openwrt/staging/florian.git
7 years agoar71xx: add support for TP-Link Archer C25 v1
Ludwig Thomeczek [Sat, 22 Apr 2017 16:21:47 +0000 (18:21 +0200)]
ar71xx: add support for TP-Link Archer C25 v1

The TP-Link Archer C25 is a low-cost dual-band router.

Specification:

- CPU: Atheros QCA9561 775 MHz
- RAM: 64 MB
- Flash: 8 MB
- Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887
- NET: 5x 10/100 Mbps Ethernet

Some LEDs are controlled by an additional 74HC595 chip.

Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
[minor code style fixes, boards alphabetical order fixes,
reworked commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: add support for TP-Link TL-WR942N v1
Serg Studzinskii [Wed, 8 Mar 2017 20:10:05 +0000 (22:10 +0200)]
ar71xx: add support for TP-Link TL-WR942N v1

TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on
Qualcomm/Atheros QCA9561.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x USB 2.0
- 11x LED (most are controlled by 74HC595)
- 2x button
- UART header on PCB*

* Serial console is disabled in OEM non-beta firmwares and corresponding
  GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by
  production (non-beta) U-Boot and firmware.

Currently not working:

1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs
   by some U-Boot versions.

Flash instruction under vendor GUI:

1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin".
2. Go to WEB interface and perform usual firmware upgrade.

FLash instruction under U-Boot recovery mode (doesn't work in beta
firmware):

1. Setup PC with static IP "192.168.0.66/24" and tftp server.
2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make
   it available to download from your tftp server.
3. Press "reset" button and power up the router, wait till "WPS" LED
   turns on.

Flash instruction under U-Boot, using UART (can be done only with
preinstalled UART-enabled U-Boot version!):

1. Use "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
   tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin
   erase 0x9f020000 +$filesize
   cp.b 0x81000000 0x9f020000 $filesize
   reset

Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
[minor code style fixes, extended commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: move WRTnode2Q to generic build target
Piotr Dymacz [Fri, 9 Jun 2017 17:56:09 +0000 (19:56 +0200)]
ar71xx: move WRTnode2Q to generic build target

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: image: simplify Ubiquiti devices definitions
Piotr Dymacz [Sat, 10 Jun 2017 16:57:56 +0000 (18:57 +0200)]
ar71xx: image: simplify Ubiquiti devices definitions

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: image: mikrotik: shorten DEVICE_TITLE
Piotr Dymacz [Sat, 10 Jun 2017 11:48:34 +0000 (13:48 +0200)]
ar71xx: image: mikrotik: shorten DEVICE_TITLE

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: image: use simply expanded variables
Piotr Dymacz [Thu, 8 Jun 2017 13:18:34 +0000 (15:18 +0200)]
ar71xx: image: use simply expanded variables

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: image: update GL.iNet boards DEVICE_TITLE
Piotr Dymacz [Wed, 31 May 2017 20:12:51 +0000 (22:12 +0200)]
ar71xx: image: update GL.iNet boards DEVICE_TITLE

Use "GL.iNet" as vendor name (based on information from the vendor, this
is registered name of the company) and align model names with official
website.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: image: fix 8devices boards DEVICE_TITLE
Piotr Dymacz [Wed, 31 May 2017 19:56:10 +0000 (21:56 +0200)]
ar71xx: image: fix 8devices boards DEVICE_TITLE

Be consistent with DEVICE_TITLE syntax and use vendor + board names.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: image: drop unused mtdlayouts from legacy.mk
Piotr Dymacz [Wed, 7 Jun 2017 20:37:30 +0000 (22:37 +0200)]
ar71xx: image: drop unused mtdlayouts from legacy.mk

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: image: cosmetic: drop redundant empty lines
Piotr Dymacz [Wed, 31 May 2017 19:23:53 +0000 (21:23 +0200)]
ar71xx: image: cosmetic: drop redundant empty lines

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: image: add ROOTFS_SIZE to DEVICE_VARS
Piotr Dymacz [Wed, 31 May 2017 18:02:36 +0000 (20:02 +0200)]
ar71xx: image: add ROOTFS_SIZE to DEVICE_VARS

Also use ROOTFS_SIZE variable in place of static values.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: image: keep custom Build/* functions in separate files
Piotr Dymacz [Wed, 31 May 2017 14:31:44 +0000 (16:31 +0200)]
ar71xx: image: keep custom Build/* functions in separate files

Most of the custom Build/* functions in ar71xx target are rarely used by
image building code for devices from more than one subtarget. As they
don't need to be always included, move them to corresponding *.mk files.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: image: keep DEVICE_VARS and Build/* at the beginning
Piotr Dymacz [Wed, 31 May 2017 09:16:22 +0000 (11:16 +0200)]
ar71xx: image: keep DEVICE_VARS and Build/* at the beginning

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: image: simplify Compex devices definitions
Piotr Dymacz [Tue, 30 May 2017 21:20:16 +0000 (23:20 +0200)]
ar71xx: image: simplify Compex devices definitions

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: image: drop redundant kmod-usb-ohci from DEVICE_PACKAGES
Piotr Dymacz [Tue, 30 May 2017 20:55:29 +0000 (22:55 +0200)]
ar71xx: image: drop redundant kmod-usb-ohci from DEVICE_PACKAGES

kmod-usb-ohci is needed only on devices with AR71xx and AR7240 SoCs.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: image: drop redundant uboot-envtools from DEVICE_PACKAGES
Piotr Dymacz [Tue, 30 May 2017 20:25:02 +0000 (22:25 +0200)]
ar71xx: image: drop redundant uboot-envtools from DEVICE_PACKAGES

uboot-envtools is already included in DEFAULT_PACKAGES for ar71xx.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agofirmware-utils: tplink-safeloader: support strings as soft_version
Jan Niehusmann [Fri, 19 May 2017 07:42:24 +0000 (09:42 +0200)]
firmware-utils: tplink-safeloader: support strings as soft_version

Some TP-Link routers (C25, C59, C60) contain a version string instead
of a binary structure in the soft_version partition.

