/*
* D-Link DIR-825 rev. B1 board support
*
- * Copyright (C) 2009 Lukas Kuna, Evkanet, s.r.o.
+ * Copyright (C) 2009-2011 Lukas Kuna, Evkanet, s.r.o.
*
* based on mach-wndr3700.c
*
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/delay.h>
-#include <linux/rtl8366s.h>
+#include <linux/rtl8366.h>
#include <asm/mach-ar71xx/ar71xx.h>
#define DIR825B1_GPIO_LED_BLUE_USB 0
#define DIR825B1_GPIO_LED_ORANGE_POWER 1
#define DIR825B1_GPIO_LED_BLUE_POWER 2
-#define DIR825B1_GPIO_LED_BLUE_POWERSAVE 4
+#define DIR825B1_GPIO_LED_BLUE_WPS 4
#define DIR825B1_GPIO_LED_ORANGE_PLANET 6
#define DIR825B1_GPIO_LED_BLUE_PLANET 11
#define DIR825B1_GPIO_BTN_RESET 3
-#define DIR825B1_GPIO_BTN_POWERSAVE 8
+#define DIR825B1_GPIO_BTN_WPS 8
#define DIR825B1_GPIO_RTL8366_SDA 5
#define DIR825B1_GPIO_RTL8366_SCK 7
-#define DIR825B1_BUTTONS_POLL_INTERVAL 20
+#define DIR825B1_KEYS_POLL_INTERVAL 20 /* msecs */
+#define DIR825B1_KEYS_DEBOUNCE_INTERVAL (3 * DIR825B1_KEYS_POLL_INTERVAL)
#define DIR825B1_CAL_LOCATION_0 0x1f661000
#define DIR825B1_CAL_LOCATION_1 0x1f665000
-#define DIR825B1_MAC_LOCATION_0 0x2ffa81b8
-#define DIR825B1_MAC_LOCATION_1 0x2ffa8370
+#define DIR825B1_MAC_LOCATION_0 0x1f66ffa0
+#define DIR825B1_MAC_LOCATION_1 0x1f66ffb4
#ifdef CONFIG_MTD_PARTITIONS
static struct mtd_partition dir825b1_partitions[] = {
.offset = 0,
.size = 0x040000,
.mask_flags = MTD_WRITEABLE,
- } , {
+ }, {
.name = "config",
.offset = 0x040000,
.size = 0x010000,
.mask_flags = MTD_WRITEABLE,
- } , {
+ }, {
.name = "firmware",
.offset = 0x050000,
.size = 0x610000,
- } , {
+ }, {
.name = "caldata",
.offset = 0x660000,
.size = 0x010000,
.mask_flags = MTD_WRITEABLE,
- } , {
+ }, {
.name = "unknown",
.offset = 0x670000,
.size = 0x190000,
static struct flash_platform_data dir825b1_flash_data = {
#ifdef CONFIG_MTD_PARTITIONS
- .parts = dir825b1_partitions,
- .nr_parts = ARRAY_SIZE(dir825b1_partitions),
+ .parts = dir825b1_partitions,
+ .nr_parts = ARRAY_SIZE(dir825b1_partitions),
#endif
};
.gpio = DIR825B1_GPIO_LED_BLUE_POWER,
.active_low = 1,
}, {
- .name = "dir825b1:blue:powersave",
- .gpio = DIR825B1_GPIO_LED_BLUE_POWERSAVE,
+ .name = "dir825b1:blue:wps",
+ .gpio = DIR825B1_GPIO_LED_BLUE_WPS,
.active_low = 1,
}, {
.name = "dir825b1:orange:planet",
}
};
-static struct gpio_button dir825b1_gpio_buttons[] __initdata = {
+static struct gpio_keys_button dir825b1_gpio_keys[] __initdata = {
{
.desc = "reset",
.type = EV_KEY,
.code = KEY_RESTART,
- .threshold = 3,
+ .debounce_interval = DIR825B1_KEYS_DEBOUNCE_INTERVAL,
.gpio = DIR825B1_GPIO_BTN_RESET,
.active_low = 1,
- } , {
- .desc = "powersave",
+ }, {
+ .desc = "wps",
.type = EV_KEY,
- .code = BTN_1,
- .threshold = 3,
- .gpio = DIR825B1_GPIO_BTN_POWERSAVE,
+ .code = KEY_WPS_BUTTON,
+ .debounce_interval = DIR825B1_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = DIR825B1_GPIO_BTN_WPS,
