lantiq: remove "init" kernel command line parameter from bootargs

[openwrt/openwrt.git] / target / linux / lantiq / dts / BTHOMEHUBV3A.dts

diff --git a/target/linux/lantiq/dts/BTHOMEHUBV3A.dts b/target/linux/lantiq/dts/BTHOMEHUBV3A.dts
index 996d5b2abff792ecbde79f637996646a9624ef54..2cd098905da90e0f1c85cfa1d07e415448605537 100644 (file)
--- a/target/linux/lantiq/dts/BTHOMEHUBV3A.dts
+++ b/target/linux/lantiq/dts/BTHOMEHUBV3A.dts
@@ -2,13 +2,11 @@
 
 #include "ar9.dtsi"
 
+#include <dt-bindings/input/input.h>
+
 / {
        model = "BTHOMEHUBV3A - BT Home Hub 3A";  /* SoC: Lantiq ar9 @ 333MHz */
 
-       chosen {
-               bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
-       };
-
        aliases {
                led-boot = &power_orange;
                led-failsafe = &power_red;
@@ -30,15 +28,7 @@
        };
 
        fpi@10000000 {
-               #address-cells = <1>;
-               #size-cells = <1>;
                localbus@0 {
-                       #address-cells = <2>;
-                       #size-cells = <1>;
-                       ranges = <0 0 0x0 0x3ffffff /* addrsel0 */
-                               1 0 0x4000000 0x4000010>; /* addsel1 */
-                       compatible = "lantiq,localbus", "simple-bus";
-
                        nand-parts@0 {            /* NAND Flash: Samsung K9F5608U0D-JIB0 32MB */
                                compatible = "gen_nand", "lantiq,nand-xway";
                                lantiq,cs = <1>;
@@ -81,24 +71,12 @@
                                        };
                                };
                        };
-
-                       ath9k_eep {
-                               compatible = "ath9k,eeprom";
-                               ath,eep-flash = <&ath9k_cal 0x0000>;
-                               ath,pci-slot = <14>;
-                               ath,eep-endian;
-                       };
                };
 
                gpio: pinmux@E100B10 {
-                       compatible = "lantiq,pinctrl-xr9";
                        pinctrl-names = "default";
                        pinctrl-0 = <&state_default>;
 
-                       #gpio-cells = <2>;
-                       gpio-controller;
-                       reg = <0xE100B10 0xA0>;
-
                        state_default: pinmux {
                                nand_out {
                                        lantiq,groups = "nand cle", "nand ale";
@@ -145,12 +123,6 @@
                        status = "okay";
                        gpios = <&gpio 33 GPIO_ACTIVE_HIGH>;
                };
-
-               pci@E105400 {
-                       status = "okay";
-                       gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
-               };
-
        };
 
        gpio-keys-polled {
@@ -166,7 +138,7 @@
                restart {
                        label = "restart";
                        gpios = <&gpio 52 GPIO_ACTIVE_LOW>;
-                       linux,code = <KEY_RESTART>;
+                       linux,code = <KEY_POWER>;
                };
                wps {
                        label = "wps";
@@ -220,3 +192,12 @@
        };
 };
 
+&pci0 {
+       status = "okay";
+       gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
+
+       ath9k@7000 {
+               reg = <0x7000 0 0 0 0>;
+               qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */
+       };
+};