ipq40xx: add support for Netgear SRR60/SRS60 and RBR50/RBS50

[openwrt/openwrt.git] / target / linux / ipq40xx / base-files / etc / board.d / 02_network

diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
old mode 100755 (executable)
new mode 100644 (file)
index 4361b7c..50b460e
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -1,4 +1,3 @@
-#!/bin/sh
 #
 # Copyright (c) 2015 The Linux Foundation. All rights reserved.
 # Copyright (c) 2011-2015 OpenWrt.org
@@ -18,6 +17,7 @@ ipq40xx_setup_interfaces()
        engenius,emr3500|\
        engenius,ens620ext|\
        luma,wrtq-329acn|\
+       netgear,wac510|\
        plasmacloud,pa1200|\
        plasmacloud,pa2200)
                ucidef_set_interfaces_lan_wan "eth0" "eth1"
@@ -29,6 +29,7 @@ ipq40xx_setup_interfaces()
        engenius,eap1300|\
        engenius,emd1|\
        meraki,mr33|\
+       mikrotik,sxtsq-5-ac|\
        netgear,ex6100v2|\
        netgear,ex6150v2|\
        zyxel,wre6606)
@@ -48,6 +49,7 @@ ipq40xx_setup_interfaces()
                ucidef_set_interfaces_lan_wan "eth1" "eth0"
                ;;
        asus,rt-ac58u|\
+       mikrotik,hap-ac2|\
        zyxel,nbg6617)
                ucidef_set_interfaces_lan_wan "eth0" "eth1"
                ucidef_add_switch "switch0" \
@@ -63,7 +65,7 @@ ipq40xx_setup_interfaces()
                ;;
        avm,fritzbox-7530)
                ucidef_add_switch "switch0" \
-                       "0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
+                       "0u@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
                ;;
        avm,fritzrepeater-3000)
                ucidef_add_switch "switch0" \
@@ -84,11 +86,15 @@ ipq40xx_setup_interfaces()
                ucidef_add_switch "switch0" \
                        "0u@eth0" "3:lan" "4:lan"
                ;;
+       devolo,magic-2-wifi-next)
+               ucidef_set_interface_lan "eth0 eth1 eth2"
+               ;;
        ezviz,cs-w3-wd1200g-eup)
                ucidef_set_interfaces_lan_wan "eth0" "eth1"
                ucidef_add_switch "switch0" \
                        "0u@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "0u@eth1" "5:wan"
                ;;
+       glinet,gl-ap1300 |\
        glinet,gl-b1300 |\
        glinet,gl-s1300)
                ucidef_set_interfaces_lan_wan "eth0" "eth1"
@@ -100,6 +106,14 @@ ipq40xx_setup_interfaces()
                        "0u@eth0" "3:lan:2" "4:lan:1"
                ucidef_set_interface_wan "eth1"
                ;;
+       netgear,rbr50|\
+       netgear,rbs50|\
+       netgear,srr60|\
+       netgear,srs60)
+               ucidef_add_switch "switch0" \
+                       "0u@eth0" "2:lan" "3:lan" "4:lan"
+               ucidef_set_interface_wan "eth1"
+               ;;
        qxwlan,e2600ac-c1 |\
        qxwlan,e2600ac-c2)
                ucidef_set_interfaces_lan_wan "eth0" "eth1"
@@ -137,6 +151,10 @@ ipq40xx_setup_macs()
        cilab,meshpoint-one)
                label_mac=$(mtd_get_mac_binary "ART" 0x1006)
                ;;
+       devolo,magic-2-wifi-next)
+               lan_mac=$(mtd_get_mac_ascii APPSBLENV MacAddress0)
+               label_mac=$lan_mac
+               ;;
        dlink,dap-2610)
                lan_mac=$(mtd_get_mac_ascii bdcfg lanmac)
                label_mac=$lan_mac
@@ -162,6 +180,15 @@ ipq40xx_setup_macs()
                wan_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
                lan_mac=$(macaddr_add "$wan_mac" 1)
                ;;
+       mikrotik,hap-ac2)
+               wan_mac=$(cat /sys/firmware/mikrotik/hard_config/mac_base)
+               lan_mac=$(macaddr_add $wan_mac 1)
+               label_mac="$wan_mac"
+               ;;
+       mikrotik,sxtsq-5-ac)
+               lan_mac=$(cat /sys/firmware/mikrotik/hard_config/mac_base)
+               label_mac="$lan_mac"
+               ;;
        esac
 
        [ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac