-sensors = <&tsens 3>;
260 temperature = <125000>;
262 type = "critical_high";
266 temperature = <105000>;
268 type = "configurable_hi";
272 temperature = <95000>;
274 type = "configurable_lo";
280 type = "critical_low";
286 polling-delay-passive = <0>;
288 thermal-sensors = <&tsens 4>;
292 temperature = <125000>;
294 type = "critical_high";
298 temperature = <105000>;
300 type = "configurable_hi";
304 temperature = <95000>;
306 type = "configurable_lo";
312 type = "critical_low";
318 polling-delay-passive = <0>;
320 thermal-sensors = <&tsens 5>;
324 temperature = <125000>;
326 type = "critical_high";
330 temperature = <105000>;
332 type = "configurable_hi";
336 temperature = <95000>;
338 type = "configurable_lo";
344 type = "critical_low";
350 polling-delay-passive = <0>;
352 thermal-sensors = <&tsens 6>;
356 temperature = <125000>;
358 type = "critical_high";
362 temperature = <105000>;
364 type = "configurable_hi";
368 temperature = <95000>;
370 type = "configurable_lo";
376 type = "critical_low";
382 polling-delay-passive = <0>;
384 thermal-sensors = <&tsens 7>;
388 temperature = <125000>;
390 type = "critical_high";
394 temperature = <105000>;
396 type = "configurable_hi";
400 temperature = <95000>;
402 type = "configurable_lo";
408 type = "critical_low";
414 polling-delay-passive = <0>;
416 thermal-sensors = <&tsens 8>;
420 temperature = <125000>;
422 type = "critical_high";
426 temperature = <105000>;
428 type = "configurable_hi";
432 temperature = <95000>;
434 type = "configurable_lo";
440 type = "critical_low";
446 polling-delay-passive = <0>;
448 thermal-sensors = <&tsens 9>;
452 temperature = <125000>;
454 type = "critical_high";
458 temperature = <105000>;
460 type = "configurable_hi";
464 temperature = <95000>;
466 type = "configurable_lo";
472 type = "critical_low";
478 polling-delay-passive = <0>;
480 thermal-sensors = <&tsens 10>;
484 temperature = <125000>;
486 type = "critical_high";
490 temperature = <105000>;
492 type = "configurable_hi";
496 temperature = <95000>;
498 type = "configurable_lo";
504 type = "critical_low";
511 compatible = "qcom,krait-pmu";
512 interrupts = <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) |
513 IRQ_TYPE_LEVEL_HIGH)>;
517 #address-cells = <1>;
522 reg = <0x40000000 0x1000000>;
526 smem: smem@41000000 {
527 reg = <0x41000000 0x200000>;
534 compatible = "fixed-clock";
536 clock-frequency = <25000000>;
540 compatible = "fixed-clock";
542 clock-frequency = <25000000>;
545 sleep_clk: sleep_clk {
546 compatible = "fixed-clock";
547 clock-frequency = <32768>;
553 compatible = "qcom,fab-scaling";
554 clocks = <&rpmcc RPM_APPS_FABRIC_A_CLK>, <&rpmcc RPM_EBI1_A_CLK>;
555 clock-names = "apps-fab-clk", "ddr-fab-clk";
556 fab_freq_high = <533000000>;
557 fab_freq_nominal = <400000000>;
558 cpu_freq_threshold = <1000000000>;
563 compatible = "qcom,scm-ipq806x";
568 #address-cells = <1>;
571 compatible = "simple-bus";
574 compatible = "qcom,lpass-cpu";
576 clocks = <&lcc AHBIX_CLK>,
579 clock-names = "ahbix-clk",
582 interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>;
583 interrupt-names = "lpass-irq-lpaif";
584 reg = <0x28100000 0x10000>;
585 reg-names = "lpass-lpaif";
588 qfprom: qfprom@700000 {
589 compatible = "qcom,qfprom", "syscon";
590 reg = <0x700000 0x1000>;
591 #address-cells = <1>;
594 tsens_calib: calib@400 {
597 tsens_backup: backup@410 {
600 speedbin_efuse: speedbin@0c0 {
606 compatible = "qcom,rpm-ipq8064";
607 reg = <0x108000 0x1000>;
608 qcom,ipc = <&l2cc 0x8 2>;