Flashing LEDE from the original firmware's GUI, this version string
taken from the soft_ver partition of the firmware image is written to
the router's config partition.

When using tftp recovery to go back to the original Archer C25 firmware,
a version check compares that version to the version of the firmware to
be flashed.

Without proper contents in the config partition, reverting to the
original firmware fails.

Therefore, write the string "soft_ver:1.0.0\n" to that soft_ver
partition.

Signed-off-by: Jan Niehusmann <jan@gondor.com>
7 years agoar71xx: fixup ar71xx/ar933x_wmac_reset: remove indefinite wait for wmac reset
Kevin Darbyshire-Bryant [Sun, 11 Jun 2017 13:36:17 +0000 (14:36 +0100)]
ar71xx: fixup ar71xx/ar933x_wmac_reset: remove indefinite wait for wmac reset

Fix malformed patch introduced by 296312fca13a4cab1d157e0474e1f0bcca6adf5c

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
7 years agodnsmasq: make bind-dynamic 'non-wildcard' interfaces default
Kevin Darbyshire-Bryant [Fri, 24 Feb 2017 10:08:30 +0000 (10:08 +0000)]
dnsmasq: make bind-dynamic 'non-wildcard' interfaces default

'non-wildcard' interfaces enables dnsmasq's '--bind-dynamic' mode.  This
binds to interfaces rather than wildcard addresses *and* keeps track of
interface comings/goings via a unique Linux api.

Quoting dnsmasq's author "bind-dynamic (bind individual addresses, keep
up with changes in interface config) ... On linux, there's actually no
sane reason not to use --bind-dynamic, and it's only not the default for
historical reasons."

Let's change history, well on LEDE at least, and change the default!

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
7 years agoar71xx/ar93xx_wmac_otp_read_word: fix wrongly used sizeof(*u)
Alexander Couzens [Sun, 11 Jun 2017 11:43:55 +0000 (13:43 +0200)]
ar71xx/ar93xx_wmac_otp_read_word: fix wrongly used sizeof(*u)

Found-by: Coverity Scan #1330474
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
7 years agolinux/swconfig_get_attr: fix leak of msg in case of error
Alexander Couzens [Sun, 11 Jun 2017 11:33:18 +0000 (13:33 +0200)]
linux/swconfig_get_attr: fix leak of msg in case of error

Found-by: Coverity Scan #1330102
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
7 years agolinux/ledtrig-netdev: remove `unsigned < 0` check
Alexander Couzens [Sun, 11 Jun 2017 11:30:21 +0000 (13:30 +0200)]
linux/ledtrig-netdev: remove `unsigned < 0` check

Found-by: Coverity Scan
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
7 years agoar71xx/ar933x_wmac_reset: remove indefinite wait for wmac reset
Alexander Couzens [Sun, 11 Jun 2017 11:27:20 +0000 (13:27 +0200)]
ar71xx/ar933x_wmac_reset: remove indefinite wait for wmac reset

Found-by: Coverity Scan #1329327
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
7 years agoar71xx/ag71xx_ethtool: don't return uninitialized return value on success
Alexander Couzens [Sun, 11 Jun 2017 10:51:58 +0000 (12:51 +0200)]
ar71xx/ag71xx_ethtool: don't return uninitialized return value on success

ag71xx_ethtool_set_ringparam() will return an uninitialized value on
success.

Found-by: Coverity Scan #1330877
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
7 years agoar71xx/ag71xx_mdio_probe: fix a memory leak when probe fails
Alexander Couzens [Sun, 11 Jun 2017 10:49:19 +0000 (12:49 +0200)]
ar71xx/ag71xx_mdio_probe: fix a memory leak when probe fails

Found-by: Coverity Scan #1330233
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
7 years agoar71xx/ag71xx_ar7240_get_port_link: fix off-by-one check on argument `port`
Alexander Couzens [Sun, 11 Jun 2017 10:43:24 +0000 (12:43 +0200)]
ar71xx/ag71xx_ar7240_get_port_link: fix off-by-one check on argument `port`

Found-by: Coverity Scan #1329901
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
7 years agobase-files: board.json's switch reset means existence, not argument
Jonas Gorski [Sun, 11 Jun 2017 10:50:14 +0000 (12:50 +0200)]
base-files: board.json's switch reset means existence, not argument

Don't pass the value unconditionally to swconfig as a parameter but
instead only call reset if it is 1.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agobrcm63xx: probe SPI connected switches through DT
Jonas Gorski [Thu, 9 Feb 2017 20:58:36 +0000 (21:58 +0100)]
brcm63xx: probe SPI connected switches through DT

Now that we can configure the switches through DT, do so.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agob53: allow configuration through device tree
Jonas Gorski [Thu, 9 Feb 2017 20:20:41 +0000 (21:20 +0100)]
b53: allow configuration through device tree

Add support for the same binding as upstream b53 to allow an
easy switch.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agobrcm63xx: switch to hardware led controllers
Jonas Gorski [Thu, 11 May 2017 11:50:18 +0000 (13:50 +0200)]
brcm63xx: switch to hardware led controllers

Instead of bit banging SPI to talk to the GPIO chip, use the hardware
led controllers intended for controlling the LEDs.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agobrcm63xx: leds-bcm6328: fix signal assignments for leds 4~7
Jonas Gorski [Sun, 14 May 2017 21:45:31 +0000 (23:45 +0200)]
brcm63xx: leds-bcm6328: fix signal assignments for leds 4~7

Properly use modulus for bit calculation for LEDs 4 to 7.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agobrcm63xx: dsl-275xb-d: configure switch leds
Jonas Gorski [Sun, 14 May 2017 20:21:08 +0000 (22:21 +0200)]
brcm63xx: dsl-275xb-d: configure switch leds

