5 bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
8 /* the power led can't be controlled, use the wps led instead */
20 reg = <0x0 0x4000000>;
24 gpio: pinmux@E100B10 {
25 pinctrl-names = "default";
26 pinctrl-0 = <&state_default>;
28 state_default: pinmux {
30 lantiq,groups = "mdio";
31 lantiq,function = "mdio";
34 lantiq,groups = "gphy0 led1", "gphy1 led1";
35 lantiq,function = "gphy";
37 lantiq,open-drain = <0>;
43 lantiq,open-drain = <0>;
52 pins_spi_default: pins_spi_default {
54 lantiq,groups = "spi_di";
55 lantiq,function = "spi";
58 lantiq,groups = "spi_do", "spi_clk",
60 lantiq,function = "spi";
69 compatible = "lantiq,xrx200-net";
70 reg = < 0xE108000 0x3000 /* switch */
71 0xE10B100 0x70 /* mdio */
72 0xE10B1D8 0x30 /* mii */
73 0xE10B308 0x30 /* pmac */
75 interrupt-parent = <&icu0>;
79 compatible = "lantiq,xrx200-pdi";
83 mtd-mac-address = <&ath9k_cal 0xf100>;
87 compatible = "lantiq,xrx200-pdi-port";
91 // gpios = <&gpio 42 1>;
94 compatible = "lantiq,xrx200-pdi-port";
100 compatible = "lantiq,xrx200-pdi-port";
103 phy-handle = <&phy11>;
106 compatible = "lantiq,xrx200-pdi-port";
109 phy-handle = <&phy13>;
114 #address-cells = <1>;
116 compatible = "lantiq,xrx200-mdio";
117 phy0: ethernet-phy@0 {
119 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
121 phy5: ethernet-phy@5 {
123 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
125 phy11: ethernet-phy@11 {
127 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
129 phy13: ethernet-phy@13 {
131 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
138 gpios = <&gpio 33 0>;
139 lantiq,portmask = <0x3>;
144 gpios = <&gpio 33 0>;
149 compatible = "lantiq,phy-xrx200";
150 firmware = "lantiq/vr9_phy11g_a2x.bin";
155 compatible = "lantiq,pcie-xway";
159 compatible = "ath9k,eeprom";
160 ath,eep-flash = <&ath9k_cal 0x21000>;
161 ath,mac-offset = <0xf100>;
169 compatible = "gpio-keys-polled";
170 #address-cells = <1>;
172 poll-interval = <100>;
176 linux,code = <0x198>;
183 linux,input-type = <5>; /* EV_SW */
188 gpios = <&gpio 39 1>;
189 linux,code = <0x211>;
194 compatible = "gpio-leds";
196 power is not controllable via gpio
199 label = "tdw89x0:green:dsl";
203 label = "tdw89x0:green:internet";
207 label = "tdw89x0:green:usb";
208 gpios = <&gpio 19 0>;
211 label = "tdw89x0:green:usb2";
212 gpios = <&gpio 20 0>;
215 label = "tdw89x0:green:wps";
216 gpios = <&gpio 37 0>;
222 pinctrl-names = "default";
223 pinctrl-0 = <&pins_spi_default>;
228 #address-cells = <1>;
230 compatible = "jedec,spi-nor";
232 spi-max-frequency = <33250000>;
242 reg = <0x20000 0x7a0000>;
247 reg = <0x7c0000 0x10000>;
252 ath9k_cal: partition@7d0000 {
253 reg = <0x7d0000 0x30000>;
254 label = "boardconfig";