-#include "mt7621.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "mt7621_xiaomi_nand_128m.dtsi"
+#include <dt-bindings/leds/common.h>
/ {
compatible = "xiaomi,mi-router-3g", "mediatek,mt7621-soc";
label-mac-device = &gmac0;
};
- chosen {
- bootargs = "console=ttyS0,115200n8";
- };
-
leds {
compatible = "gpio-leds";
- led_status_red: status_red {
+ led_status_red: led-0 {
label = "red:status";
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_STATUS;
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
};
- led_status_blue: status_blue {
+ led_status_blue: led-1 {
label = "blue:status";
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_STATUS;
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
};
- led_status_yellow: status_yellow {
+ led_status_yellow: led-2 {
label = "yellow:status";
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_STATUS;
gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
};
- wan_amber {
+ led-3 {
label = "amber:wan";
+ color = <LED_COLOR_ID_AMBER>;
+ function = LED_FUNCTION_WAN;
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
- linux,default-trigger = "dsa-0.0:01:1Gbps";
+ linux,default-trigger = "mt7530-0:01:1Gbps";
};
- lan1_amber {
+ led-4 {
label = "amber:lan1";
+ color = <LED_COLOR_ID_AMBER>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <1>;
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
- linux,default-trigger = "dsa-0.0:03:1Gbps";
+ linux,default-trigger = "mt7530-0:03:1Gbps";
};
- lan2_amber {
+ led-5 {
label = "amber:lan2";
+ color = <LED_COLOR_ID_AMBER>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <2>;
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
- linux,default-trigger = "dsa-0.0:02:1Gbps";
- };
- };
-
- keys {
- compatible = "gpio-keys";
-
- reset {
- label = "reset";
- gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
+ linux,default-trigger = "mt7530-0:02:1Gbps";
};
};
vbus-supply = <®_usb_vbus>;
};
-&nand {
- status = "okay";
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "Bootloader";
- reg = <0x0 0x80000>;
- read-only;
- };
-
- partition@80000 {
- label = "Config";
- reg = <0x80000 0x40000>;
- };
-
- partition@c0000 {
- label = "Bdata";
- reg = <0xc0000 0x40000>;
- read-only;
- };
-
- factory: partition@100000 {
- label = "factory";
- reg = <0x100000 0x40000>;
- read-only;
- };
-
- partition@140000 {
- label = "crash";
- reg = <0x140000 0x40000>;
- };
-
- partition@180000 {
- label = "crash_syslog";
- reg = <0x180000 0x40000>;
- };
-
- partition@1c0000 {
- label = "reserved0";
- reg = <0x1c0000 0x40000>;
- read-only;
- };
-
- /* uboot expects to find kernels at 0x200000 & 0x600000
- * referred to as system 1 & system 2 respectively.
- * a kernel is considered suitable for handing control over
- * if its linux magic number exists & uImage CRC are correct.
- * If either of those conditions fail, a matching sys'n'_fail flag
- * is set in uboot env & a restart performed in the hope that the
- * alternate kernel is okay.
- * if neither kernel checksums ok and both are marked failed, system 2
- * is booted anyway.
- *
- * Note uboot's tftp flash install writes the transferred
- * image to both kernel partitions.
- */
-
- partition@200000 {
- label = "kernel_stock";
- reg = <0x200000 0x400000>;
- };
-
- partition@600000 {
- label = "kernel";
- reg = <0x600000 0x400000>;
- };
-
- /* ubi partition is the result of squashing
- * next consecutive stock partitions:
- * - rootfs0 (rootfs partition for stock kernel0),
- * - rootfs1 (rootfs partition for stock failsafe kernel1),
- * - overlay (used as ubi overlay in stock fw)
- * resulting 117,5MiB space for packages.
- */
-
- partition@a00000 {
- label = "ubi";
- reg = <0xa00000 0x7580000>;
- };
- };
-};
-
&pcie {
status = "okay";
};
};
&gmac0 {
- mtd-mac-address = <&factory 0xe006>;
+ nvmem-cells = <&macaddr_factory_e006>;
+ nvmem-cell-names = "mac-address";
};
&switch0 {
port@1 {
status = "okay";
label = "wan";
- mtd-mac-address = <&factory 0xe000>;
+ nvmem-cells = <&macaddr_factory_e000>;
+ nvmem-cell-names = "mac-address";
};
port@2 {
function = "gpio";
};
};
+
+&factory {
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_factory_e000: macaddr@e000 {
+ reg = <0xe000 0x6>;
+ };
+
+ macaddr_factory_e006: macaddr@e006 {
+ reg = <0xe006 0x6>;
+ };
+};