Add pinctrl configuration to configure the switch leds on DSL-275XB.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agobrcm63xx: add pinctrl support
Jonas Gorski [Fri, 1 Jul 2016 09:23:06 +0000 (11:23 +0200)]
brcm63xx: add pinctrl support

Add and enable pincontrol drivers, and update dts(i) files with
appropriate hogs.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agokernel: make regmap LZO cache optional
Jonas Gorski [Thu, 8 Jun 2017 08:40:50 +0000 (10:40 +0200)]
kernel: make regmap LZO cache optional

There are no users, so hide it and let future users select it. Saves
about ~17 kB on MIPS.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agobrcm63xx: backport upstream generic gpio changes
Jonas Gorski [Fri, 1 Jul 2016 09:22:08 +0000 (11:22 +0200)]
brcm63xx: backport upstream generic gpio changes

Backport patches that add a data pointer to gpio_chip.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agokexec-tools: bump version and add support for crashdump kernel
Daniel Golle [Tue, 21 Mar 2017 21:58:13 +0000 (15:58 -0600)]
kexec-tools: bump version and add support for crashdump kernel

split kexec-tools into two packages, kexec and kdump.
* kexec to simply execute a new kernel
* kdump is for loading and collecting debris of a crashed kernel with
  support for kdump forensics.

In order to properly support booting into a crashkernel, an init script
as well as UCI configuration has been added.
As modifying the kernel cmdline is required for this to work in x86
platforms use an uci-defaults script to modify /boot/grub/grub.cfg.

To test collecting crash information, use the 'c' sysrq-trigger, ie.
echo c > /proc/sysrq-trigger

This should result in the crash kernel being executed and (depending
on the configution) dmesg and/or vmcore getting saved.

To check if the crash kernel was loaded properly, use the 'status'
command of the kdump init script.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
7 years agodnsmasq: add dhcp-script hook conditionally
Hans Dedecker [Fri, 9 Jun 2017 14:24:12 +0000 (16:24 +0200)]
dnsmasq: add dhcp-script hook conditionally

Commit b32689afd6a661339861086c669e15c936293cf8 added support for dhcp-script hook.
Adding dhcp-script config option results into two instances of dnsmasq being run
which triggered oom issues on platforms having low memory.

The dnsmasq dhcp-script config option will now only be added if at least one of the
dhcp, tftp, neigh hotplug dirs has a regular hotplug file or if the dhcpscript uci
config option is specified.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
7 years agobcm53xx: include wpad-mini only on devices with (supported) wireless
Rafał Miłecki [Mon, 22 May 2017 10:50:53 +0000 (12:50 +0200)]
bcm53xx: include wpad-mini only on devices with (supported) wireless

Don't include wpad-mini when it's useless just like we don't include
useless wireless drivers.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
7 years agobase-files: network.sh: fix a number of IPv6 logic flaws
Jo-Philipp Wich [Thu, 8 Jun 2017 17:27:46 +0000 (19:27 +0200)]
base-files: network.sh: fix a number of IPv6 logic flaws

* Change network_get_subnet6() to sensibly guess a suitable prefix

  Attempt to return the first non-linklocal, non-ula range, then attempt
  to return the first non-linklocal range and finally fall back to the
  previous behaviour of simply returning the first found item.

* Fix network_get_ipaddrs_all()

  Instead of replicating the flawed logic appending a fixed ":1" suffix
  to IPv6 addresses, rely on network_get_ipaddrs() and network_get_ipaddrs6()
  to build a single list of all interface addresses.

* Fix network_get_subnets6()

  Instead of replicating the flawed logic appending a fixed ":1" suffix
  to IPv6 addresses, rely on the ipv6-prefix-assignment.local-address
  field to figure out the proper network address.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
7 years agomwlwifi: update to version 10.3.4.0 / 2017-06-06
Jo-Philipp Wich [Thu, 8 Jun 2017 17:54:53 +0000 (19:54 +0200)]
mwlwifi: update to version 10.3.4.0 / 2017-06-06

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
7 years agoinclude/toplevel: set env GIT_ASKPASS=/bin/true
Alexander Couzens [Wed, 7 Jun 2017 21:56:19 +0000 (23:56 +0200)]
include/toplevel: set env GIT_ASKPASS=/bin/true

When git-https request a service (e.g. github) which ask for credentials
git will pass this request to the user resulting download.pl to wait for
user input. Set GIT_ASKPASS to stop asking.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
7 years agobase-files: network.sh: properly report local IPv6 addresses
Jo-Philipp Wich [Thu, 8 Jun 2017 10:02:36 +0000 (12:02 +0200)]
base-files: network.sh: properly report local IPv6 addresses

Rework the network_get_ipaddr6() and network_get_ipaddrs6() functions to
fetch the effective local IPv6 address of delegated prefix from the
"local-address" field instead of naively hardcoding ":1" as static suffix.

Fixes FS#829.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
7 years agobuild: ensure that flock is available for make download
Felix Fietkau [Thu, 8 Jun 2017 09:05:05 +0000 (11:05 +0200)]
build: ensure that flock is available for make download

It ensures that make download can parallelize downloads, even when some
packages download the same files (e.g. gcc/initial, gcc/final)

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agokernel: update kernel 4.9 to 4.9.31
Jo-Philipp Wich [Wed, 7 Jun 2017 22:24:27 +0000 (00:24 +0200)]
kernel: update kernel 4.9 to 4.9.31

Fixes the following security vulnerabilities:

CVE-2017-8890
The inet_csk_clone_lock function in net/ipv4/inet_connection_sock.c in the
Linux kernel through 4.10.15 allows attackers to cause a denial of service
(double free) or possibly have unspecified other impact by leveraging use
of the accept system call.

CVE-2017-9074
The IPv6 fragmentation implementation in the Linux kernel through 4.11.1
does not consider that the nexthdr field may be associated with an invalid
option, which allows local users to cause a denial of service (out-of-bounds
read and BUG) or possibly have unspecified other impact via crafted socket
and send system calls.

