--- /dev/null
+#
+# Copyright (C) 2010 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+include $(TOPDIR)/rules.mk
+include $(INCLUDE_DIR)/kernel.mk
+
+PKG_NAME:=u-boot
+PKG_VERSION:=2010.03
+PKG_RELEASE:=1
+
+PKG_BUILD_DIR:=$(KERNEL_BUILD_DIR)/$(PKG_NAME)-$(BUILD_VARIANT)/$(PKG_NAME)-$(PKG_VERSION)
+PKG_SOURCE:=$(PKG_NAME)-$(PKG_VERSION).tar.bz2
+PKG_SOURCE_URL:=ftp://ftp.denx.de/pub/u-boot
+PKG_MD5SUM:=
+PKG_TARGETS:=bin
+
+include $(INCLUDE_DIR)/package.mk
+
+define uboot/Default
+ TITLE:=
+ CONFIG:=
+ IMAGE:=
+endef
+
+define uboot/sheevaplug
+ TITLE:=U-boot for the Sheevaplug
+endef
+
+define uboot/dockstar
+ TITLE:=U-boot for the Seagate Dockstar
+endef
+
+UBOOTS:=sheevaplug dockstar
+
+define Package/uboot/template
+define Package/uboot-kirkwood-$(1)
+ SECTION:=boot
+ CATEGORY:=Boot Loaders
+ DEPENDS:=@TARGET_kirkwood
+ TITLE:=$(2)
+ URL:=http://www.denx.de/wiki/U-Boot
+ VARIANT:=$(1)
+endef
+endef
+
+define BuildUbootPackage
+ $(eval $(uboot/Default))
+ $(eval $(uboot/$(1)))
+ $(call Package/uboot/template,$(1),$(TITLE))
+endef
+
+
+ifdef BUILD_VARIANT
+$(eval $(call uboot/$(BUILD_VARIANT)))
+UBOOT_CONFIG:=$(if $(CONFIG),$(CONFIG),$(BUILD_VARIANT))
+UBOOT_IMAGE:=$(if $(IMAGE),$(IMAGE),openwrt-$(BOARD)-$(BUILD_BARIANT)-u-boot.bin)
+endif
+
+define Build/Prepare
+ $(call Build/Prepare/Default)
+ $(CP) ./files/* $(PKG_BUILD_DIR) || true
+ find $(PKG_BUILD_DIR) -name .svn | $(XARGS) rm -rf
+endef
+
+define Build/Configure
+ $(MAKE) -C $(PKG_BUILD_DIR) \
+ $(UBOOT_CONFIG)_config
+endef
+
+define Build/Compile
+ $(MAKE) -C $(PKG_BUILD_DIR) \
+ CROSS_COMPILE=$(TARGET_CROSS)
+endef
+
+define Package/uboot/install/default
+ $(INSTALL_DIR) $(BIN_DIR)
+ $(CP) $(PKG_BUILD_DIR)/u-boot.bin \
+ $(BIN_DIR)/openwrt-$(BOARD)-$(1)-u-boot.bin
+endef
+
+define Package/uboot/install/template
+define Package/uboot-kirkwood-$(1)/install
+ $(call Package/uboot/install/default,$(2))
+endef
+endef
+
+$(foreach u,$(UBOOTS), \
+ $(eval $(call Package/uboot/install/template,$(u),$(u))) \
+)
+
+$(foreach u,$(UBOOTS), \
+ $(eval $(call BuildUbootPackage,$(u))) \
+ $(eval $(call BuildPackage,uboot-kirkwood-$(u))) \
+)
--- /dev/null
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := dockstar.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+TEXT_BASE = 0x00800000
+
+# Kirkwood Boot Image configuration file
+KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg
--- /dev/null
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include "dockstar.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+ /*
+ * default gpio configuration
+ * There are maximum 64 gpios controlled through 2 sets of registers
+ * the below configuration configures mainly initial LED status
+ */
+ kw_config_gpio(DOCKSTAR_OE_VAL_LOW,
+ DOCKSTAR_OE_VAL_HIGH,
+ DOCKSTAR_OE_LOW, DOCKSTAR_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ u32 kwmpp_config[] = {
+ MPP0_NF_IO2,
+ MPP1_NF_IO3,
+ MPP2_NF_IO4,
+ MPP3_NF_IO5,
+ MPP4_NF_IO6,
+ MPP5_NF_IO7,
+ MPP6_SYSRST_OUTn,
+ MPP7_GPO,
+ MPP8_UART0_RTS,
+ MPP9_UART0_CTS,
