lantiq: remove "init" kernel command line parameter from bootargs

[openwrt/openwrt.git] / target / linux / lantiq / dts / BTHOMEHUBV3A.dts

diff --git a/target/linux/lantiq/dts/BTHOMEHUBV3A.dts b/target/linux/lantiq/dts/BTHOMEHUBV3A.dts
index 78799977272129416d606c8354f02dff99ed6e53..2cd098905da90e0f1c85cfa1d07e415448605537 100644 (file)
--- a/target/linux/lantiq/dts/BTHOMEHUBV3A.dts
+++ b/target/linux/lantiq/dts/BTHOMEHUBV3A.dts
@@ -1,14 +1,12 @@
 /dts-v1/;
 
-/include/ "ar9.dtsi"
+#include "ar9.dtsi"
+
+#include <dt-bindings/input/input.h>
 
 / {
        model = "BTHOMEHUBV3A - BT Home Hub 3A";  /* SoC: Lantiq ar9 @ 333MHz */
 
-       chosen {
-               bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
-       };
-
        aliases {
                led-boot = &power_orange;
                led-failsafe = &power_red;
@@ -25,20 +23,12 @@
        sram@1F000000 {
                vmmc@107000 {
                        status = "okay";
-                       gpios = <&gpio 31 0>;
+                       gpios = <&gpio 31 GPIO_ACTIVE_HIGH>;
                };
        };
 
        fpi@10000000 {
-               #address-cells = <1>;
-               #size-cells = <1>;
                localbus@0 {
-                       #address-cells = <2>;
-                       #size-cells = <1>;
-                       ranges = <0 0 0x0 0x3ffffff /* addrsel0 */
-                               1 0 0x4000000 0x4000010>; /* addsel1 */
-                       compatible = "lantiq,localbus", "simple-bus";
-
                        nand-parts@0 {            /* NAND Flash: Samsung K9F5608U0D-JIB0 32MB */
                                compatible = "gen_nand", "lantiq,nand-xway";
                                lantiq,cs = <1>;
@@ -81,24 +71,12 @@
                                        };
                                };
                        };
-
-                       ath9k_eep {
-                               compatible = "ath9k,eeprom";
-                               ath,eep-flash = <&ath9k_cal 0x0000>;
-                               ath,pci-slot = <14>;
-                               ath,eep-endian;
-                       };
                };
 
                gpio: pinmux@E100B10 {
-                       compatible = "lantiq,pinctrl-xr9";
                        pinctrl-names = "default";
                        pinctrl-0 = <&state_default>;
 
-                       #gpio-cells = <2>;
-                       gpio-controller;
-                       reg = <0xE100B10 0xA0>;
-
                        state_default: pinmux {
                                nand_out {
                                        lantiq,groups = "nand cle", "nand ale";
@@ -143,14 +121,8 @@
 
                ifxhcd@E101000 {
                        status = "okay";
-                       gpios = <&gpio 33 0>;
+                       gpios = <&gpio 33 GPIO_ACTIVE_HIGH>;
                };
-
-               pci@E105400 {
-                       status = "okay";
-                       gpio-reset = <&gpio 21 0>;
-               };
-
        };
 
        gpio-keys-polled {
@@ -160,18 +132,18 @@
                poll-interval = <100>;
                reset {
                        label = "reset";
-                       gpios = <&gpio 54 1>;
-                       linux,code = <0x198>;
+                       gpios = <&gpio 54 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RESTART>;
                };
                restart {
                        label = "restart";
-                       gpios = <&gpio 52 1>;
-                       linux,code = <0x198>;
+                       gpios = <&gpio 52 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_POWER>;
                };
                wps {
                        label = "wps";
-                       gpios = <&gpio 53 1>;
-                       linux,code = <0x211>;
+                       gpios = <&gpio 53 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_WPS_BUTTON>;
                };
        };
 
@@ -180,43 +152,52 @@
 
                wireless-red {
                        label = "bthomehubv3a:red:wireless";
-                       gpios = <&gpio 2 1>;
+                       gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
                };
                wireless-orange {
                        label = "bthomehubv3a:orange:wireless";
-                       gpios = <&gpio 6 1>;
+                       gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
                };
                wireless_blue: wireless-blue {
                        label = "bthomehubv3a:blue:wireless";
-                       gpios = <&gpio 9 1>;
+                       gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
                };
 
                broadband-red {
                        label = "bthomehubv3a:red:broadband";
-                       gpios = <&gpio 11 1>;
+                       gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
                };
                broadband-orange {
                        label = "bthomehubv3a:orange:broadband";
-                       gpios = <&gpio 0 1>;
+                       gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
                };
                broadband_blue: broadband-blue {
                        label = "bthomehubv3a:blue:broadband";
-                       gpios = <&gpio 12 1>;
+                       gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
                };
 
                power_red: power-red {
                        label = "bthomehubv3a:red:power";
-                       gpios = <&gpio 14 1>;
+                       gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
                };
                power_orange: power-orange {
                        label = "bthomehubv3a:orange:power";
-                       gpios = <&gpio 5 1>;
+                       gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
                        default-state = "keep";
                };
                power_blue: power-blue {
                        label = "bthomehubv3a:blue:power";
-                       gpios = <&gpio 1 1>;
+                       gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
                };
        };
 };
 
+&pci0 {
+       status = "okay";
+       gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
+
+       ath9k@7000 {
+               reg = <0x7000 0 0 0 0>;
+               qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */
+       };
+};