+// SPDX-License-Identifier: BSD-3-Clause
/*
- * BSD LICENSE
- *
* Copyright(c) 2017 Kristian Evensen <kristian.evensen@gmail.com>.
* All rights reserved.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- * * Redistributions of source code must retain the above copyright
- * notice, this list of conditions and the following disclaimer.
- * * Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in
- * the documentation and/or other materials provided with the
- * distribution.
- * * Neither the name of Broadcom Corporation nor the names of its
- * contributors may be used to endorse or promote products derived
- * from this software without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
- * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
- * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
- * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
- * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
- * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
-/dts-v1/;
-
#include "mt7620a.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
/ {
compatible = "sanlinking,d240", "ralink,mt7620a-soc";
compatible = "gpio-leds";
led_power: power {
- label = "d240:blue:power";
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_BLUE>;
gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
};
usb {
- label = "d240:blue:usb";
+ function = LED_FUNCTION_USB;
+ color = <LED_COLOR_ID_BLUE>;
gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
trigger-sources = <&ohci_port1>, <&ehci_port1>;
linux,default-trigger = "usbport";
};
air {
- label = "d240:blue:wifi";
+ label = "blue:wifi";
gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
};
};
&spi0 {
status = "okay";
- en25q128@0 {
+ flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <10000000>;
label = "factory";
reg = <0x40000 0x10000>;
read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ eeprom_factory_0: eeprom@0 {
+ reg = <0x0 0x200>;
+ };
+
+ macaddr_factory_4: macaddr@4 {
+ reg = <0x4 0x6>;
+ };
+ };
};
partition@50000 {
};
ðernet {
- mtd-mac-address = <&factory 0x4>;
- mediatek,portmap = "wllll";
+ nvmem-cells = <&macaddr_factory_4>;
+ nvmem-cell-names = "mac-address";
+
+ mediatek,portmap = "llllw";
};
&wmac {
- ralink,mtd-eeprom = <&factory 0>;
+ nvmem-cells = <&eeprom_factory_0>;
+ nvmem-cell-names = "eeprom";
};
-&pinctrl {
- state_default: pinctrl0 {
- default {
- ralink,group = "i2c", "uartf", "wled", "spi refclk", "pa";
- ralink,function = "gpio";
- };
+&state_default {
+ default {
+ groups = "i2c", "uartf", "wled", "spi refclk", "pa";
+ function = "gpio";
+ };
- /*
- * The sd function of the nd_sd group configures two of the
- * groups pins as gpios. The pins are used as PCIe reset/power.
- * Due to the driver load order, the pins are configured way to
- * late if triggered by the sd-card driver.
- * To not introduce another kind of driver load order
- * dependency and configure the pins as early as possible,
- * means during pinmux driver load.
- */
- gpio_sd {
- ralink,group = "nd_sd";
- ralink,function = "sd";
- };
+ /*
+ * The sd function of the nd_sd group configures two of the
+ * groups pins as gpios. The pins are used as PCIe reset/power.
+ * Due to the driver load order, the pins are configured way to
+ * late if triggered by the sd-card driver.
+ * To not introduce another kind of driver load order
+ * dependency and configure the pins as early as possible,
+ * means during pinmux driver load.
+ */
+ gpio_sd {
+ groups = "nd_sd";
+ function = "sd";
};
};