610 interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
611 <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
612 <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
613 interrupt-names = "ack",
617 clocks = <&gcc RPM_MSG_RAM_H_CLK>;
620 #address-cells = <1>;
623 rpmcc: clock-controller {
624 compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
629 compatible = "qcom,rpm-smb208-regulators";
632 regulator-min-microvolt = <1050000>;
633 regulator-max-microvolt = <1150000>;
635 qcom,switch-mode-frequency = <1200000>;
640 regulator-min-microvolt = <1050000>;
641 regulator-max-microvolt = <1150000>;
643 qcom,switch-mode-frequency = <1200000>;
647 regulator-min-microvolt = < 800000>;
648 regulator-max-microvolt = <1250000>;
650 qcom,switch-mode-frequency = <1200000>;
654 regulator-min-microvolt = < 800000>;
655 regulator-max-microvolt = <1250000>;
657 qcom,switch-mode-frequency = <1200000>;
663 compatible = "qcom,prng";
664 reg = <0x1a500000 0x200>;
665 clocks = <&gcc PRNG_CLK>;
666 clock-names = "core";
669 qcom_pinmux: pinmux@800000 {
670 compatible = "qcom,ipq8064-pinctrl";
671 reg = <0x800000 0x4000>;
675 interrupt-controller;
676 #interrupt-cells = <2>;
677 interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
679 pcie0_pins: pcie0_pinmux {
682 function = "pcie1_rst";
683 drive-strength = <12>;
688 pcie1_pins: pcie1_pinmux {
691 function = "pcie2_rst";
692 drive-strength = <12>;
697 pcie2_pins: pcie2_pinmux {
700 function = "pcie3_rst";
701 drive-strength = <12>;
707 i2c4_pins: i2c4_pinmux {
709 pins = "gpio12", "gpio13";
711 drive-strength = <12>;
718 pins = "gpio18", "gpio19", "gpio21";
720 drive-strength = <10>;
725 nand_pins: nand_pins {
727 pins = "gpio34", "gpio35", "gpio36",
730 drive-strength = <10>;
737 drive-strength = <10>;
742 pins = "gpio40", "gpio41", "gpio42",
743 "gpio43", "gpio44", "gpio45",
746 drive-strength = <10>;
751 mdio0_pins: mdio0_pins {
753 pins = "gpio0", "gpio1";
755 drive-strength = <8>;
760 rgmii2_pins: rgmii2_pins {
762 pins = "gpio27", "gpio28", "gpio29",
763 "gpio30", "gpio31", "gpio32",
764 "gpio51", "gpio52", "gpio59",
765 "gpio60", "gpio61", "gpio62";
767 drive-strength = <8>;
772 leds_pins: leds_pins {
774 pins = "gpio7", "gpio8", "gpio9",
777 drive-strength = <2>;
783 buttons_pins: buttons_pins {
786 drive-strength = <2>;
792 intc: interrupt-controller@2000000 {
793 compatible = "qcom,msm-qgic2";
794 interrupt-controller;
795 #interrupt-cells = <3>;
796 reg = <0x02000000 0x1000>,
801 compatible = "qcom,kpss-timer", "qcom,msm-timer";
802 interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(2) |
803 IRQ_TYPE_EDGE_RISING)>,
804 <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(2) |
805 IRQ_TYPE_EDGE_RISING)>,
806 <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(2) |
807 IRQ_TYPE_EDGE_RISING)>,
808 <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(2) |
809 IRQ_TYPE_EDGE_RISING)>,
810 <GIC_PPI 5 (GIC_CPU_MASK_SIMPLE(2) |
811 IRQ_TYPE_EDGE_RISING)>;
812 reg = <0x0200a000 0x100>;
813 clock-frequency = <25000000>,
815 clocks = <&sleep_clk>;
816 clock-names = "sleep";
817 cpu-offset = <0x80000>;
820 acpu0_aux: clock-controller@2088000 {
821 compatible = "qcom,kpss-acc-v1";
822 reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
823 clock-output-names = "acpu0_aux";
826 acpu1_aux: clock-controller@2098000 {
827 compatible = "qcom,kpss-acc-v1";
828 reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
829 clock-output-names = "acpu1_aux";
