include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk
+DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION
+
define Device/Default
PROFILES := Default
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
KERNEL_NAME := Image
endef
+define Device/FitzImage
+ KERNEL_SUFFIX := -fit-zImage.itb
+ KERNEL = kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb
+ KERNEL_NAME := zImage
+endef
+
define Device/UbiFit
KERNEL_IN_UBI := 1
IMAGES := nand-factory.ubi nand-sysupgrade.bin
IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata
endef
+define Device/DniImage
+ KERNEL_SUFFIX := -fit-uImage.itb
+ KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
+ KERNEL_NAME := Image
+ NETGEAR_BOARD_ID :=
+ NETGEAR_HW_ID :=
+ IMAGES := factory.img sysupgrade.bin
+ IMAGE/factory.img := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | netgear-dni
+ IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | append-metadata
+endef
+DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
+
+define Build/SenaoFW
+ -$(STAGING_DIR_HOST)/bin/mksenaofw \
+ -n $(BOARD_NAME) -r $(VENDOR_ID) -p $(1) \
+ -c $(DATECODE) -w $(2) -x $(CW_VER) -t 0 \
+ -e $@ \
+ -o $@.new
+ @cp $@.new $@
+endef
+
+define Device/8dev_jalapeno-common
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+endef
+
+define Device/8dev_jalapeno
+ $(call Device/8dev_jalapeno-common)
+ DEVICE_VENDOR := 8devices
+ DEVICE_MODEL := Jalapeno
+ DEVICE_DTS := qcom-ipq4018-jalapeno
+endef
+TARGET_DEVICES += 8dev_jalapeno
+
+define Device/alfa-network_ap120c-ac
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ DEVICE_VENDOR := ALFA Network
+ DEVICE_MODEL := AP120C-AC
+ DEVICE_DTS := qcom-ipq4018-ap120c-ac
+ DEVICE_PACKAGES := kmod-usb-acm \
+ kmod-tpm-i2c-atmel uboot-envtools
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ IMAGE_SIZE := 65536k
+ IMAGES := nand-factory.bin nand-sysupgrade.bin
+ IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
+endef
+TARGET_DEVICES += alfa-network_ap120c-ac
+
+define Device/aruba_ap-303
+ $(call Device/FitImageLzma)
+ DEVICE_VENDOR := Aruba
+ DEVICE_MODEL := AP-303
+ DEVICE_DTS := qcom-ipq4029-ap-303
+ DEVICE_PACKAGES := ipq-wifi-aruba_ap-303
+ IMAGES := sysupgrade.bin
+endef
+TARGET_DEVICES += aruba_ap-303
+
+define Device/asus_map-ac2200
+ $(call Device/FitImageLzma)
+ DEVICE_VENDOR := ASUS
+ DEVICE_MODEL := Lyra (MAP-AC2200)
+ DEVICE_DTS := qcom-ipq4019-map-ac2200
+ IMAGES := sysupgrade.bin
+ DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-ath3k
+endef
+TARGET_DEVICES += asus_map-ac2200
define Device/asus_rt-ac58u
$(call Device/FitImageLzma)
