ath79: convert Araknis AN-300-AP-I-N WiFis to nvmem-cells

[openwrt/openwrt.git] / target / linux / ath79 / dts / ar9331_hak5_lan-turtle.dts

diff --git a/target/linux/ath79/dts/ar9331_hak5_lan-turtle.dts b/target/linux/ath79/dts/ar9331_hak5_lan-turtle.dts
index e6f083482f28d8489b087c768176050949ae7d8b..6a756ed30b0a88c8e29437bedef760b3c6a4d12a 100644 (file)
--- a/target/linux/ath79/dts/ar9331_hak5_lan-turtle.dts
+++ b/target/linux/ath79/dts/ar9331_hak5_lan-turtle.dts
@@ -1,9 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 
-#include "ar9331.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "ar9331_hak5_lan-turtle.dtsi"
 
 / {
        model = "Hak5 LAN Turtle";
@@ -13,21 +10,6 @@
                led-boot = &led_system;
                led-failsafe = &led_system;
                led-upgrade = &led_system;
-               serial0 = &uart;
-       };
-
-       keys {
-               compatible = "gpio-keys";
-
-               pinctrl-names = "default";
-               pinctrl-0 = <&enable_gpio11>;
-
-               reset {
-                       label = "reset";
-                       linux,code = <KEY_RESTART>;
-                       gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
-                       debounce-interval = <60>;
-               };
        };
 
        leds {
@@ -37,84 +19,8 @@
                pinctrl-0 = <&switch_led_disable_pins>;
 
                led_system: system {
-                       label = "lan-turtle:orange:system";
+                       label = "orange:system";
                        gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
                };
        };
 };
-
-&eth0 {
-       status = "okay";
-
-       mtd-mac-address = <&uboot 0x1fc00>;
-       mtd-mac-address-increment = <(-1)>;
-
-       gmac-config {
-               device = <&gmac>;
-
-               switch-phy-addr-swap = <1>;
-               switch-phy-swap = <1>;
-       };
-};
-
-&eth1 {
-       status = "okay";
-
-       mtd-mac-address = <&uboot 0x1fc00>;
-       mtd-mac-address-increment = <1>;
-};
-
-&pinmux {
-       enable_gpio11: pinmux_enable_gpio11 {
-               pinctrl-single,bits = <0x0 0x0 0x4>;
-       };
-};
-
-&spi {
-       status = "okay";
-
-       num-cs = <1>;
-
-       flash@0 {
-               compatible = "jedec,spi-nor";
-               reg = <0>;
-               spi-max-frequency = <50000000>;
-               m25p,fast-read;
-
-               partitions {
-                       compatible = "fixed-partitions";
-                       #address-cells = <1>;
-                       #size-cells = <1>;
-
-                       uboot: partition@0 {
-                               label = "u-boot";
-                               reg = <0x000000 0x020000>;
-                               read-only;
-                       };
-
-                       partition@20000 {
-                               label = "firmware";
-                               reg = <0x020000 0xfd0000>;
-                               compatible = "tplink,firmware";
-                       };
-
-                       partition@ff0000 {
-                               label = "art";
-                               reg = <0xff0000 0x010000>;
-                               read-only;
-                       };
-               };
-       };
-};
-
-&uart {
-       status = "okay";
-};
-
-&usb {
-       status = "okay";
-};
-
-&usb_phy {
-       status = "okay";
-};