832 l2cc: clock-controller@2011000 {
833 compatible = "qcom,kpss-gcc", "syscon";
834 reg = <0x2011000 0x1000>;
835 clock-output-names = "acpu_l2_aux";
838 kraitcc: clock-controller {
839 compatible = "qcom,krait-cc-v1";
843 saw0: regulator@2089000 {
844 compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon";
845 reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
849 saw1: regulator@2099000 {
850 compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon";
851 reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
855 saw_l2: regulator@02012000 {
856 compatible = "qcom,saw2", "syscon";
857 reg = <0x02012000 0x1000>;
861 sic_non_secure: sic-non-secure@12100000 {
862 compatible = "syscon";
863 reg = <0x12100000 0x10000>;
866 gsbi2: gsbi@12480000 {
867 compatible = "qcom,gsbi-v1.0.0";
869 reg = <0x12480000 0x100>;
870 clocks = <&gcc GSBI2_H_CLK>;
871 clock-names = "iface";
872 #address-cells = <1>;
877 syscon-tcsr = <&tcsr>;
879 uart2: serial@12490000 {
880 compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
881 reg = <0x12490000 0x1000>,
883 interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
884 clocks = <&gcc GSBI2_UART_CLK>, <&gcc GSBI2_H_CLK>;
885 clock-names = "core", "iface";
890 compatible = "qcom,i2c-qup-v1.1.1";
891 reg = <0x124a0000 0x1000>;
892 interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
894 clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
895 clock-names = "core", "iface";
898 #address-cells = <1>;
904 gsbi4: gsbi@16300000 {
905 compatible = "qcom,gsbi-v1.0.0";
907 reg = <0x16300000 0x100>;
908 clocks = <&gcc GSBI4_H_CLK>;
909 clock-names = "iface";
910 #address-cells = <1>;
915 syscon-tcsr = <&tcsr>;
917 gsbi4_serial: serial@16340000 {
918 compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
919 reg = <0x16340000 0x1000>,
921 interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
922 clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
923 clock-names = "core", "iface";
928 compatible = "qcom,i2c-qup-v1.1.1";
929 reg = <0x16380000 0x1000>;
930 interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
932 clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>;
933 clock-names = "core", "iface";
936 #address-cells = <1>;
941 gsbi5: gsbi@1a200000 {
942 compatible = "qcom,gsbi-v1.0.0";
944 reg = <0x1a200000 0x100>;
945 clocks = <&gcc GSBI5_H_CLK>;
946 clock-names = "iface";
947 #address-cells = <1>;
952 syscon-tcsr = <&tcsr>;
954 uart5: serial@1a240000 {
955 compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
956 reg = <0x1a240000 0x1000>,
958 interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
959 clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
960 clock-names = "core", "iface";
965 compatible = "qcom,i2c-qup-v1.1.1";
966 reg = <0x1a280000 0x1000>;
967 interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
969 clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
970 clock-names = "core", "iface";
973 #address-cells = <1>;
978 compatible = "qcom,spi-qup-v1.1.1";
979 reg = <0x1a280000 0x1000>;
980 interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
982 clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
983 clock-names = "core", "iface";
986 #address-cells = <1>;
991 gsbi7: gsbi@16600000 {
993 compatible = "qcom,gsbi-v1.0.0";
995 reg = <0x16600000 0x100>;
996 clocks = <&gcc GSBI7_H_CLK>;
997 clock-names = "iface";
998 #address-cells = <1>;
1001 syscon-tcsr = <&tcsr>;
1003 gsbi7_serial: serial@16640000 {
1004 compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