CVE-2017-9075
The sctp_v6_create_accept_sk function in net/sctp/ipv6.c in the Linux kernel
through 4.11.1 mishandles inheritance, which allows local users to cause a
denial of service or possibly have unspecified other impact via crafted
system calls, a related issue to CVE-2017-8890.

CVE-2017-9076
The dccp_v6_request_recv_sock function in net/dccp/ipv6.c in the Linux
kernel through 4.11.1 mishandles inheritance, which allows local users to
cause a denial of service or possibly have unspecified other impact via
crafted system calls, a related issue to CVE-2017-8890.

CVE-2017-9077
The tcp_v6_syn_recv_sock function in net/ipv6/tcp_ipv6.c in the Linux kernel
through 4.11.1 mishandles inheritance, which allows local users to cause a
denial of service or possibly have unspecified other impact via crafted
system calls, a related issue to CVE-2017-8890.

CVE-2017-9242
The __ip6_append_data function in net/ipv6/ip6_output.c in the Linux kernel
through 4.11.3 is too late in checking whether an overwrite of an skb data
structure may occur, which allows local users to cause a denial of service
(system crash) via crafted system calls.

Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-8890
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9074
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9075
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9076
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9077
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9242
Ref: https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.9.31

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
7 years agokernel: really select kernel 4.4.71
Hauke Mehrtens [Wed, 7 Jun 2017 20:57:41 +0000 (22:57 +0200)]
kernel: really select kernel 4.4.71

The previous commit f4a4f324cb76ad ("kernel: update kernel 4.4 to
4.4.71") missed the line which changes the kernel version, add it now.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
7 years agokernel: update kernel 4.4 to 4.4.71
Jo-Philipp Wich [Wed, 7 Jun 2017 16:15:24 +0000 (18:15 +0200)]
kernel: update kernel 4.4 to 4.4.71

Fixes the following security vulnerabilities:

CVE-2017-8890
The inet_csk_clone_lock function in net/ipv4/inet_connection_sock.c in the
Linux kernel through 4.10.15 allows attackers to cause a denial of service
(double free) or possibly have unspecified other impact by leveraging use
of the accept system call.

CVE-2017-9074
The IPv6 fragmentation implementation in the Linux kernel through 4.11.1
does not consider that the nexthdr field may be associated with an invalid
option, which allows local users to cause a denial of service (out-of-bounds
read and BUG) or possibly have unspecified other impact via crafted socket
and send system calls.

CVE-2017-9075
The sctp_v6_create_accept_sk function in net/sctp/ipv6.c in the Linux kernel
through 4.11.1 mishandles inheritance, which allows local users to cause a
denial of service or possibly have unspecified other impact via crafted
system calls, a related issue to CVE-2017-8890.

CVE-2017-9076
The dccp_v6_request_recv_sock function in net/dccp/ipv6.c in the Linux
kernel through 4.11.1 mishandles inheritance, which allows local users to
cause a denial of service or possibly have unspecified other impact via
crafted system calls, a related issue to CVE-2017-8890.

CVE-2017-9077
The tcp_v6_syn_recv_sock function in net/ipv6/tcp_ipv6.c in the Linux kernel
through 4.11.1 mishandles inheritance, which allows local users to cause a
denial of service or possibly have unspecified other impact via crafted
system calls, a related issue to CVE-2017-8890.

CVE-2017-9242
The __ip6_append_data function in net/ipv6/ip6_output.c in the Linux kernel
through 4.11.3 is too late in checking whether an overwrite of an skb data
structure may occur, which allows local users to cause a denial of service
(system crash) via crafted system calls.

Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-8890
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9074
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9075
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9076
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9077
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9242
Ref: https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.4.71

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
7 years agoautomake: import upstream fix for perl 5.26
Daniel Golle [Wed, 7 Jun 2017 17:39:33 +0000 (19:39 +0200)]
automake: import upstream fix for perl 5.26

Build broke as distributions now include Perl 5.26 and automake
triggered an "Unescaped left brace in regex" error.
Import upstream commit 13f00eb449 to fix that.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
7 years agogdb: disable simulator ; it's broken on ppc
Alexandru Ardelean [Fri, 12 May 2017 08:50:55 +0000 (11:50 +0300)]
gdb: disable simulator ; it's broken on ppc

Error is:
```
ompile-loc2c.o compile-c-support.o inflow.o    init.o \
  ../sim/ppc/libsim.a -lreadline ../opcodes/libopcodes.a ../bfd/libbfd.a -L./../zlib -lz  ../libiberty/libiberty.a ../libdecnumber/libdecnumber.a    -lncurses -lm     ../libiberty/libiberty.a  build-gnulib/import/libgnu.a  -ldl -Wl,--dynamic-list=./proc-service.list
../sim/ppc/libsim.a(idecode.o): In function `update_time_from_event':
idecode.c:(.text+0x170): undefined reference to `error'
../sim/ppc/libsim.a(idecode.o): In function `event_queue_tick':
idecode.c:(.text+0x1cc): undefined reference to `error'
idecode.c:(.text+0x28c): undefined reference to `error'
idecode.c:(.text+0x318): undefined reference to `error'
../sim/ppc/libsim.a(idecode.o): In function `cpu_halt.constprop.6':
idecode.c:(.text+0x398): undefined reference to `error'
../sim/ppc/libsim.a(idecode.o):idecode.c:(.text+0x4e4): more undefined references to `error' follow
collect2: error: ld returned 1 exit status
Makefile:1420: recipe for target 'gdb' failed
make[5]: *** [gdb] Error 1
```

Seems others are running into this as well.
The problem seems to be that some code may be built
as C++ and not C, which may explain the linker error.

On this thread reply:
   https://sourceware.org/ml/gdb/2016-11/msg00045.html
it mentions that the simulator should not call GDB's
"error" function directly, but rather use the "host_callback"
struct.

I have no idea about the use of the GDB simulator within
the OpenWrt/LEDE community.

