6 model = "BTHOMEHUBV3A - BT Home Hub 3A"; /* SoC: Lantiq ar9 @ 333MHz */
9 bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
13 failsafe = &power_red;
14 running = &power_blue;
16 internet = &broadband_blue;
17 wifi = &wireless_blue;
21 memory@0 { /* RAM: Samsung K4H511638F-LC 64MB */
22 reg = <0x0 0x4000000>;
38 ranges = <0 0 0x0 0x3ffffff /* addrsel0 */
39 1 0 0x4000000 0x4000010>; /* addsel1 */
40 compatible = "lantiq,localbus", "simple-bus";
42 nand-parts@0 { /* NAND Flash: Samsung K9F5608U0D-JIB0 32MB */
43 compatible = "gen_nand", "lantiq,nand-xway";
46 reg = <1 0x0 0x2000000 >;
49 req-mask = <0x1>; /* PCI request lines to mask during NAND access */
53 reg = <0x00000 0x8000>;
58 reg = <0x8000 0x05c000>;
62 label = "uboot-config";
63 reg = <0x64000 0x004000>;
65 ath9k_cal: partition@68000 {
67 reg = <0x68000 0x004000>;
71 reg = <0x6c000 0x200000>;
75 reg = <0x26c000 0x1d94000>;
80 compatible = "ath9k,eeprom";
81 ath,eep-flash = <&ath9k_cal 0x0000>;
82 ath,mac-offset = <0x10c>;
88 gpio: pinmux@E100B10 {
89 compatible = "lantiq,pinctrl-xr9";
90 pinctrl-names = "default";
91 pinctrl-0 = <&state_default>;
95 reg = <0xE100B10 0xA0>;
97 state_default: pinmux {
99 lantiq,groups = "nand cle", "nand ale";
100 lantiq,function = "ebu";
102 lantiq,open-drain = <0>;
106 lantiq,groups = "nand cs1";
107 lantiq,function = "ebu";
108 lantiq,open-drain = <0>;
113 lantiq,groups = "req1";
114 lantiq,function = "pci";
116 lantiq,open-drain = <1>;
120 lantiq,groups = "gnt1";
121 lantiq,function = "pci";
123 lantiq,open-drain = <0>;
128 lantiq,pins = "io21";
130 lantiq,open-drain = <0>;
141 gpios = <&gpio 33 0>;
146 gpio-reset = <&gpio 21 0>;
152 compatible = "gpio-keys-polled";
153 #address-cells = <1>;
155 poll-interval = <100>;
158 gpios = <&gpio 54 1>;
159 linux,code = <0x198>;
163 gpios = <&gpio 52 1>;
164 linux,code = <0x198>;
168 gpios = <&gpio 53 1>;
169 linux,code = <0x211>;
174 compatible = "gpio-leds";
177 label = "bthomehubv3a:red:wireless";
181 label = "bthomehubv3a:orange:wireless";
184 wireless_blue: wireless-blue {
185 label = "bthomehubv3a:blue:wireless";
190 label = "bthomehubv3a:red:broadband";
191 gpios = <&gpio 11 1>;
194 label = "bthomehubv3a:orange:broadband";
197 broadband_blue: broadband-blue {
198 label = "bthomehubv3a:blue:broadband";
199 gpios = <&gpio 12 1>;
202 power_red: power-red {
203 label = "bthomehubv3a:red:power";
204 gpios = <&gpio 14 1>;
206 power_orange: power-orange {
207 label = "bthomehubv3a:orange:power";
209 default-state = "keep";
211 power_blue: power-blue {
212 label = "bthomehubv3a:blue:power";