1005 reg = <0x16640000 0x1000>,
1006 <0x16600000 0x1000>;
1007 interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
1008 clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
1009 clock-names = "core", "iface";
1010 status = "disabled";
1014 sata_phy: sata-phy@1b400000 {
1015 compatible = "qcom,ipq806x-sata-phy";
1016 reg = <0x1b400000 0x200>;
1018 clocks = <&gcc SATA_PHY_CFG_CLK>;
1019 clock-names = "cfg";
1022 status = "disabled";
1025 sata: sata@29000000 {
1026 compatible = "qcom,ipq806x-ahci", "generic-ahci";
1027 reg = <0x29000000 0x180>;
1029 ports-implemented = <0x1>;
1031 interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
1033 clocks = <&gcc SFAB_SATA_S_H_CLK>,
1036 <&gcc SATA_RXOOB_CLK>,
1037 <&gcc SATA_PMALIVE_CLK>;
1038 clock-names = "slave_face", "iface", "core",
1041 assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
1042 assigned-clock-rates = <100000000>, <100000000>;
1045 phy-names = "sata-phy";
1046 status = "disabled";
1050 compatible = "qcom,ssbi";
1051 reg = <0x00500000 0x1000>;
1052 qcom,controller-type = "pmic-arbiter";
1055 gcc: clock-controller@900000 {
1056 compatible = "qcom,gcc-ipq8064";
1057 reg = <0x00900000 0x4000>;
1060 #power-domain-cells = <1>;
1063 tsens: thermal-sensor@900000 {
1064 compatible = "qcom,ipq8064-tsens";
1065 reg = <0x900000 0x3680>;
1066 nvmem-cells = <&tsens_calib>, <&tsens_backup>;
1067 nvmem-cell-names = "calib", "calib_backup";
1068 interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
1069 #thermal-sensor-cells = <1>;
1072 tcsr: syscon@1a400000 {
1073 compatible = "qcom,tcsr-ipq8064", "syscon";
1074 reg = <0x1a400000 0x100>;
1077 lcc: clock-controller@28000000 {
1078 compatible = "qcom,lcc-ipq8064";
1079 reg = <0x28000000 0x1000>;
1084 sfpb_mutex_block: syscon@1200600 {
1085 compatible = "syscon";
1086 reg = <0x01200600 0x100>;
1089 hs_phy_0: hs_phy_0 {
1090 compatible = "qcom,dwc3-hs-usb-phy";
1092 clocks = <&gcc USB30_0_UTMI_CLK>;
1093 clock-names = "ref";
1097 ss_phy_0: ss_phy_0 {
1098 compatible = "qcom,dwc3-ss-usb-phy";
1100 clocks = <&gcc USB30_0_MASTER_CLK>;
1101 clock-names = "ref";
1105 usb3_0: usb3@110f8800 {
1106 compatible = "qcom,dwc3", "syscon";
1107 #address-cells = <1>;
1109 reg = <0x110f8800 0x8000>;
1110 clocks = <&gcc USB30_0_MASTER_CLK>;
1111 clock-names = "core";
1115 resets = <&gcc USB30_0_MASTER_RESET>;
1116 reset-names = "master";
1118 status = "disabled";
1120 dwc3_0: dwc3@11000000 {
1121 compatible = "snps,dwc3";
1122 reg = <0x11000000 0xcd00>;
1123 interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
1124 phys = <&hs_phy_0>, <&ss_phy_0>;
1125 phy-names = "usb2-phy", "usb3-phy";
1127 snps,dis_u3_susphy_quirk;
1131 hs_phy_1: hs_phy_1 {
1132 compatible = "qcom,dwc3-hs-usb-phy";
1134 clocks = <&gcc USB30_1_UTMI_CLK>;
1135 clock-names = "ref";
1139 ss_phy_1: ss_phy_1 {
1140 compatible = "qcom,dwc3-ss-usb-phy";
1142 clocks = <&gcc USB30_1_MASTER_CLK>;
1143 clock-names = "ref";
1147 usb3_1: usb3@100f8800 {
1148 compatible = "qcom,dwc3", "syscon";
1149 #address-cells = <1>;
1151 reg = <0x100f8800 0x8000>;
1152 clocks = <&gcc USB30_1_MASTER_CLK>;
1153 clock-names = "core";
1157 resets = <&gcc USB30_1_MASTER_RESET>;
1158 reset-names = "master";
1160 status = "disabled";
1162 dwc3_1: dwc3@10000000 {
1163 compatible = "snps,dwc3";
1164 reg = <0x10000000 0xcd00>;
1165 interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
1166 phys = <&hs_phy_1>, <&ss_phy_1>;
1167 phy-names = "usb2-phy", "usb3-phy";