+ DEVICE_VENDOR := ASUS
+ DEVICE_MODEL := RT-AC58U
DEVICE_DTS := qcom-ipq4018-rt-ac58u
BLOCKSIZE := 128k
PAGESIZE := 2048
DTB_SIZE := 65536
- DEVICE_TITLE := Asus RT-AC58U
IMAGE_SIZE := 20439364
FILESYSTEMS := squashfs
# Someone - in their infinite wisdom - decided to put the firmware
# string and call it a day.... Yeah, we do the latter!
UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC58U')
IMAGES := sysupgrade.bin
- DEVICE_PACKAGES := ipq-wifi-asus_rt-ac58u kmod-usb-ledtrig-usbport
+ DEVICE_PACKAGES := kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += asus_rt-ac58u
define Device/avm_fritzbox-4040
$(call Device/FitImageLzma)
- DEVICE_DTS := qcom-ipq4019-fritz4040
+ DEVICE_VENDOR := AVM
+ DEVICE_MODEL := FRITZ!Box 4040
+ DEVICE_DTS := qcom-ipq4018-fritz4040
BOARD_NAME := fritz4040
- DEVICE_TITLE := AVM Fritz!Box 4040
- IMAGE_SIZE := 29753344
- IMAGES = sysupgrade.bin
+ IMAGE_SIZE := 29056k
+ UBOOT_PATH := $(STAGING_DIR_IMAGE)/uboot-fritz4040.bin
+ UBOOT_PARTITION_SIZE := 524288
+ IMAGES = eva.bin sysupgrade.bin
+ IMAGE/eva.bin := append-uboot | pad-to $$$$(UBOOT_PARTITION_SIZE) | append-kernel | append-rootfs | pad-rootfs
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
- DEVICE_PACKAGES := ipq-wifi-avm_fritzbox-4040 fritz-tffs fritz-caldata u-boot-fritz4040
+ DEVICE_PACKAGES := fritz-tffs fritz-caldata
endef
TARGET_DEVICES += avm_fritzbox-4040
+define Device/avm_fritzbox-7530
+ $(call Device/FitImageLzma)
+ DEVICE_VENDOR := AVM
+ DEVICE_MODEL := FRITZ!Box 7530
+ DEVICE_DTS := qcom-ipq4019-fritzbox-7530
+ DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand
+ IMAGES := sysupgrade.bin
+endef
+TARGET_DEVICES += avm_fritzbox-7530
+
+define Device/avm_fritzrepeater-1200
+ $(call Device/FitImageLzma)
+ DEVICE_VENDOR := AVM
+ DEVICE_MODEL := FRITZ!Repeater 1200
+ DEVICE_DTS := qcom-ipq4019-fritzrepeater-1200
+ DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand ipq-wifi-avm_fritzrepeater-1200
+ IMAGES := sysupgrade.bin
+endef
+TARGET_DEVICES += avm_fritzrepeater-1200
+
+define Device/avm_fritzrepeater-3000
+ $(call Device/FitImageLzma)
+ DEVICE_VENDOR := AVM
+ DEVICE_MODEL := FRITZ!Repeater 3000
+ DEVICE_DTS := qcom-ipq4019-fritzrepeater-3000
+ DEVICE_PACKAGES := ath10k-firmware-qca9984-ct fritz-caldata fritz-tffs-nand
+ IMAGES := sysupgrade.bin
+endef
+TARGET_DEVICES += avm_fritzrepeater-3000
+
+define Device/cilab_meshpoint-one
+ $(call Device/8dev_jalapeno-common)
+ DEVICE_DTS := qcom-ipq4018-meshpoint-one
+ DEVICE_VENDOR := Crisis Innovation Lab
+ DEVICE_MODEL := MeshPoint.One
+ DEVICE_PACKAGES := kmod-i2c-gpio kmod-iio-bmp280-i2c kmod-hwmon-ina2xx kmod-rtc-pcf2127
+endef
+TARGET_DEVICES += cilab_meshpoint-one
+
+define Device/compex_wpj419
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ DEVICE_VENDOR := Compex
+ DEVICE_MODEL := WPJ419
+ DEVICE_DTS := qcom-ipq4019-wpj419
+ DEVICE_DTS_CONFIG := config@12
+ KERNEL_INSTALL := 1
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ FILESYSTEMS := squashfs
+endef
+TARGET_DEVICES += compex_wpj419
+
+define Device/compex_wpj428
+ $(call Device/FitImage)