So, I took the easier route, which is to disable the simulator.
(Also suggested here: https://sourceware.org/ml/gdb/2016-11/msg00047.html )

If needed, I can make an effort to fix the simulator for PPC.

Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
7 years agogdb: remove Build/Compile rule ; default one works
Alexandru Ardelean [Fri, 12 May 2017 08:50:05 +0000 (11:50 +0300)]
gdb: remove Build/Compile rule ; default one works

Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
7 years agokernel: remove CONFIG_ZONE_DMA_FLAG from 4.9
Sergey Ryazanov [Tue, 30 May 2017 21:46:41 +0000 (00:46 +0300)]
kernel: remove CONFIG_ZONE_DMA_FLAG from 4.9

There are no CONFIG_ZONE_DMA_FLAG config symbol since 4.7.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
7 years agokernel: disable CONFIG_SG_POOL by default
Sergey Ryazanov [Tue, 30 May 2017 21:46:40 +0000 (00:46 +0300)]
kernel: disable CONFIG_SG_POOL by default

CONFIG_SG_POOL symbol is selected only by CONFIG_SCSI, since the last
one is disabled by default then disable CONFIG_SG_POOL by default too.
And explicitly enable it only for platforms that use CONFIG_SCSI.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
7 years agoath25: add missed HAVE_IRQ_EXIT_ON_IRQ_STACK
Sergey Ryazanov [Tue, 30 May 2017 21:46:39 +0000 (00:46 +0300)]
ath25: add missed HAVE_IRQ_EXIT_ON_IRQ_STACK

Add HAVE_IRQ_EXIT_ON_IRQ_STACK kernel configuration symbol that was
missed during backporting separate IRQ stack for MIPS from upstream.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
7 years agorb532: enable high-res timers, refresh kernel config
Felix Fietkau [Thu, 1 Jun 2017 09:17:13 +0000 (11:17 +0200)]
rb532: enable high-res timers, refresh kernel config

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agoxburst: enable high-res timers, refresh kernel config
Felix Fietkau [Thu, 1 Jun 2017 09:15:39 +0000 (11:15 +0200)]
xburst: enable high-res timers, refresh kernel config

Helps with system performance

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agoocteon: enable high-res timers
Felix Fietkau [Thu, 1 Jun 2017 09:11:11 +0000 (11:11 +0200)]
octeon: enable high-res timers

Helps with network stack performance

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agokernel: add CONFIG_SCHED_HRTICK=y to the generic config
Felix Fietkau [Thu, 1 Jun 2017 09:10:21 +0000 (11:10 +0200)]
kernel: add CONFIG_SCHED_HRTICK=y to the generic config

It is used by pretty much every target

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agopackage/grub2: update to 2.02
Alif M. Ahmad [Sat, 20 May 2017 07:11:16 +0000 (14:11 +0700)]
package/grub2: update to 2.02

Update to version 2.02

Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
7 years agox86: include USB HID by default
Lucian Cristian [Thu, 25 May 2017 16:15:44 +0000 (19:15 +0300)]
x86: include USB HID by default

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
7 years agokernel: fix segmentation fault in mconf on linux
Felix Fietkau [Wed, 7 Jun 2017 16:14:27 +0000 (18:14 +0200)]
kernel: fix segmentation fault in mconf on linux

Commit 86c966a8ae9c4e74b912a16a760aaed17c68eb32 caused HOST_LOADLIBES to
include -lncurses. This was added for fixing build issues on macOS.
This introduces issues on Linux when wide-character ncurses is being
used for compiling, but the non-wide-character version is linked in.

Fix this by adding the extra override for HOST_LOADLIBES only on macOS.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agomac80211: use KERNEL_MAKEOPTS
Felix Fietkau [Thu, 16 Mar 2017 09:13:14 +0000 (10:13 +0100)]
mac80211: use KERNEL_MAKEOPTS

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agobuild: add KERNEL_MAKE and KERNEL_MAKE_FLAGS variables and move to kernel.mk
Felix Fietkau [Thu, 16 Mar 2017 08:53:30 +0000 (09:53 +0100)]
build: add KERNEL_MAKE and KERNEL_MAKE_FLAGS variables and move to kernel.mk

This allows packages to use kernel make options without the forced
-C $(LINUX_DIR). It also makes it more clear that it to be called from
kernel module packages directly.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
7 years agokernel: update myloader for linux 4.9
Sergey Ryazanov [Tue, 30 May 2017 21:46:42 +0000 (00:46 +0300)]
kernel: update myloader for linux 4.9

add backport patches for older kernels.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
7 years agoip17xx: correct aneg_done return value
Sergey Ryazanov [Tue, 6 Jun 2017 22:25:32 +0000 (01:25 +0300)]
ip17xx: correct aneg_done return value

PHY core treats any positive return value as the auto-negotiation done
indication. Since we do not actually check any device register in this
callback then update it to return positive value with a neutral meaning
instead of the register flag to avoid  confusing for future readers.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
7 years agomvswitch: fix autonegotiation issue
Sergey Ryazanov [Tue, 6 Jun 2017 22:25:31 +0000 (01:25 +0300)]
mvswitch: fix autonegotiation issue

The Marvel 88E6060 switch has an MDIO interface, but does not emulate
regular PHY behavior for the host. The network core can not detect using
the generic code, whether the connection via the attached PHY can be
used or not. The PHY's state machine is stuck in a state of
auto-negotiation and does not go any further so the Ethernet interface
of the router stay forever in the not-runing state.