1169 snps,dis_u3_susphy_quirk;
1173 pcie0: pci@1b500000 {
1174 compatible = "qcom,pcie-ipq8064";
1175 reg = <0x1b500000 0x1000
1178 0x0ff00000 0x100000>;
1179 reg-names = "dbi", "elbi", "parf", "config";
1180 device_type = "pci";
1181 linux,pci-domain = <0>;
1182 bus-range = <0x00 0xff>;
1184 #address-cells = <3>;
1187 ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000 /* downstream I/O */
1188 0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */
1190 interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
1191 interrupt-names = "msi";
1192 #interrupt-cells = <1>;
1193 interrupt-map-mask = <0 0 0 0x7>;
1194 interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
1195 <0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
1196 <0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
1197 <0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
1199 clocks = <&gcc PCIE_A_CLK>,
1201 <&gcc PCIE_PHY_CLK>,
1202 <&gcc PCIE_AUX_CLK>,
1203 <&gcc PCIE_ALT_REF_CLK>;
1204 clock-names = "core", "iface", "phy", "aux", "ref";
1206 assigned-clocks = <&gcc PCIE_ALT_REF_CLK>;
1207 assigned-clock-rates = <100000000>;
1209 resets = <&gcc PCIE_ACLK_RESET>,
1210 <&gcc PCIE_HCLK_RESET>,
1211 <&gcc PCIE_POR_RESET>,
1212 <&gcc PCIE_PCI_RESET>,
1213 <&gcc PCIE_PHY_RESET>,
1214 <&gcc PCIE_EXT_RESET>;
1215 reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
1217 pinctrl-0 = <&pcie0_pins>;
1218 pinctrl-names = "default";
1220 perst-gpios = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
1222 phy-tx0-term-offset = <7>;
1224 status = "disabled";
1227 pcie1: pci@1b700000 {
1228 compatible = "qcom,pcie-ipq8064";
1229 reg = <0x1b700000 0x1000
1232 0x31f00000 0x100000>;
1233 reg-names = "dbi", "elbi", "parf", "config";
1234 device_type = "pci";
1235 linux,pci-domain = <1>;
1236 bus-range = <0x00 0xff>;
1238 #address-cells = <3>;
1241 ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000 /* downstream I/O */
1242 0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */
1244 interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
1245 interrupt-names = "msi";
1246 #interrupt-cells = <1>;
1247 interrupt-map-mask = <0 0 0 0x7>;
1248 interrupt-map = <0 0 0 1 &intc 0 58 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
1249 <0 0 0 2 &intc 0 59 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
1250 <0 0 0 3 &intc 0 60 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
1251 <0 0 0 4 &intc 0 61 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
1253 clocks = <&gcc PCIE_1_A_CLK>,
1254 <&gcc PCIE_1_H_CLK>,
1255 <&gcc PCIE_1_PHY_CLK>,
1256 <&gcc PCIE_1_AUX_CLK>,
1257 <&gcc PCIE_1_ALT_REF_CLK>;
1258 clock-names = "core", "iface", "phy", "aux", "ref";
1260 assigned-clocks = <&gcc PCIE_1_ALT_REF_CLK>;
1261 assigned-clock-rates = <100000000>;
1263 resets = <&gcc PCIE_1_ACLK_RESET>,
1264 <&gcc PCIE_1_HCLK_RESET>,
1265 <&gcc PCIE_1_POR_RESET>,
1266 <&gcc PCIE_1_PCI_RESET>,
1267 <&gcc PCIE_1_PHY_RESET>,
1268 <&gcc PCIE_1_EXT_RESET>;
1269 reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
1271 pinctrl-0 = <&pcie1_pins>;
1272 pinctrl-names = "default";
1274 perst-gpios = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
1276 phy-tx0-term-offset = <7>;
1278 status = "disabled";
1281 pcie2: pci@1b900000 {
1282 compatible = "qcom,pcie-ipq8064";
1283 reg = <0x1b900000 0x1000
1286 0x35f00000 0x100000>;
1287 reg-names = "dbi", "elbi", "parf", "config";
1288 device_type = "pci";
1289 linux,pci-domain = <2>;
1290 bus-range = <0x00 0xff>;
1292 #address-cells = <3>;