+ DEVICE_VENDOR := Compex
+ DEVICE_MODEL := WPJ428
+ DEVICE_DTS := qcom-ipq4028-wpj428
+ DEVICE_DTS_CONFIG := config@4
+ BLOCKSIZE := 64k
+ IMAGE_SIZE := 31232k
+ KERNEL_SIZE := 4096k
+ IMAGES = sysupgrade.bin
+ IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
+ DEVICE_PACKAGES := kmod-gpio-beeper
+endef
+TARGET_DEVICES += compex_wpj428
+
+define Device/engenius_eap1300
+ $(call Device/FitImage)
+ DEVICE_VENDOR := EnGenius
+ DEVICE_MODEL := EAP1300
+ DEVICE_DTS_CONFIG := config@4
+ BOARD_NAME := eap1300
+ DEVICE_DTS := qcom-ipq4018-eap1300
+ KERNEL_SIZE := 5120k
+ IMAGE_SIZE := 25344k
+ IMAGES := sysupgrade.bin
+ IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
+endef
+TARGET_DEVICES += engenius_eap1300
+
+define Device/engenius_ens620ext
+ $(call Device/FitImage)
+ DEVICE_VENDOR := EnGenius
+ DEVICE_MODEL := ENS620EXT
+ DEVICE_DTS := qcom-ipq4018-ens620ext
+ DEVICE_DTS_CONFIG := config@4
+ BLOCKSIZE := 64k
+ PAGESIZE := 256
+ BOARD_NAME := ENS620EXT
+ VENDOR_ID := 0x0101
+ PRODUCT_ID := 0x79
+ PRODUCT_ID_NEW := 0xA4
+ DATECODE := 190507
+ FW_VER := 3.1.2
+ FW_VER_NEW := 3.5.6
+ CW_VER := 1.8.99
+ IMAGE_SIZE := 21312k
+ KERNEL_SIZE := 5120k
+ FILESYSTEMS := squashfs
+ IMAGES := sysupgrade.bin factory_30.bin factory_35.bin
+ IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | append-metadata
+ IMAGE/factory_30.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | SenaoFW $$$$(PRODUCT_ID) $$$$(FW_VER)
+ IMAGE/factory_35.bin := qsdk-ipq-factory-nor | check-size $$$$(IMAGE_SIZE) | SenaoFW $$$$(PRODUCT_ID_NEW) $$$$(FW_VER_NEW)
+endef
+TARGET_DEVICES += engenius_ens620ext
+
define Device/glinet_gl-b1300
$(call Device/FitImage)
- DEVICE_TITLE := GL.iNet GL-B1300
+ DEVICE_VENDOR := GL.iNet
+ DEVICE_MODEL := GL-B1300
BOARD_NAME := gl-b1300
DEVICE_DTS := qcom-ipq4029-gl-b1300
KERNEL_SIZE := 4096k
IMAGE_SIZE := 26624k
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel |append-rootfs | pad-rootfs | append-metadata
- DEVICE_PACKAGES := ipq-wifi-glinet_gl-b1300
endef
TARGET_DEVICES += glinet_gl-b1300
+define Device/linksys_ea6350v3
+ # The Linksys EA6350v3 has a uboot bootloader that does not
+ # support either booting lzma kernel images nor booting UBI
+ # partitions. This uboot, however, supports raw kernel images and
+ # gzipped images.
+ #
+ # As for the time of writing this, the device will boot the kernel
+ # from a fixed address with a fixed length of 3MiB. Also, the
+ # device has a hard-coded kernel command line that requieres the
+ # rootfs and alt_rootfs to be in mtd11 and mtd13 respectively.
+ # Oh... and the kernel partition overlaps with the rootfs
+ # partition (the same for alt_kernel and alt_rootfs).
+ #
+ # If you are planing re-partitioning the device, you may want to
+ # keep those details in mind:
+ # 1. The kernel adresses you should honor are 0x00000000 and
+ # 0x02800000 respectively.
+ # 2. The kernel size (plus the dtb) cannot exceed 3.00MiB in size.
+ # 3. You can use 'zImage', but not a raw 'Image' packed with lzma.
+ # 4. The kernel command line from uboot is harcoded to boot with
+ # rootfs either in mtd11 or mtd13.