Fix this issue by implementing the aneg_done callback to be able to
inform the network core that the Ethernet interface link to which the
switch is connected can be marked as RUNNING.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
7 years agolinux/ath25: fixing some tabs and whitespace
Sven Roederer [Tue, 6 Jun 2017 13:52:06 +0000 (15:52 +0200)]
linux/ath25: fixing some tabs and whitespace

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
7 years agoath25: drop 4.4 kernel support
Sergey Ryazanov [Wed, 7 Jun 2017 04:49:46 +0000 (06:49 +0200)]
ath25: drop 4.4 kernel support

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
7 years agoath25: switch to 4.9 kernel
Sergey Ryazanov [Tue, 6 Jun 2017 22:49:39 +0000 (01:49 +0300)]
ath25: switch to 4.9 kernel

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
7 years agoath25: 4.9: fix Ethernet link autonegotiation
Sergey Ryazanov [Tue, 6 Jun 2017 22:49:38 +0000 (01:49 +0300)]
ath25: 4.9: fix Ethernet link autonegotiation

Drop the own PHY polling function and switch to using the kernel PHY
state machine. This change allows driver to work correctly with devices
that do not support PHY behaviour but whose driver could emulate
autonegotiation completion (e.g. MV88E6060 and IP17xx switches).

NB: earlier this driver rely on flaws in PHY core code and could use PHY
device without really starting it. But now (at least in kernel 4.9)
this trick no more work and network interface could stuck in not-running
state.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
7 years agoath25: 4.9: fix Ethernet tiny issues
Sergey Ryazanov [Tue, 6 Jun 2017 22:49:37 +0000 (01:49 +0300)]
ath25: 4.9: fix Ethernet tiny issues

Few tiny fixes for issues caused by changes in the upstream:
 - do not touch PHY IRQ array (core code initializes it itself now)
 - add missed SET_NETDEV_DEV() invocation (causes segfault during phy
   connection)
 - use phy API inside the MDIO probe function instead of direct field
   access (consider phy structure changes in upstream and prevent
   similar issues in the future)

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
7 years agoath25: 4.9: fix GPIO compile issues
Sergey Ryazanov [Tue, 6 Jun 2017 22:49:36 +0000 (01:49 +0300)]
ath25: 4.9: fix GPIO compile issues

Consider renaming the dev field to parent in the upstream.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
7 years agoath25: add preliminary kernel 4.9 support
Sergey Ryazanov [Tue, 6 Jun 2017 22:49:35 +0000 (01:49 +0300)]
ath25: add preliminary kernel 4.9 support

Copy and refresh patches and config from 4.4

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
7 years agoramips: add support for Ubiquiti EdgeRouter X-SFP
Sven Roederer [Mon, 29 May 2017 09:24:49 +0000 (11:24 +0200)]
ramips: add support for Ubiquiti EdgeRouter X-SFP

This patch adds support for the Ubiquiti EdgeRouter X-SFP and
improves support for the EdgeRouter X (PoE-passthrough).

Specification:
- SoC: MediaTek MT7621AT
- Flash: 256 MiB
- RAM: 265 MiB
- Ethernet: 5 x LAN (1000 Mbps)
- UART: 1 x UART on PCB (3.3V, RX, TX, GND) - 57600 8N1
- EdgeRouter X:
  - 1 x PoE-Passtrough (Eth4)
  - powered by Wallwart or passive PoE
- EdgeRouter X-SFP:
  - 5 x PoE-Out (24V, passive)
  - 1 x SFP (unknown status)
  - powered by Wallwart (24V)

Doesn't work:
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
  nand/spi drivers do not support pin sharing,
  so it is not accessable and disabled. Stock
  firmware could read it and it was empty.

Installation

via vendor firmware:
- build an Initrd-image (> 3MiB) and upload the factory-image
- initrd can have luci-mod-failsafe
- flash final firmware via LuCI / sysupgrade on rebooted system

via TFTP:
- stop uboot into tftp-load into option "1"
- upload factory.bin image

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
7 years agoipq806x: Enable ubi image for ipq40xx AP-DK04.1-C1 board
Ram Chandra Jangir [Wed, 31 May 2017 15:20:29 +0000 (20:50 +0530)]
ipq806x: Enable ubi image for ipq40xx AP-DK04.1-C1 board

This change add IPQ40xx AP-DK04.1-C1 board image support,
enables ubi image for IPQ40xx AP-DK04.1-C1 board and also
add sysupgrage support for AP-DK04.1-C1 and generates a
sysupgrade.tar image.

Testing:
 *Tested on IPQ40xx AP-DK04.1-C1:
   a. NAND boot
   b. ubi sysupgrade

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
7 years agoipq806x: Updated various ipq40xx pin definitions
Ram Chandra Jangir [Wed, 31 May 2017 15:20:28 +0000 (20:50 +0530)]
ipq806x: Updated various ipq40xx pin definitions

This change populates default values for various GPIO functions
in ipq40xx pinctrl driver.

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
7 years agoAdd missing APU1 reference to x86 board.d
Kristian Evensen [Mon, 5 Jun 2017 08:24:02 +0000 (10:24 +0200)]
Add missing APU1 reference to x86 board.d

x86 board.d only contains a case for the APU2, not the APU1. This
causes, for example, network configuration not to be created correctly.
Even though the APU1 seems to reaching EOL, there a still a lot of them
out there.

The APU1 and APU2 is configured in the same way and this patch should
also be considered for stable, as the error also exists there.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
7 years agoperf: Depend on KERNEL_PERF_EVENTS
Florian Fainelli [Mon, 22 May 2017 23:50:47 +0000 (16:50 -0700)]
perf: Depend on KERNEL_PERF_EVENTS

The kernel needs to have PERF_EVENTS built otherwise we will run into
the following:

root@(none):/# perf top
perf_event_open(..., PERF_FLAG_FD_CLOEXEC) failed with unexpected error
89 (Function not implemented)
perf_event_open(..., 0) failed unexpectedly with error 89 (Function not
implemented)
Error:
The sys_perf_event_open() syscall returned with 89 (Function not
implemented) for event (cycles).
/bin/dmesg may provide additional information.
No CONFIG_PERF_EVENTS=y kernel support configured?