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP12_SD_CLK,
+ MPP13_SD_CMD,
+ MPP14_SD_D0,
+ MPP15_SD_D1,
+ MPP16_SD_D2,
+ MPP17_SD_D3,
+ MPP18_NF_IO0,
+ MPP19_NF_IO1,
+ MPP20_GPIO,
+ MPP21_GPIO,
+ MPP22_GPIO,
+ MPP23_GPIO,
+ MPP24_GPIO,
+ MPP25_GPIO,
+ MPP26_GPIO,
+ MPP27_GPIO,
+ MPP28_GPIO,
+ MPP29_TSMP9,
+ MPP30_GPIO,
+ MPP31_GPIO,
+ MPP32_GPIO,
+ MPP33_GPIO,
+ MPP34_GPIO,
+ MPP35_GPIO,
+ MPP36_GPIO,
+ MPP37_GPIO,
+ MPP38_GPIO,
+ MPP39_GPIO,
+ MPP40_GPIO,
+ MPP41_GPIO,
+ MPP42_GPIO,
+ MPP43_GPIO,
+ MPP44_GPIO,
+ MPP45_GPIO,
+ MPP46_GPIO,
+ MPP47_GPIO,
+ MPP48_GPIO,
+ MPP49_GPIO,
+ 0
+ };
+ kirkwood_mpp_conf(kwmpp_config);
+
+ /*
+ * arch number of board
+ */
+ gd->bd->bi_arch_number = MACH_TYPE_DOCKSTAR;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ int i;
+
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+ gd->bd->bi_dram[i].start = kw_sdram_bar(i);
+ gd->bd->bi_dram[i].size = kw_sdram_bs(i);
+ }
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and enable MV88E1116 PHY */
+void reset_phy(void)
+{
+ u16 reg;
+ u16 devadr;
+ char *name = "egiga0";
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ /* command to read PHY dev address */
+ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+ printf("Err..%s could not read PHY dev address\n",
+ __FUNCTION__);
+ return;
+ }
+
+ /*
+ * Enable RGMII delay on Tx and Rx for CPU port
+ * Ref: sec 4.7.2 of chip datasheet
+ */
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
+ miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
+ reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+ miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
+
+ /* reset the phy */
+ miiphy_reset(name, devadr);
+
+ printf("88E1116 Initialized on %s\n", name);
+}
+#endif /* CONFIG_RESET_PHY_R */
--- /dev/null
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __DOCKSTAR_H
+#define __DOCKSTAR_H
+
+#define DOCKSTAR_OE_LOW (~(0))
+#define DOCKSTAR_OE_HIGH (~(0))
+#define DOCKSTAR_OE_VAL_LOW (1 << 29) /* USB_PWEN low */
+#define DOCKSTAR_OE_VAL_HIGH (1 << 17) /* LED pin high */
+
+/* PHY related */
+#define MV88E1116_LED_FCTRL_REG 10
+#define MV88E1116_CPRSP_CR3_REG 21
+#define MV88E1116_MAC_CTRL_REG 21
+#define MV88E1116_PGADR_REG 22
+#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
+#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
+
+#endif /* __DOCKSTAR_H */
--- /dev/null
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM nand
+NAND_ECC_MODE default
+NAND_PAGE_SIZE 0x0800
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1b1b1b9b
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xFFD01400 0x43000c30 # DDR Configuration register
+# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
+# bit23-14: zero
+# bit24: 1= enable exit self refresh mode on DDR access
+# bit25: 1 required
+# bit29-26: zero
+# bit31-30: 01
+
+DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
+# bit 4: 0=addr/cmd in smame cycle
+# bit 5: 0=clk is driven during self refresh, we don't care for APX
+# bit 6: 0=use recommended falling edge of clk for addr/cmd