+ $(call Device/FitzImage)
+ DEVICE_VENDOR := Linksys
+ DEVICE_MODEL := EA6350
+ DEVICE_VARIANT := v3
+ DEVICE_DTS := qcom-ipq4018-ea6350v3
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ KERNEL_SIZE := 3072k
+ IMAGE_SIZE := 37888k
+ UBINIZE_OPTS := -E 5
+ IMAGES := factory.bin sysupgrade.bin
+ IMAGE/factory.bin := append-kernel | append-uImage-fakehdr filesystem | pad-to $$$${KERNEL_SIZE} | append-ubi | linksys-image type=EA6350v3
+ DEVICE_PACKAGES := uboot-envtools
+endef
+TARGET_DEVICES += linksys_ea6350v3
+
+define Device/linksys_ea8300
+ $(call Device/FitzImage)
+ DEVICE_VENDOR := Linksys
+ DEVICE_MODEL := EA8300
+ DEVICE_DTS := qcom-ipq4019-linksys_ea8300
+ KERNEL_SIZE := 3072k
+ IMAGE_SIZE := 87040k
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
+ IMAGES := sysupgrade.bin factory.bin
+ IMAGE/factory.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-ubi | linksys-image type=EA8300
+ DEVICE_PACKAGES := uboot-envtools ath10k-firmware-qca9888-ct ipq-wifi-linksys_ea8300 kmod-usb-ledtrig-usbport
+endef
+TARGET_DEVICES += linksys_ea8300
+
+define Device/meraki_mr33
+ $(call Device/FitImage)
+ DEVICE_VENDOR := Cisco Meraki
+ DEVICE_MODEL := MR33
+ DEVICE_DTS := qcom-ipq4029-mr33
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ IMAGES = sysupgrade.bin
+ DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887-ct
+endef
+TARGET_DEVICES += meraki_mr33
+
+define Device/netgear_ex61x0v2
+ $(call Device/DniImage)
+ DEVICE_DTS_CONFIG := config@4
+ NETGEAR_BOARD_ID := EX6150v2series
+ NETGEAR_HW_ID := 29765285+16+0+128+2x2
+endef
+
+define Device/netgear_ex6100v2
+ $(call Device/netgear_ex61x0v2)
+ DEVICE_VENDOR := Netgear
+ DEVICE_MODEL := EX6100
+ DEVICE_VARIANT := v2
+ DEVICE_DTS := qcom-ipq4018-ex6100v2
+endef
+TARGET_DEVICES += netgear_ex6100v2
+
+define Device/netgear_ex6150v2
+ $(call Device/netgear_ex61x0v2)
+ DEVICE_VENDOR := Netgear
+ DEVICE_MODEL := EX6150
+ DEVICE_VARIANT := v2
+ DEVICE_DTS := qcom-ipq4018-ex6150v2
+endef
+TARGET_DEVICES += netgear_ex6150v2
+
define Device/openmesh_a42
$(call Device/FitImageLzma)
+ DEVICE_VENDOR := OpenMesh
+ DEVICE_MODEL := A42
DEVICE_DTS := qcom-ipq4018-a42
+ DEVICE_DTS_CONFIG := config@om.a42
BLOCKSIZE := 64k
- SUPPORTED_DEVICES := openmesh,a42
- DEVICE_TITLE := OpenMesh A42
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
IMAGE_SIZE := 15616k
IMAGES = factory.bin sysupgrade.bin
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A42
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
- DEVICE_PACKAGES := ath10k-firmware-qca4019 uboot-envtools
+ DEVICE_PACKAGES := uboot-envtools
endef
TARGET_DEVICES += openmesh_a42
+define Device/openmesh_a62
+ $(call Device/FitImageLzma)
+ DEVICE_VENDOR := OpenMesh
+ DEVICE_MODEL := A62
+ DEVICE_DTS := qcom-ipq4019-a62
+ DEVICE_DTS_CONFIG := config@om.a62
+ BLOCKSIZE := 64k
+ KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
+ IMAGE_SIZE := 15552k
+ IMAGES = factory.bin sysupgrade.bin
+ IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A62
+ IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
+ DEVICE_PACKAGES := ath10k-firmware-qca9888-ct uboot-envtools
+endef
+
+TARGET_DEVICES += openmesh_a62
+
define Device/qcom_ap-dk01.1-c1
- DEVICE_TITLE := QCA AP-DK01.1-C1