Make sure this functional dependency is captured.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
7 years agomdadm: Do not check RUN_DIR
Florian Fainelli [Wed, 31 May 2017 21:39:12 +0000 (14:39 -0700)]
mdadm: Do not check RUN_DIR

Fixes build failure on hosts that do not have mdadm
installed/configured:

make[3]: Entering directory
`/local/users/fainelli/openwrt/trunk/build_dir/target-mipsel-linux-gnu_glibc/mdadm-4.0'
***** Parent of /run/mdadm does not exist.  Maybe set different RUN_DIR=
*****  e.g. make RUN_DIR=/dev/.mdadm
***** or set CHECK_RUN_DIR=0
make[3]: *** [check_rundir] Error 1
make[3]: Leaving directory
`/local/users/fainelli/openwrt/trunk/build_dir/target-mipsel-linux-gnu_glibc/mdadm-4.0'
make[2]: ***
[/local/users/fainelli/openwrt/trunk/build_dir/target-mipsel-linux-gnu_glibc/mdadm-4.0/.built]
Error 2
make[2]: Leaving directory
`/local/users/fainelli/openwrt/trunk/package/utils/mdadm'
make[1]: *** [package/utils/mdadm/compile] Error 2
make[1]: Leaving directory `/local/users/fainelli/openwrt/trunk'
make: *** [package/mdadm/compile] Error 2

Fixes: 980c41f8e04f ("utils/mdadm: Update to 4.0")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
7 years agobrcm63xx: drop support for specifying SPI flash part parsers
Jonas Gorski [Tue, 7 Feb 2017 13:28:07 +0000 (14:28 +0100)]
brcm63xx: drop support for specifying SPI flash part parsers

No need to keep this since we set them from device-tree.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agobrcm63xx: drop support for caldata in brcm63xxpart
Jonas Gorski [Tue, 7 Feb 2017 13:26:15 +0000 (14:26 +0100)]
brcm63xx: drop support for caldata in brcm63xxpart

Now that we always provide these partitions through DT, we don't need to
pass their data through parser data from board files anymore.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agobrcm63xx: probe SPI flash through DT
Jonas Gorski [Tue, 7 Feb 2017 13:24:31 +0000 (14:24 +0100)]
brcm63xx: probe SPI flash through DT

Now that we support problem the SPI controllers through DT, we can also
probe flash through DT.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agobrcm63xx: add pflash for remaining pflash equipped boards
Jonas Gorski [Tue, 7 Feb 2017 13:24:02 +0000 (14:24 +0100)]
brcm63xx: add pflash for remaining pflash equipped boards

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agobrcm63xx: do not require fixed partitions when probing from DT
Jonas Gorski [Tue, 7 Feb 2017 13:20:25 +0000 (14:20 +0100)]
brcm63xx: do not require fixed partitions when probing from DT

Allow the parser to be invoked from DT without fixed cfe/linux/nvram
partitions. This allows flash to be probed from DT also for multi
flash-size images.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agobrcm63xx: register SPI controllers through DT
Jonas Gorski [Tue, 7 Feb 2017 11:31:02 +0000 (12:31 +0100)]
brcm63xx: register SPI controllers through DT

Register SPI controllers through device tree. We will wire up the clocks
at a later stage.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agobrcm63xx: backport upstream solution for SPI message size limits
Jonas Gorski [Tue, 7 Feb 2017 11:01:46 +0000 (12:01 +0100)]
brcm63xx: backport upstream solution for SPI message size limits

Backport upstream solution for working around SPI controller maximum
message sizes.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agobrcm63xx: update flash of_node patches to full patch set
Jonas Gorski [Tue, 7 Feb 2017 10:59:07 +0000 (11:59 +0100)]
brcm63xx: update flash of_node patches to full patch set

Fixes missing of_node for SPI flash probed through devicetree.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agobrcm63xx: refresh kernel config
Jonas Gorski [Thu, 11 May 2017 11:58:13 +0000 (13:58 +0200)]
brcm63xx: refresh kernel config

Ensure the config is ordered and has all recent symbols.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agobuild: fix kernel refresh failure on first run
Jonas Gorski [Sat, 3 Jun 2017 11:17:16 +0000 (13:17 +0200)]
build: fix kernel refresh failure on first run

Override {HOST_}QUILT before making decisions based on it, else it will
cause target/linux/refresh to fail on first run.

Fixes: 36ba6237d6e3a23fbeadcc1812a892faa4b07cbe ("build: fix quilt for mixed package/host builds")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agolantiq: fix 0008-MIPS-lantiq-backport-old-timer-code.patch for Amazon-SE
Tino Reichardt [Sun, 7 May 2017 17:30:36 +0000 (19:30 +0200)]
lantiq: fix 0008-MIPS-lantiq-backport-old-timer-code.patch for Amazon-SE

The patch 0008 removes the vanilla kernel gptu.c of lantiq.
But the replacement file timer.c does not work Amazon-SE and
is also protected therefore with an CONFIG_SOC_AMAZON_SE :-)

This commit will re-activate the default vanilla kernel code
in gptu.c for Amazon-SE.

Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
[refresh patches and add same change for kernel 4.9]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
7 years agolantiq: fix lantiq_mei.c and amazonse.dsti for adsl modem firmware
Tino Reichardt [Tue, 28 Feb 2017 22:08:44 +0000 (23:08 +0100)]
lantiq: fix lantiq_mei.c and amazonse.dsti for adsl modem firmware

The ltq-adsl-mei package is used for 3 lantiq device types:
danube, amazon-se and ar9.

These different SoC's need also different definitions.

Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
[fix LTQ_USB_OC_INT for AR9 to match documentation]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
7 years agolantiq: add Allnet ALL0333CJ support
Tino Reichardt [Sun, 26 Feb 2017 20:29:37 +0000 (21:29 +0100)]
lantiq: add Allnet ALL0333CJ support

This patch adds support for the Allnet ADSL2+ Modem ALL0333CJ.

