target/linux/ramips/dts/DAP-1522-A1.dts

   1 /dts-v1/;
   2
   3 #include "rt2880.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         compatible = "dlink,dap-1522-a1", "ralink,rt2880-soc";
  10         model = "D-Link DAP-1522 A1";
  11
  12         aliases {
  13                 led-boot = &led_status;
  14                 led-failsafe = &led_status;
  15                 led-running = &led_status;
  16                 led-upgrade = &led_status;
  17         };
  18
  19         cfi@bc400000 {
  20                 compatible = "cfi-flash";
  21                 reg = <0xbc400000 0x800000>;
  22                 bank-width = <2>;
  23                 device-width = <2>;
  24
  25                 partitions {
  26                         compatible = "fixed-partitions";
  27                         #address-cells = <1>;
  28                         #size-cells = <1>;
  29
  30                         partition@0 {
  31                                 label = "uboot";
  32                                 reg = <0x0 0x30000>;
  33                                 read-only;
  34                         };
  35
  36                         factory: partition@30000 {
  37                                 label = "factory";
  38                                 reg = <0x30000 0x10000>;
  39                                 read-only;
  40                         };
  41
  42                         partition@40000 {
  43                                 label = "firmware";
  44                                 reg = <0x40000 0x3a0000>;
  45                         };
  46                 };
  47         };
  48
  49         rtl8366s {
  50                 compatible = "realtek,rtl8366s";
  51                 gpio-sda = <&gpio0 1 GPIO_ACTIVE_HIGH>;
  52                 gpio-sck = <&gpio0 2 GPIO_ACTIVE_HIGH>;
  53         };
  54
  55         gpio-keys-polled {
  56                 compatible = "gpio-keys-polled";
  57                 poll-interval = <100>;
  58
  59                 reset {
  60                         label = "reset";
  61                         gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
  62                         linux,code = <KEY_RESTART>;
  63                 };
  64
  65                 wps {
  66                         label = "wps";
  67                         gpios = <&gpio2 16 GPIO_ACTIVE_LOW>;
  68                         linux,code = <KEY_WPS_BUTTON>;
  69                 };
  70
  71                 ap {
  72                         label = "ap";
  73                         gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
  74                         linux,code = <BTN_0>;
  75                         linux,input-type = <EV_SW>;
  76                 };
  77
  78                 bridge {
  79                         label = "bridge";
  80                         gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
  81                         linux,code = <BTN_1>;
  82                         linux,input-type = <EV_SW>;
  83                 };
  84         };
  85
  86         gpio-leds {
  87                 compatible = "gpio-leds";
  88
  89                 wps {
  90                         label = "dap-1522-a1:blue:wps";
  91                         gpios = <&gpio2 17 GPIO_ACTIVE_LOW>;
  92                 };
  93
  94                 ap {
  95                         label = "dap-1522-a1:blue:ap";
  96                         gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;
  97                 };
  98
  99                 sta {
 100                         label = "dap-1522-a1:red:sta";
 101                         gpios = <&gpio2 19 GPIO_ACTIVE_LOW>;
 102                 };
 103
 104                 led_status: status {
 105                         label = "dap-1522-a1:blue:status";
 106                         gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
 107                 };
 108         };
 109 };
 110
 111 &gpio0 {
 112         status = "okay";
 113 };
 114
 115 &gpio2 {
 116         status = "okay";
 117 };
 118
 119 &pinctrl {
 120         state_default: pinctrl0 {
 121                 gpio {
 122                         ralink,group = "i2c", "uartlite", "pci";
 123                         ralink,function = "gpio";
 124                 };
 125         };
 126 };
 127
 128 &ethernet {
 129         status = "okay";
 130         mtd-mac-address = <&factory 0x2004>;
 131
 132         port@0 {
 133                 mediatek,fixed-link = <1000 1 1 1>;
 134         };
 135
 136         mdio-bus {
 137                 status = "okay";
 138
 139                 phy0: ethernet-phy@0 {
 140                         phy-mode = "mii";
 141                         reg = <0>;
 142                 };
 143         };
 144 };
 145
 146 &wmac {
 147         ralink,mtd-eeprom = <&factory 0x2000>;
 148 };