1295 ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000 /* downstream I/O */
1296 0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */
1298 interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
1299 interrupt-names = "msi";
1300 #interrupt-cells = <1>;
1301 interrupt-map-mask = <0 0 0 0x7>;
1302 interrupt-map = <0 0 0 1 &intc 0 72 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
1303 <0 0 0 2 &intc 0 73 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
1304 <0 0 0 3 &intc 0 74 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
1305 <0 0 0 4 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
1307 clocks = <&gcc PCIE_2_A_CLK>,
1308 <&gcc PCIE_2_H_CLK>,
1309 <&gcc PCIE_2_PHY_CLK>,
1310 <&gcc PCIE_2_AUX_CLK>,
1311 <&gcc PCIE_2_ALT_REF_CLK>;
1312 clock-names = "core", "iface", "phy", "aux", "ref";
1314 assigned-clocks = <&gcc PCIE_2_ALT_REF_CLK>;
1315 assigned-clock-rates = <100000000>;
1317 resets = <&gcc PCIE_2_ACLK_RESET>,
1318 <&gcc PCIE_2_HCLK_RESET>,
1319 <&gcc PCIE_2_POR_RESET>,
1320 <&gcc PCIE_2_PCI_RESET>,
1321 <&gcc PCIE_2_PHY_RESET>,
1322 <&gcc PCIE_2_EXT_RESET>;
1323 reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
1325 pinctrl-0 = <&pcie2_pins>;
1326 pinctrl-names = "default";
1328 perst-gpios = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
1330 phy-tx0-term-offset = <7>;
1332 status = "disabled";
1335 adm_dma: dma@18300000 {
1336 compatible = "qcom,adm";
1337 reg = <0x18300000 0x100000>;
1338 interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
1341 clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
1342 clock-names = "core", "iface";
1344 resets = <&gcc ADM0_RESET>,
1345 <&gcc ADM0_PBUS_RESET>,
1346 <&gcc ADM0_C0_RESET>,
1347 <&gcc ADM0_C1_RESET>,
1348 <&gcc ADM0_C2_RESET>;
1349 reset-names = "clk", "pbus", "c0", "c1", "c2";
1352 status = "disabled";
1355 nand_controller: nand-controller@1ac00000 {
1356 compatible = "qcom,ipq806x-nand";
1357 reg = <0x1ac00000 0x800>;
1359 clocks = <&gcc EBI2_CLK>,
1360 <&gcc EBI2_AON_CLK>;
1361 clock-names = "core", "aon";
1363 dmas = <&adm_dma 3>;
1365 qcom,cmd-crci = <15>;
1366 qcom,data-crci = <3>;
1368 status = "disabled";
1370 #address-cells = <1>;
1374 nss_common: syscon@03000000 {
1375 compatible = "syscon";
1376 reg = <0x03000000 0x0000FFFF>;
1379 qsgmii_csr: syscon@1bb00000 {
1380 compatible = "syscon";
1381 reg = <0x1bb00000 0x000001FF>;
1384 stmmac_axi_setup: stmmac-axi-config {
1385 snps,wr_osr_lmt = <7>;
1386 snps,rd_osr_lmt = <7>;
1387 snps,blen = <16 0 0 0 0 0 0>;
1390 mdio0: mdio@37000000 {
1391 #address-cells = <1>;
1394 compatible = "qcom,ipq8064-mdio", "syscon";
1395 reg = <0x37000000 0x200000>;
1396 resets = <&gcc GMAC_CORE1_RESET>;
1397 reset-names = "stmmaceth";
1398 clocks = <&gcc GMAC_CORE1_CLK>;
1399 clock-names = "stmmaceth";
1401 status = "disabled";
1404 gmac0: ethernet@37000000 {
1405 device_type = "network";
1406 compatible = "qcom,ipq806x-gmac";
1407 reg = <0x37000000 0x200000>;
1408 interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
1409 interrupt-names = "macirq";
1411 snps,axi-config = <&stmmac_axi_setup>;
1415 qcom,nss-common = <&nss_common>;
1416 qcom,qsgmii-csr = <&qsgmii_csr>;
1418 clocks = <&gcc GMAC_CORE1_CLK>;
1419 clock-names = "stmmaceth";
1421 resets = <&gcc GMAC_CORE1_RESET>;
1422 reset-names = "stmmaceth";
1424 status = "disabled";
1427 gmac1: ethernet@37200000 {
1428 device_type = "network";
1429 compatible = "qcom,ipq806x-gmac";
1430 reg = <0x37200000 0x200000>;