Specifications:
- SoC: Amazon-SE
- RAM: 16MB
- Storage: 4MB NOR FLash
- LEDs: Power, Ethernet, DSL (Sync)
- Buttons: 1x Reset Button (not currently supported, will be done)
- 1x Ethernet-Port: 1x RJ45 10/100BaseTX
- 1x WAN-Port: AnnexB & J, G.992.1(ADSL), G.992.3(ADSL2), G.992.5(ADSL2+)

Installation:
- can be done via telnet+tftp or serial console
- default passwords:
  - via telnet (root:admin)
  - via webinterface http://172.16.1.254:8235/ (admin:coolwhite)

Installation via telnet / tftp:
host: # your own host must have an tftpd daemon, then do this:
host: ifconfig eth0:172 172.16.1.1 up
host: # telnet to allnet modem, root:admin
host: telnet 172.16.1.254
modem: # kill this daemon, it spams your console
modem: killall dsl_cpe_control
modem: # change to some place in ram:
modem: cd /ramdisk/tftp_upload
modem: # load lede-lantiq-ase-ALL0333CJ-squashfs-sysupgrade.bin alias uImage
modem: tftp -g -r uImage 172.16.1.1
modem: # load these extra tools from your tftpd via:
modem: # source: https://github.com/mcmilk/uboot-utils/releases/download/0.1/mips32.tar.gz
modem: tftp -g -r flashwrite 172.16.1.1
modem: tftp -g -r fw_setenv 172.16.1.1
modem: tftp -g -r fw.conf 172.16.1.1
modem: ln -s fw_setenv fw_printenv
modem: chmod +x *
modem: ./fw_setenv disable_recovery y
modem: ./fw_setenv kernel_addr 0xb0010000
modem: ./flashwrite /dev/mtd/1 uImage 0

Installation via serial line at uboot:
uboot: # erase everything exept bootloader
uboot: protect on b0000000 +10000; protect on b03f0000 +10000
uboot: erase all
uboot: # get new firmware via tftp:
uboot: tftpboot 0x80100000 uImage; setenv kernel_addr 0xb0010000
uboot: # copy to flash:
uboot: cp.b 0x80100000 $(kernel_addr) $(filesize)
uboot: # disable proprietary image checking:
uboot: setenv disable_recovery=y; saveenv
uboot: # reboot with LEDE ;)
uboot: reset

Ethernet works as expected, DSL syncronization does not work properly
currently, I am working on this issue.

Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
7 years agolantiq: fix ifxmips_atm_amazon_se.c
Tino Reichardt [Tue, 28 Feb 2017 22:20:19 +0000 (23:20 +0100)]
lantiq: fix ifxmips_atm_amazon_se.c

Remove 6 defines, which were defined already some lines above.

Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
7 years agolantiq: enable Netgear DGN1000B image build
Tino Reichardt [Sun, 26 Feb 2017 20:28:28 +0000 (21:28 +0100)]
lantiq: enable Netgear DGN1000B image build

Enable the building of Netgear DGN1000B images. I have an
example device here, but it was not tested currently.
Also WLAN and USB is not ready in the moment.

This is just the proper way, so that developing on this
device is known to be done in the near future.

Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
7 years agolantiq: add Amazon-SE subtarget
Tino Reichardt [Sun, 26 Feb 2017 20:26:08 +0000 (21:26 +0100)]
lantiq: add Amazon-SE subtarget

Re-Add support for the Amazon-SE subtarget on Lantiq.

Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
7 years agolantiq: fix amazonse.dsti
Tino Reichardt [Sun, 26 Feb 2017 20:25:32 +0000 (21:25 +0100)]
lantiq: fix amazonse.dsti

Add missing memory@0 and localbus@0 sections.
Fix MEI and GPTU interrupt definitions.

Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
7 years agokernel: properly package 8250 serial PCI module
Daniel Golle [Sat, 3 Jun 2017 18:29:20 +0000 (20:29 +0200)]
kernel: properly package 8250 serial PCI module

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
7 years agoramips: enable PCIe on MT7688
Daniel Golle [Sat, 3 Jun 2017 18:24:11 +0000 (20:24 +0200)]
ramips: enable PCIe on MT7688

Submitted upstream as well, see
patchwork https://patchwork.linux-mips.org/patch/16223/

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
7 years agoLantiq: make possible to tweak DSL SRN from UCI
Andrea Merello [Sat, 13 May 2017 15:16:13 +0000 (17:16 +0200)]
Lantiq: make possible to tweak DSL SRN from UCI

This patch makes possible to tweak the downstream SNR margin on
Lantiq DSL devices.

The UCI parameter 'network.dsl.ds_snr_offset' is used to set the SNR
margin offset. It accepts values in range -50 to +50 in 0.1 dB units.

The SNR margin can thus be modified in range -5.0 to +5.0 dB in 0.1 dB
steps.

Currently this should only affect ADSL (not VDSL). It should be very
easy to make this work also on VDSL lines, but since I couldn't test
on VDSL lines this patch does not do that yet.

I have also a patch for LUCI about this, that I could submit.

Tested on FB3370 (Lantiq VR9) and Telecom Italia ADSL2+ line.

Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
7 years agolantiq: modified lantiq_dsl.sh status output of latency
Helge Mader [Wed, 31 May 2017 09:57:56 +0000 (11:57 +0200)]
lantiq: modified lantiq_dsl.sh status output of latency

Signed-off-by: Helge Mader <ma@dev.tdt.de>
7 years agolantiq: fix lantiq_dsl.sh status and lucistat output
Helge Mader [Wed, 31 May 2017 09:20:49 +0000 (11:20 +0200)]
lantiq: fix lantiq_dsl.sh status and lucistat output

Signed-off-by: Helge Mader <ma@dev.tdt.de>
7 years agomvebu: Add block device sd to default kernel config
Daniel Engberg [Fri, 2 Jun 2017 01:00:39 +0000 (03:00 +0200)]
mvebu: Add block device sd to default kernel config

Add block device sd to kernel config otherwise AHCI/eSATA devices won't get enumerated in /dev

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>