+ DEVICE_VENDOR := Qualcomm Atheros
+ DEVICE_MODEL := AP-DK01.1
+ DEVICE_VARIANT := C1
BOARD_NAME := ap-dk01.1-c1
DEVICE_DTS := qcom-ipq4019-ap.dk01.1-c1
KERNEL_INSTALL := 1
$(call Device/FitImage)
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata
- DEVICE_PACKAGES := ath10k-firmware-qca4019
endef
TARGET_DEVICES += qcom_ap-dk01.1-c1
define Device/qcom_ap-dk04.1-c1
$(call Device/FitImage)
$(call Device/UbiFit)
+ DEVICE_VENDOR := Qualcomm Atheros
+ DEVICE_MODEL := AP-DK04.1
+ DEVICE_VARIANT := C1
DEVICE_DTS := qcom-ipq4019-ap.dk04.1-c1
KERNEL_INSTALL := 1
KERNEL_SIZE := 4048k
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ap-dk04.1-c1
- DEVICE_TITLE := QCA AP-DK04.1-C1
endef
TARGET_DEVICES += qcom_ap-dk04.1-c1
+define Device/qxwlan_e2600ac-c1
+ $(call Device/FitImage)
+ DEVICE_VENDOR := Qxwlan
+ DEVICE_MODEL := E2600AC
+ DEVICE_VARIANT := C1
+ BOARD_NAME := e2600ac-c1
+ DEVICE_DTS := qcom-ipq4019-qxwlan-e2600ac-c1
+ KERNEL_SIZE := 4096k
+ IMAGE_SIZE := 31232k
+ IMAGES := sysupgrade.bin
+ IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
+ DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
+endef
+TARGET_DEVICES += qxwlan_e2600ac-c1
+
+define Device/qxwlan_e2600ac-c2
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ DEVICE_VENDOR := Qxwlan
+ DEVICE_MODEL := E2600AC
+ DEVICE_VARIANT := C2
+ DEVICE_DTS := qcom-ipq4019-qxwlan-e2600ac-c2
+ KERNEL_INSTALL := 1
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
+endef
+TARGET_DEVICES += qxwlan_e2600ac-c2
+
+define Device/unielec_u4019-32m
+ $(call Device/FitImage)
+ DEVICE_VENDOR := Unielec
+ DEVICE_MODEL := U4019
+ DEVICE_VARIANT := 32M
+ BOARD_NAME := u4019-32m
+ DEVICE_DTS := qcom-ipq4019-unielec-u4019-32m
+ KERNEL_SIZE := 4096k
+ IMAGE_SIZE := 31232k
+ IMAGES := sysupgrade.bin
+ IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
+endef
+TARGET_DEVICES += unielec_u4019-32m
+
+define Device/zyxel_nbg6617
+ $(call Device/FitImageLzma)
+ DEVICE_VENDOR := ZyXEL
+ DEVICE_MODEL := NBG6617
+ DEVICE_DTS := qcom-ipq4018-nbg6617
+ ROOTFS_SIZE := 24960k
+ RAS_BOARD := NBG6617
+ RAS_ROOTFS_SIZE := 19840k
+ RAS_VERSION := "$(VERSION_DIST) $(REVISION)"
+ IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
+ IMAGES := sysupgrade.bin factory.bin
+# The ZyXEL firmware allows flashing thru the web-gui only when the rootfs is
+# at least as large as the one of the initial firmware image (not the current
+# one on the device). This only applies to the Web-UI, the bootlaoder ignores
+# this minimum-size. However, the larger image can be flashed both ways.
+ IMAGE/factory.bin := append-rootfs | pad-rootfs | pad-to 64k | check-size $$$$(ROOTFS_SIZE) | zyxel-ras-image separate-kernel
+ IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | check-size $$$$(ROOTFS_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
+ DEVICE_PACKAGES := uboot-envtools kmod-usb-ledtrig-usbport
+endef
+TARGET_DEVICES += zyxel_nbg6617
+
+define Device/zyxel_wre6606
+ $(call Device/FitImage)
+ DEVICE_VENDOR := ZyXEL
+ DEVICE_MODEL := WRE6606
+ DEVICE_DTS_CONFIG := config@4
+ DEVICE_DTS := qcom-ipq4018-wre6606
+ IMAGES := sysupgrade.bin
+ IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
+endef
+TARGET_DEVICES += zyxel_wre6606
+
$(eval $(call BuildImage))