1431 interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
1432 interrupt-names = "macirq";
1434 snps,axi-config = <&stmmac_axi_setup>;
1438 qcom,nss-common = <&nss_common>;
1439 qcom,qsgmii-csr = <&qsgmii_csr>;
1441 clocks = <&gcc GMAC_CORE2_CLK>;
1442 clock-names = "stmmaceth";
1444 resets = <&gcc GMAC_CORE2_RESET>;
1445 reset-names = "stmmaceth";
1447 status = "disabled";
1450 gmac2: ethernet@37400000 {
1451 device_type = "network";
1452 compatible = "qcom,ipq806x-gmac", "snps,dwmac";
1453 reg = <0x37400000 0x200000>;
1454 interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
1455 interrupt-names = "macirq";
1457 snps,axi-config = <&stmmac_axi_setup>;
1461 qcom,nss-common = <&nss_common>;
1462 qcom,qsgmii-csr = <&qsgmii_csr>;
1464 clocks = <&gcc GMAC_CORE3_CLK>;
1465 clock-names = "stmmaceth";
1467 resets = <&gcc GMAC_CORE3_RESET>;
1468 reset-names = "stmmaceth";
1470 status = "disabled";
1473 gmac3: ethernet@37600000 {
1474 device_type = "network";
1475 compatible = "qcom,ipq806x-gmac", "snps,dwmac";
1476 reg = <0x37600000 0x200000>;
1477 interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
1478 interrupt-names = "macirq";
1480 snps,axi-config = <&stmmac_axi_setup>;
1484 qcom,nss-common = <&nss_common>;
1485 qcom,qsgmii-csr = <&qsgmii_csr>;
1487 clocks = <&gcc GMAC_CORE4_CLK>;
1488 clock-names = "stmmaceth";
1490 resets = <&gcc GMAC_CORE4_RESET>;
1491 reset-names = "stmmaceth";
1493 status = "disabled";
1496 /* Temporary fixed regulator */
1497 vsdcc_fixed: vsdcc-regulator {
1498 compatible = "regulator-fixed";
1499 regulator-name = "SDCC Power";
1500 regulator-min-microvolt = <3300000>;
1501 regulator-max-microvolt = <3300000>;
1502 regulator-always-on;
1505 sdcc1bam: dma@12402000 {
1506 compatible = "qcom,bam-v1.3.0";
1507 reg = <0x12402000 0x8000>;
1508 interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
1509 clocks = <&gcc SDC1_H_CLK>;
1510 clock-names = "bam_clk";
1515 sdcc3bam: dma@12182000 {
1516 compatible = "qcom,bam-v1.3.0";
1517 reg = <0x12182000 0x8000>;
1518 interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
1519 clocks = <&gcc SDC3_H_CLK>;
1520 clock-names = "bam_clk";
1526 compatible = "arm,amba-bus";
1527 #address-cells = <1>;
1530 sdcc1: sdcc@12400000 {
1531 status = "disabled";
1532 compatible = "arm,pl18x", "arm,primecell";
1533 arm,primecell-periphid = <0x00051180>;
1534 reg = <0x12400000 0x2000>;
1535 interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
1536 interrupt-names = "cmd_irq";
1537 clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
1538 clock-names = "mclk", "apb_pclk";
1540 max-frequency = <96000000>;
1544 vmmc-supply = <&vsdcc_fixed>;
1545 dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
1546 dma-names = "tx", "rx";
1549 sdcc3: sdcc@12180000 {
1550 compatible = "arm,pl18x", "arm,primecell";
1551 arm,primecell-periphid = <0x00051180>;
1552 status = "disabled";
1553 reg = <0x12180000 0x2000>;
1554 interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
1555 interrupt-names = "cmd_irq";
1556 clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
1557 clock-names = "mclk", "apb_pclk";
1561 max-frequency = <192000000>;
1565 vqmmc-supply = <&vsdcc_fixed>;
1566 dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
1567 dma-names = "tx", "rx";
1572 sfpb_mutex: sfpb-mutex {
1573 compatible = "qcom,sfpb-mutex";
1574 syscon = <&sfpb_mutex_block 4 4>;
1576 #hwlock-cells = <1>;
1580 compatible = "qcom,smem";
1581 memory-region = <&smem>;
1582 hwlocks = <&sfpb_mutex 3>;