+# bit14: 0=input buffer always powered up
+# bit18: 1=cpu lock transaction enabled
+# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
+# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
+# bit30-28: 3 required
+# bit31: 0=no additional STARTBURST delay
+
+DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
+# bit3-0: TRAS lsbs
+# bit7-4: TRCD
+# bit11- 8: TRP
+# bit15-12: TWR
+# bit19-16: TWTR
+# bit20: TRAS msb
+# bit23-21: 0x0
+# bit27-24: TRRD
+# bit31-28: TRTP
+
+DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
+# bit6-0: TRFC
+# bit8-7: TR2R
+# bit10-9: TR2W
+# bit12-11: TW2W
+# bit31-13: zero required
+
+DATA 0xFFD01410 0x000000cc # DDR Address Control
+# bit1-0: 00, Cs0width=x8
+# bit3-2: 11, Cs0size=1Gb
+# bit5-4: 00, Cs1width=x8
+# bit7-6: 11, Cs1size=1Gb
+# bit9-8: 00, Cs2width=nonexistent
+# bit11-10: 00, Cs2size =nonexistent
+# bit13-12: 00, Cs3width=nonexistent
+# bit15-14: 00, Cs3size =nonexistent
+# bit16: 0, Cs0AddrSel
+# bit17: 0, Cs1AddrSel
+# bit18: 0, Cs2AddrSel
+# bit19: 0, Cs3AddrSel
+# bit31-20: 0 required
+
+DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
+# bit0: 0, OpenPage enabled
+# bit31-1: 0 required
+
+DATA 0xFFD01418 0x00000000 # DDR Operation
+# bit3-0: 0x0, DDR cmd
+# bit31-4: 0 required
+
+DATA 0xFFD0141C 0x00000C52 # DDR Mode
+# bit2-0: 2, BurstLen=2 required
+# bit3: 0, BurstType=0 required
+# bit6-4: 4, CL=5
+# bit7: 0, TestMode=0 normal
+# bit8: 0, DLL reset=0 normal
+# bit11-9: 6, auto-precharge write recovery ????????????
+# bit12: 0, PD must be zero
+# bit31-13: 0 required
+
+DATA 0xFFD01420 0x00000040 # DDR Extended Mode
+# bit0: 0, DDR DLL enabled
+# bit1: 0, DDR drive strenght normal
+# bit2: 0, DDR ODT control lsd (disabled)
+# bit5-3: 000, required
+# bit6: 1, DDR ODT control msb, (disabled)
+# bit9-7: 000, required
+# bit10: 0, differential DQS enabled
+# bit11: 0, required
+# bit12: 0, DDR output buffer enabled
+# bit31-13: 0 required
+
+DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
+# bit2-0: 111, required
+# bit3 : 1 , MBUS Burst Chop disabled
+# bit6-4: 111, required
+# bit7 : 0
+# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
+# bit9 : 0 , no half clock cycle addition to dataout
+# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 1111 required
+# bit31-16: 0 required
+
+DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
+DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
+
+DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
+DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
+# bit0: 1, Window enabled
+# bit1: 0, Write Protect disabled
+# bit3-2: 00, CS0 hit selected
+# bit23-4: ones, required
+# bit31-24: 0x0F, Size (i.e. 256MB)
+
+DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb
+DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1
+
+DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
+
+DATA 0xFFD01494 0x00030000 # DDR ODT Control (Low)
+DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
+# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
+# bit3-2: 01, ODT1 active NEVER!