.active_low = 1,
}
};
-static struct rtl8366s_platform_data dir825b1_rtl8366s_data = {
- .gpio_sda = DIR825B1_GPIO_RTL8366_SDA,
- .gpio_sck = DIR825B1_GPIO_RTL8366_SCK,
+static struct rtl8366_initval dir825b1_rtl8366s_initvals[] = {
+ { .reg = 0x06, .val = 0x0108 },
+};
+
+static struct rtl8366_platform_data dir825b1_rtl8366s_data = {
+ .gpio_sda = DIR825B1_GPIO_RTL8366_SDA,
+ .gpio_sck = DIR825B1_GPIO_RTL8366_SCK,
+ .num_initvals = ARRAY_SIZE(dir825b1_rtl8366s_initvals),
+ .initvals = dir825b1_rtl8366s_initvals,
};
static struct platform_device dir825b1_rtl8366s_device = {
}
};
+static void dir825b1_read_ascii_mac(u8 *dest, unsigned int src_addr)
+{
+ int ret;
+ u8 *src = (u8 *)KSEG1ADDR(src_addr);
+
+ ret = sscanf(src, "%02hhx:%02hhx:%02hhx:%02hhx:%02hhx:%02hhx",
+ &dest[0], &dest[1], &dest[2],
+ &dest[3], &dest[4], &dest[5]);
+
+ if (ret != ETH_ALEN) memset(dest, 0, ETH_ALEN);
+}
+
static void __init dir825b1_setup(void)
{
- u8 *mac = (u8 *) KSEG1ADDR(DIR825B1_MAC_LOCATION_1);
+ u8 mac1[ETH_ALEN], mac2[ETH_ALEN];
+
+ dir825b1_read_ascii_mac(mac1, DIR825B1_MAC_LOCATION_0);
+ dir825b1_read_ascii_mac(mac2, DIR825B1_MAC_LOCATION_1);
- ar71xx_add_device_mdio(0x0);
+ ar71xx_add_device_mdio(0, 0x0);
- ar71xx_init_mac(ar71xx_eth0_data.mac_addr, mac, 1);
+ ar71xx_init_mac(ar71xx_eth0_data.mac_addr, mac1, 2);
ar71xx_eth0_data.mii_bus_dev = &dir825b1_rtl8366s_device.dev;
ar71xx_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
ar71xx_eth0_data.speed = SPEED_1000;
ar71xx_eth0_data.duplex = DUPLEX_FULL;
ar71xx_eth0_pll_data.pll_1000 = 0x11110000;
- ar71xx_init_mac(ar71xx_eth0_data.mac_addr, mac, 2);
+ ar71xx_init_mac(ar71xx_eth1_data.mac_addr, mac1, 3);
ar71xx_eth1_data.mii_bus_dev = &dir825b1_rtl8366s_device.dev;
ar71xx_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
ar71xx_eth1_data.phy_mask = 0x10;
ar71xx_add_device_leds_gpio(-1, ARRAY_SIZE(dir825b1_leds_gpio),
dir825b1_leds_gpio);
- ar71xx_add_device_gpio_buttons(-1, DIR825B1_BUTTONS_POLL_INTERVAL,
- ARRAY_SIZE(dir825b1_gpio_buttons),
- dir825b1_gpio_buttons);
+ ar71xx_register_gpio_keys_polled(-1, DIR825B1_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(dir825b1_gpio_keys),
+ dir825b1_gpio_keys);
ar71xx_add_device_usb();
platform_device_register(&dir825b1_rtl8366s_device);
- ap94_pci_init((u8 *) KSEG1ADDR(DIR825B1_CAL_LOCATION_0),
- (u8 *) KSEG1ADDR(DIR825B1_MAC_LOCATION_0),
- (u8 *) KSEG1ADDR(DIR825B1_CAL_LOCATION_1),
- (u8 *) KSEG1ADDR(DIR825B1_MAC_LOCATION_1));
+ ap94_pci_setup_wmac_led_pin(0, 5);
+ ap94_pci_setup_wmac_led_pin(1, 5);
+
+ ap94_pci_init((u8 *) KSEG1ADDR(DIR825B1_CAL_LOCATION_0), mac1,
+ (u8 *) KSEG1ADDR(DIR825B1_CAL_LOCATION_1), mac2);
}
MIPS_MACHINE(AR71XX_MACH_DIR_825_B1, "DIR-825-B1", "D-Link DIR-825 rev. B1",
projects / openwrt / openwrt.git / blobdiff