+# bit31-4: zero, required
+
+DATA 0xFFD0149C 0x0000E803 # CPU ODT Control
+DATA 0xFFD01480 0x00000001 # DDR Initialization Control
+#bit0=1, enable DDR init upon this register write
+
+# End of Header extension
+DATA 0x0 0x0
--- /dev/null
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_SHEEVAPLUG_H
+#define _CONFIG_SHEEVAPLUG_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING "\nMarvell-Sheevaplug"
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_MARVELL 1
+#define CONFIG_ARM926EJS 1 /* Basic Architecture */
+#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
+#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
+#define CONFIG_KW88F6281 1 /* SOC Name */
+#define CONFIG_MACH_SHEEVAPLUG /* Machine type */
+
+#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
+
+/*
+ * CLKs configurations
+ */
+#define CONFIG_SYS_HZ 1000
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
+
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you want to use
+ * for your console driver.
+ */
+
+#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
+ 115200,230400, 460800, 921600 }
+/* auto boot */
+#define CONFIG_BOOTDELAY 3 /* default enable autoboot */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
+
+#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+
+/*
+ * NAND configuration
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_KIRKWOOD
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */
+#define NAND_ALLOW_ERASE_ALL 1
+#endif
+
+/*
+ * Environment variables configurations
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
+#else
+#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
+#endif
+/*
+ * max 4k env size is enough, but in case of nand
+ * it has to be rounded to sector size
+ */
+#define CONFIG_ENV_SIZE 0x20000 /* 128k */
+#define CONFIG_ENV_ADDR 0x140000
+#define CONFIG_ENV_OFFSET 0x140000 /* env starts here */
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \
+ "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
+ "${x_bootcmd_usb}; bootm 0x6400000;"
+
+#define CONFIG_MTDPARTS "orion_nand:1M(u-boot)," \
+ "1M@1M(second_stage_u-boot)," \
+ "3M@2M(kernel),64M@5M(rootfs),187M@69M(data) rw\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
+ "=ttyS0,115200 mtdparts="CONFIG_MTDPARTS \
+ "x_bootcmd_kernel=nand read 0x6400000 0x200000 0x300000\0" \
+ "x_bootcmd_usb=usb start\0" \
+ "x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2\0"
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 128) /* 128kB for malloc() */
+/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE 128
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */
+#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
+#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
+#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
+#define CONFIG_NR_DRAM_BANKS 4
+#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */
+#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */
+#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
+#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* specify more that one ports available */
+#define CONFIG_MII /* expose smi ove miiphy interface */
+#define CONFIG_KIRKWOOD_EGIGA /* Enable kirkwood Gbe Controller Driver */
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
+#define CONFIG_KIRKWOOD_EGIGA_PORTS {1,0} /* enable port 0 only */
+#define CONFIG_PHY_BASE_ADR 0
+#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
+#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * USB/EHCI
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#endif /* CONFIG_CMD_USB */
+
+#define CONFIG_SERVERIP 169.254.254.254
+#define CONFIG_IPADDR 169.254.254.243
+#endif /* _CONFIG_SHEEVAPLUG_H */
--- /dev/null
+--- a/Makefile
++++ b/Makefile
+@@ -3039,6 +3039,9 @@
+ sheevaplug_config: unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
+
++dockstar_config: unconfig
++ @$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
++
+ smdk2400_config : unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm920t smdk2400 samsung s3c24x0
+
+--- a/include/asm-arm/mach-types.h
++++ b/include/asm-arm/mach-types.h
+@@ -2699,6 +2699,7 @@
+ #define MACH_TYPE_MX53_EVK 2716
+ #define MACH_TYPE_IGEP0030 2717
+ #define MACH_TYPE_AXELL_H40_H50_CTRL 2718
++#define MACH_TYPE_DOCKSTAR 2998
+
+ #ifdef CONFIG_ARCH_EBSA110
+ # ifdef machine_arch_type
projects / openwrt / staging / chunkeey.git / commitdiff